LM2904VDMR2G - Dual 1MHz Op Amp, 3-32V | onsemi
MPN: LM2904VDMR2G ✓ چالاکLM2904VDMR2G گشتی
An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to compare an input signal with a feedback network. The LM2904 family combines low power consumption, internal frequency compensation, and common-mode input capability reaching ground or VEE. Its dual-channel configuration places two independent amplifiers in one package, reducing component count in applications requiring matched signal paths, sensing, buffering, or error amplification.
The principal features are a 3 V to 32 V operating range, approximately 1 MHz gain-bandwidth product, dual-circuit construction, and support for single or split supplies. The common-mode input range is particularly useful in battery systems because the amplifier can operate close to the negative supply rail. Its MSOP-8 package supports compact layouts, while the low-power operating characteristics suit portable and industrial-control equipment.
Internally frequency-compensated channels remove the need for an external compensation network in ordinary closed-loop gain configurations. Each channel can operate independently, allowing simultaneous use as two amplifiers. Designers must still observe output-swing, input-voltage, supply-current, and common-mode limits. Configuration as a voltage follower, non-inverting amplifier, or inverting amplifier will determine signal gain and feedback-component values.
Typical applications include sensor-interface conditioning, low-side current measurement, industrial control loops, battery-powered monitoring, transducer amplification, and general-purpose analog signal processing. The split-supply capability is useful when bipolar sensor signals must be amplified around ground. In single-supply systems, the ground-reaching common-mode range helps simplify biasing near the lower rail.
A key design consideration is to verify output swing under the intended load and to place input and feedback components close to their pins to minimize parasitic pickup. Decoupling capacitors should connect directly between each supply pin and ground. Stable operation should be confirmed across supply voltage, temperature, output loading, and the selected gain because the internal compensation does not remove all application-level stability constraints.
This page combines electrical characteristics, package information, drop-in alternatives, comparison parameters, and practical circuit guidance to accelerate component selection. It supports engineers comparing general-purpose dual amplifiers for industrial, automotive, and low-voltage analog systems while emphasizing the need to verify exact pinout, qualification, and operating limits before substitution.
جێگرەوەکانی جێگۆڕکێ بۆ LM2904VDMR2G — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2904VDMR2G (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Common-Mode Input Range, Package.
LM2904DMR2G
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2904ADMR2G
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2904BDMR2G
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2904BADMR2G
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2904VDMR2G زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Number of Amplifier Channels | 2 channels |
| Amplifier Type | 2-circuit general-purpose operational amplifier |
| Supply Voltage Range | 3.0 V to 32 V |
| Gain-Bandwidth Product | 1 MHz |
| Common-Mode Input Range | Extending to ground or VEE |
| Supply Configuration | Single supply or split supply |
| Frequency Compensation | Internally compensated per channel |
| ژمارەی پینەکان | 8 pins |
| پاکێج | MSOP-8, surface mount |
ڕێکخستنی پینی LM2904VDMR2G
| پین 1 | OUT1 — Channel 1 output |
| پین 2 | -IN1 — Channel 1 inverting input |
| پین 3 | +IN1 — Channel 1 non-inverting input |
| پین 4 | V- — Negative supply connection |
| پین 5 | +IN2 — Channel 2 non-inverting input |
| پین 6 | -IN2 — Channel 2 inverting input |
| پین 7 | OUT2 — Channel 2 output |
| پین 8 | V+ — Positive supply connection |
بەکارهێنانە باوەکان
LM2904VDMR2G گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Signal Conditioning, Battery-Powered Monitoring, Automotive Control and Sensor Interface, Low-Side Current Measurement, Audio and Communications Interface, Process Control Error Amplifier.
Industrial Sensor Signal Conditioning
The LM2904VDMR2G suits low-bandwidth industrial sensor conditioning because its two independent channels can amplify or buffer separate inputs within one 8-pin MSOP package. The 3 V to 32 V supply range accommodates common industrial rails, while the 1 MHz gain-bandwidth product is more than adequate for many temperature, pressure, level, and position sensors. Its common-mode input range extending toward ground or VEE is valuable when sensor outputs sit close to the lower supply rail. Use the amplifier in a non-inverting or differential stage with feedback resistors selected for the required gain, and place input and feedback parts close to the pins to reduce pickup. Verify the actual sensor excitation level, output swing, and input common-mode condition against the onsemi datasheet.
پێشنیارکراو
Battery-Powered Monitoring
The LM2904VDMR2G is appropriate for battery-powered monitoring because it operates from 3 V to 32 V and is designed for low power consumption. The common-mode input capability reaching toward ground or VEE simplifies amplification of signals produced by current, resistive, or threshold sensors in portable equipment. Its 1 MHz bandwidth comfortably supports temperature, state-of-charge, and environmental measurements rather than high-speed waveform acquisition. Both channels can monitor two independent quantities, reducing package count. The principal trade-off is that a general-purpose bipolar input stage can require more headroom than rail-to-rail-input amplifiers near the positive rail, so biasing and signal swing must be checked. Stable bypass capacitance and careful grounding remain necessary as battery impedance varies.
