onsemi

LM324DTBR2G - 4-Channel 32V Op Amp | onsemi | Industrial

MPN: LM324DTBR2G ✓ چالاک
3 V to 32 V Vdss 14-TSSOP, 0.173 in / 4.40 mm width Package
MOQ: 1 |

LM324DTBR2G گشتی

The onsemi LM324DTBR2G is a general-purpose, four-circuit operational amplifier with true differential inputs, a 3 V to 32 V supply-voltage range, 5 mV input-offset voltage, 1 MHz gain-bandwidth product, and 0.6 V/µs slew rate. The device is supplied in a 14-pin TSSOP package configured for tape-and-reel handling.

An operational amplifier is an analog signal-conditioning IC that compares two input voltages and amplifies the difference between them. In its wider hierarchy, the operational amplifier belongs to the amplifier IC family, the analog-processing family, and ultimately the semiconductor category. The LM324 series is specifically positioned as a low-cost general-purpose quad amplifier for single-supply applications, while also supporting conventional split-supply operation.

Four independent amplifier sections in one package make the LM324DTBR2G useful where a board needs multiple buffered channels without allocating four separate packages. Its 32 V maximum supply voltage provides useful headroom for industrial, control, and instrumentation circuits. The 1 MHz gain-bandwidth product supports general-purpose gain and buffering rather than demanding high-speed signal-chain applications. The 5 mV input-offset voltage is especially relevant when the amplified differential signal is small or when system calibration must account for amplifier input offset.

The LM324 architecture provides true differential inputs and internally compensated operation. Internally compensated amplifiers avoid the need for an external dominant-pole capacitor when operating in a conventional closed-loop configuration. This simplifies board design, although the bandwidth, output drive, and slew rate remain those of a general-purpose device rather than a precision or high-speed amplifier.

Typical uses include sensor-signal conditioning, current-to-voltage conversion, low-frequency active filtering, general instrumentation, audio preamplification, and industrial control interfaces. The four-channel organization can also reduce board area when several independent low-frequency analog signals must be amplified or buffered. Application-specific checks should confirm output swing, input common-mode range, load capability, noise, and stability.

Designers should place input and output bypassing capacitors close to their associated supply pins, maintain short feedback paths, and verify that the selected feedback network remains stable at the operating gain and capacitive load. Because this is a quad device, unused amplifier sections should still be configured conservatively to avoid floating inputs and unnecessary channel activity.

This product page consolidates the manufacturer-family characteristics, exact package information, practical application guidance, and a conservative drop-in comparison. It also distinguishes confirmed substitutions from package-only or functionally similar parts that should not be treated as true PCB drop-ins.

جێگرەوەکانی جێگۆڕکێ بۆ LM324DTBR2G — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM324DTBR2G (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Input Offset Voltage, Number of Amplifiers, Input Type.

onsemi
Package: 14-TSSOP
Amplifier Type: Standard / General Purpose Operational Amplifier
Input Offset Voltage: 7 mV
بەراوردکردن لەگەڵ LM324DTBR2G →
onsemi
Package: 14-TSSOP, 0.173 inch / 4.40 mm width
Number of Amplifiers: 4 circuits
بەراوردکردن لەگەڵ LM324DTBR2G →
onsemi
Package: 14-pin TSSOP
Input Offset Voltage: 5 mV maximum
بەراوردکردن لەگەڵ LM324DTBR2G →
Texas Instruments
Package: 14-pin TSSOP
Amplifier Type: Quad general-purpose operational amplifier
Number of Amplifiers: 4 independent amplifiers
بەراوردکردن لەگەڵ LM324DTBR2G →

LM324DTBR2

✅ جێگرەوەی ڕاستەوخۆ
onsemi
📦 14-TSSOP (0.173, 4.40 mm width)
Quad operational amplifier · 4 circuits · 3 V to 32 V · 5 mV maximum · True differential inputs · Standard general-purpose amplifier · 14-pin TSSOP · Surface mount

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM324DTBG

✅ جێگرەوەی ڕاستەوخۆ
onsemi
📦 14-TSSOP (0.173, 4.40 mm width)
General Purpose · 4 circuits · 3 V to 32 V · 1 MHz · 0.6 V/µs · 5 mV · True differential inputs · 14-TSSOP, 0.173 inch / 4.40 mm width

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM324DTBR2G زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Type General Purpose
Number of Circuits 4 circuits
Number of Amplifiers 4 amplifiers
Supply Voltage Range 3 V to 32 V
Input Offset Voltage 5 mV
Gain Bandwidth Product 1 MHz
Slew Rate 0.6 V/µs
Input Type True differential inputs
Compensation Internally compensated
Supply Type Single supply or split supply
Minimum Single-Supply Operation 3.0 V
Maximum Supply Voltage 32 V
پاکێج 14-TSSOP, 0.173 in / 4.40 mm width
جۆری دامەزراندن Surface mount
Packaging Tape and reel
Temperature Grade Commercial temperature grade
دۆخی RoHS unknown
REACH Status unknown

ڕێنمایی ڕێکخستنی پینی LM324DTBR2G 14-tssop, 0.173 in / 4.40 mm width

ڕێکخستنی پین بۆ LM324DTBR2G (پاکێجی 14-tssop, 0.173 in / 4.40 mm width). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 14-tssop, 0.173 in / 4.40 mm width بۆ LM324DTBR2G

هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM324DTBR2G.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

LM324DTBR2G گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Signal Conditioning, Current-to-Voltage Conversion, Active Filtering and Signal Buffering, Audio Preamplification, Process Control Interface, Low-Frequency Instrumentation.

