LM324DRG3 - 4-Channel 1.2MHz Op Amp | Texas Instruments
MPN: LM324DRG3 ✓ چالاکLM324DRG3 گشتی
An operational amplifier is a voltage-feedback analog IC that uses differential input voltage to control an amplified output. The LM324 family combines four amplifiers in one package, reducing component count and simplifying layout for low-frequency instrumentation, sensor interfaces, audio paths, and industrial control circuits. Its frequency compensation provides stable operation without an external compensation network in typical closed-loop configurations.
The LM324DRG3 provides four general-purpose amplifier circuits, a 1.2 MHz gain-bandwidth product, and a 0.5 V/µs slew rate. Its supply current is listed at 0.8 mA typical, with low supply-current drain described as independent of supply voltage. These characteristics make it practical for battery-operated and low-power analog systems where bandwidth beyond audio and general instrumentation frequencies is not required.
Each amplifier is independent, allowing one package to serve four separate signal channels. The device is designed for single-supply operation, split-supply operation, and standard feedback-control topologies. Because its bandwidth and slew rate are modest, applications requiring wideband precision, high output current, rail-to-rail input or output, or fast settling should use a more specialized amplifier family instead.
Typical uses include low-frequency sensor conditioning, current-to-voltage conversion, audio preamplification, low-level signal buffering, and general industrial control loops. A common circuit places a resistive feedback network around each amplifier, uses the fourth channel for biasing or active filtering, and decouples the supply pins close to the package with a local bypass capacitor.
Design around the 14-pin SOIC footprint and verify the exact pinout in the manufacturer pin-description table before assigning tracks. Keep input and feedback resistors close to their associated pins to minimize parasitic capacitance and oscillation risk. Check output swing, input common-mode range, output loading, and supply limits against the circuit operating points before production release.
This page organizes the verified LM324DRG3 specifications, package information, comparisons, and design guidance into one engineering-focused reference. It also distinguishes exact drop-in options from broader functional alternatives and identifies where additional datasheet review is required before substitution.
جێگرەوەکانی جێگۆڕکێ بۆ LM324DRG3 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM324DRG3 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Mounting Type, Architecture, Frequency Compensation.
LM324DR2G
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM324DR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM324DRG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM324D
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM324DRG3 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Number of Amplifier Circuits | 4 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/µs |
| Supply Current Drain | 0.8 mA typical |
| Supply Configuration | Single supply or split supply |
| Channel Independence | 4 independent amplifiers |
| Frequency Compensation | Internally frequency-compensated |
| پاکێج | 14-SOIC, 0.154 inch / 3.90 mm width |
| Package Type | Cut Tape (CT) |
| جۆری دامەزراندن | 14-pin surface-mount SOIC |
| دۆخی RoHS | RoHS-compliant |
| Lead-Free Status | Lead-free |
ڕێنمایی ڕێکخستنی پینی LM324DRG3 cut tape (ct)
ڕێکخستنی پین بۆ LM324DRG3 (پاکێجی cut tape (ct)). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM324DRG3.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM324DRG3 گونجاوە بۆ 6 بەکارھێنانs: Low-Frequency Sensor Conditioning, Audio Preamplification and Buffering, Industrial Control Loops, Current-to-Voltage Conversion, Active Filtering and Signal Conditioning, General-Purpose Buffering and Level Conditioning.
Low-Frequency Sensor Conditioning
The LM324DRG3 fits sensor-conditioning circuits that amplify small differential signals into a usable voltage range. Its four independent channels allow two amplifiers to form a differential input stage while the remaining channels perform reference buffering or active filtering. The 1.2 MHz gain-bandwidth product supports modest closed-loop bandwidth, and the 0.5 V/µs slew rate is adequate for signals well below its full capability. Because this is not a rail-to-rail precision amplifier, verify input common-mode range, output swing, input bias current, and noise against the sensor output before selecting the gain. Place feedback components close to the associated amplifier pins and provide a local supply bypass capacitor to improve stability and transient response.
پێشنیارکراو
Audio Preamplification and Buffering
The LM324DRG3 can provide low-frequency gain and impedance buffering in line-level audio preamplifier or mixer sections. Its 1.2 MHz gain-bandwidth product exceeds the bandwidth required for many conventional audio-band paths, while the 0.5 V/µs slew rate provides useful headroom for moderate signal amplitudes. Four independent channels can process stereo and auxiliary paths within one package. The design must remain inside the amplifier's input common-mode and output-swing limits, particularly when operating from a single supply. Use resistive gain-setting networks with practical values, avoid excessive capacitive loading on the outputs, and verify distortion and stability at the intended closed-loop gain and load impedance.