پێشنیارکراو
Automotive Control and Sensor Interface
The LM2904VDMR2G can support automotive control and sensor-interface circuits where a rugged dual operational amplifier, broad supply range, and common-mode operation near ground are valuable. The 3 V to 32 V supply capability covers many 12 V and 24 V vehicle environments, while 1 MHz bandwidth is appropriate for many control and actuator-feedback signals. Two channels can implement gain, filtering, or active differential functions in a compact MSOP-8 footprint. Automotive production use requires confirming the exact suffix qualification, temperature grade, AEC-Q100 status, and operating limits from the manufacturer documentation. The design should also account for transient suppression, grounding, and component selection for the vehicle environment rather than relying on the operational amplifier alone for protection.
پێشنیارکراو
Low-Side Current Measurement
The LM2904VDMR2G can amplify the small voltage generated by a low-side current shunt while operating from a single supply or split rails. Its common-mode input range extending toward ground or VEE is useful when the shunt voltage is small relative to the supply, and its 1 MHz bandwidth supports measurement bandwidth well beyond typical slow current-loop signals. A dual package can process the shunt voltage and a reference signal, enabling offset subtraction or output filtering. Resistance and lead length of the shunt determine achievable accuracy, while input bias current contributes an error across the shunt network. Keep the amplifier input routes short, use a defined ground reference, and verify offset voltage, input bias current, and output drive against the manufacturer datasheet before calibrating the measurement path.
پێشنیارکراو
Audio and Communications Interface
The LM2904VDMR2G is suitable for low-level audio and communications interface circuits that do not require rail-to-rail input operation or wide bandwidth. Its two channels can provide gain, impedance conversion, active filtering, or differential receive functions, while the common-mode range extending toward ground supports single-supply microphone-style signal paths. The 1 MHz gain-bandwidth product provides ample loop bandwidth for voice-band and low-rate control signals. However, the device is not a precision audio part, and input offset, noise, slew rate, and output swing should be reviewed against the required signal quality. Place the amplifier near the source, keep high-impedance input traces short, and provide local supply bypassing to prevent communications transients from coupling into the audio path.
پێشنیارکراو
Process Control Error Amplifier
The LM2904VDMR2G can serve as an error amplifier or actuator-drive stage in a basic industrial process-control loop. Its dual-channel configuration allows one channel to process the feedback error while the other amplifies the command signal, and the 1 MHz bandwidth supports many slow temperature, pressure, and flow loops. Operation from 3 V to 32 V provides flexibility across control rails, while common-mode input capability extending toward ground simplifies feedback signals referenced to the lower rail. Stability must be established for the selected compensation network and load, particularly when driving capacitive inputs or long cables. Add appropriate isolation and protection at external interfaces, verify output-current limits, and test loop response across supply and temperature variations before connecting the circuit to a plant process.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2904VDMR2G — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2904DMR2G | LM2904ADMR2G | LM2904BDMR2G | LM2904BADMR2G |
|---|---|---|---|---|---|
| Package | MSOP-8 | MSOP-8 | MSOP-8 | MSOP-8 | MSOP-8 |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Supply Voltage Range | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V | 3 V to 32 V |
| Gain-Bandwidth Product | 1 MHz | 1 MHz | 1 MHz | 1 MHz | 1 MHz |
| Common-Mode Input Range | Extending to ground or VEE | Extending to ground or VEE | Extending to ground or VEE | Extending to ground or VEE | Extending to ground or VEE |
| Supply Operation | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply |
| Compensation | Internally compensated | Internally compensated | Internally compensated | Internally compensated | Internally compensated |
جیاکەرەوە سەرەکییەکان
- Combines two independent channels in a compact MSOP-8 package (بەراورد بەLM2904DMR2G)
- Supports ground-reaching common-mode input operation (بەراورد بەLM2904ADMR2G)
- Wide supply range supports industrial and vehicle rails (بەراورد بەLM2904BDMR2G)
- Single- and split-supply flexibility (بەراورد بەLM2904BADMR2G)
تێبینییەکانی دیزاین
Place the positive and negative supply bypass capacitors directly beside the V+ and V− pins, with very short connections to the ground plane. Route both input pins and feedback components away from switching nodes and high-current return paths. Because the MSOP-8 footprint is compact, preserve access to the input pins during assembly and avoid long exposed copper that can collect contamination or behave as an antenna.
Do not assume that a common-mode input range extending to ground or VEE guarantees full rail-to-rail operation at the positive rail. Check input and output limits for the actual 3 V to 32 V operating range, especially when the output must approach a supply rail. Also verify bias-current-generated error in high-impedance sensor circuits and ensure the selected feedback network maintains stable closed-loop operation.
Keep non-inverting input traces short and guard them against nearby switching or relay-control wiring. Place output components far enough from sensitive inputs to prevent unintended feedback through parasitic capacitance. For split supplies, join the two supply-ground references at a deliberate, low-impedance point and provide adequate return-current paths so output and input-reference currents do not share a narrow trace segment.
The 1 MHz gain-bandwidth product is appropriate for low-bandwidth control and sensor signals, but high-capacitance loads can reduce stability margin. Keep output routing short, isolate capacitive loads according to the manufacturer guidance, and add a small isolation resistor when required. Validate phase margin at the intended gain because generic closed-loop configurations do not guarantee stability with every load and feedback network.
زانیاری پابەندبوون
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was included in the product documentation links. Verify compliance for the exact ordering code with onsemi.