پێشنیارکراو
Industrial Control Loops
The LM324DRG3 is appropriate for low-frequency industrial control, error-amplifier, and actuator-feedback functions where four channels are useful on one board. Its internally compensated architecture simplifies conventional inverting and non-inverting amplifier layouts, and its 1.2 MHz gain-bandwidth product is suitable for slow control loops. The 0.8 mA typical supply-current figure also supports compact low-power analog sections. However, industrial qualification, operating-temperature limits, input protection, and output drive must be verified for the specific environment. Place high-impedance summing nodes away from switching traces, provide local bypass capacitance, and check that the selected external feedback network preserves stable operation at the intended gain.
پێشنیارکراو
Current-to-Voltage Conversion
The LM324DRG3 can serve as the transimpedance amplifier in a low-frequency current-to-voltage converter when the source impedance and bandwidth are moderate. The feedback resistor converts input current into a proportional output voltage, while the 1.2 MHz gain-bandwidth product provides more bandwidth than many slow sensor and monitoring applications require. Input bias current, input capacitance, output swing, and the practical stability of the transimpedance network remain important constraints. Use a feedback capacitor when required to control bandwidth and noise, keep the input trace short, and avoid routing it beside noisy switching nodes. Confirm that output polarity and signal polarity are correct for the intended current direction.
پێشنیارکراو
Active Filtering and Signal Conditioning
The four internal amplifiers of the LM324DRG3 can implement active filters, comparators with hysteresis, sample-and-hold support circuitry, and multiple gain stages in one package. Its internally frequency-compensated design is well suited to closed-loop configurations operating below the 1.2 MHz gain-bandwidth product, making it useful for low-frequency filtering and general conditioning rather than high-speed signal processing. Component tolerances determine passive-network accuracy, while amplifier noise, output loading, and slew rate influence large-signal behavior. Keep each stage's feedback loop compact, avoid excessive source impedance at the input, and use the remaining channels for biasing or active compensation when that improves system performance.
پێشنیارکراو
General-Purpose Buffering and Level Conditioning
The LM324DRG3 works well for impedance buffering, gain correction, and level conditioning between sensors, logic interfaces, and measurement blocks. A voltage follower configuration provides a straightforward buffer, while inverting and non-inverting networks can set the required gain and offset relationships. The 1.2 MHz bandwidth is more than adequate for many slow control and instrumentation signals, and the 0.5 V/µs slew rate supports moderate output transitions. Confirm the input common-mode range and output swing for the selected supply, especially in single-supply systems. Use short, low-impedance input and feedback paths and ensure downstream loads do not exceed the amplifier's output-current and capacitive-load capabilities.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM324DRG3 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM324DR2G | LM324DR | LM324DRG4 | LM324D |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC | 14-SOIC - same footprint | 14-SOIC - same footprint | 14-SOIC - same footprint | 14-SOIC - same footprint |
| Number of Amplifier Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Amplifier Type | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Supply Configuration | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply | Single supply or split supply |
| Internal Frequency Compensation | Yes | Yes | Yes | Yes | Yes |
جیاکەرەوە سەرەکییەکان
- Four independent amplifiers in one 14-pin package (بەراورد بەLM2904P3)
- Industry-standard 1.2 MHz bandwidth (بەراورد بەLM201AD)
- Internal frequency compensation simplifies conventional feedback stages (بەراورد بەLM248DR)
تێبینییەکانی دیزاین
Route each amplifier's input, output, and feedback components as a compact loop around its SOIC pins. Long feedback traces increase susceptibility to parasitic feedback and can reduce stability margin. Place the input and feedback resistors close to the associated channel, keep sensitive input nodes away from switching-regulator and digital clock traces, and connect the bypass capacitor directly across the device's supply pins.
Do not assume that every LM324 ordering suffix has identical temperature, qualification, or lifecycle characteristics. The LM324B and LM324BA families have specification improvements, including a 3 V to 36 V supply range, that cannot automatically be applied to LM324DRG3. When replacing LM324DRG3, compare the exact suffix in the manufacturer ordering table and verify input offset, bias current, common-mode range, output swing, and supply limits.
Single-supply operation constrains the usable input and output ranges even though the internal amplifiers are independent. Bias the signal around the midpoint of the available output range when processing bipolar signals, and confirm that both the input common-mode range and output swing include the required operating points. The typical 0.8 mA supply-current figure is useful for power budgeting, but the final design must also include load current and bypass-capacitor requirements.
The 1.2 MHz gain-bandwidth product and 0.5 V/µs slew rate make LM324DRG3 appropriate primarily for low-frequency and audio-band amplification. At high closed-loop gain, evaluate noise gain across frequency and maintain the feedback network recommended by the manufacturer. Avoid using this device for wideband video, high-speed data acquisition, or precision ADC-driver applications requiring substantially greater bandwidth and slew rate.
زانیاری پابەندبوون
RoHS-compliant and lead-free status is stated in the LM324DRG3 product listing. No manufacturer statement establishing REACH, AEC-Q100, halogen-free, or conflict-minerals status was identified for the exact MPN.