🏭

Industrial Sensor Signal Conditioning

The LM324DTBR2G suits low-frequency industrial sensor conditioning because its true differential inputs can amplify the difference between two sensor nodes without requiring a separate input-referencing stage. According to the onsemi LM324 family information, the four integrated channels reduce package count, while the 1 MHz gain-bandwidth product and 0.6 V/µs slew rate support modest closed-loop gains and instrumentation signals. The 5 mV input-offset voltage must be included in the error budget for low-level measurements. Confirm the sensor’s common-mode range, source impedance, bandwidth, and the amplifier’s output-swing limits at the chosen 3 V to 32 V supply.

⚡

Current-to-Voltage Conversion

The LM324DTBR2G can provide the voltage-amplification stage of a current-to-voltage converter when a precision shunt and low-noise reference establish the input scale. Its true differential input arrangement helps reject common-mode voltage, while the four amplifier sections allow implementation of gain, filtering, output buffering, and auxiliary diagnostics in one package. The 0.6 V/µs slew rate is appropriate for many slowly changing process currents, and the 1 MHz gain-bandwidth product supports moderate closed-loop bandwidth. Check shunt power dissipation, input bias-current error, offset calibration, output swing, and stability with the complete external filter network.

🔧

Active Filtering and Signal Buffering

The LM324DTBR2G is appropriate for general-purpose active filtering and impedance buffering because it combines four internally compensated amplifier channels with a 1 MHz gain-bandwidth product. According to the onsemi LM324 datasheet, internal compensation removes the need for a dominant-pole compensation capacitor in conventional closed-loop configurations. Multiple channels can implement stages such as anti-alias filtering, gain conditioning, output isolation, and auxiliary buffering without four separate packages. Validate each filter stage with the actual source and load impedances because op-amp input bias current, output drive, and capacitive-load behavior affect low-frequency filters and sensor-source interfaces.

🎧

Audio Preamplification

The LM324DTBR2G can serve as a general-purpose audio preamplifier for low-frequency, low-gain stages where its 1 MHz gain-bandwidth product and 0.6 V/µs slew rate provide adequate bandwidth. The four amplifier sections allow stereo input amplification plus additional channels for tone shaping, buffering, or monitoring. According to the onsemi LM324 family documentation, the device is designed for single-supply applications, making a mid-supply reference practical in single-ended circuits. Verify the input and output common-mode range, headroom at the selected supply, output load, noise performance, and stability when driving capacitive inputs or long PCB traces.

🏭

Process Control Interface

The LM324DTBR2G fits process-control interfaces that require several low-frequency amplifier or buffer channels around a controller. According to the onsemi LM324 datasheet, it can operate from 3 V to 32 V, allowing integration with both low-voltage logic-side signals and higher-voltage industrial interface levels when properly scaled. The four-channel arrangement can handle sensor inputs, actuator feedback, and signal conditioning while reducing board area. The 5 mV input-offset specification and 1 MHz gain-bandwidth product must be reconciled with required accuracy and response time. Also verify common-mode limits, output swing, isolation strategy, and failure behavior before connecting external field wiring.

📟

Low-Frequency Instrumentation

The LM324DTBR2G is useful in bench and portable instrumentation requiring several general-purpose amplifier sections at modest frequency. Its true differential inputs support bridge and differential measurement paths, while the four-channel package can provide gain, active filtering, and output buffering in a compact TSSOP footprint. According to the onsemi LM324 family information, the 3 V minimum supply supports low-voltage portable systems, and the 32 V maximum supports higher-voltage laboratory interfaces. For precision measurement, assess offset, input bias current, drift, noise, and resistor matching rather than assuming the 5 mV offset is acceptable. Confirm grounding and layout to prevent injected error from long measurement leads.

What are the key specifications of LM324DTBR2G that engineers should know?
The LM324DTBR2G is a four-circuit general-purpose operational amplifier operating from 3 V to 32 V. According to the onsemi LM324 datasheet, it provides true differential inputs, 5 mV input-offset voltage, a 1 MHz gain-bandwidth product, and a 0.6 V/µs slew rate. The device is packaged in a 14-pin TSSOP and supplied on tape and reel. Its four integrated amplifier sections make it useful for general instrumentation, buffering, filtering, sensor conditioning, and low-frequency industrial control.
Where can I download the LM324DTBR2G datasheet PDF?
The LM324DTBR2G datasheet can be accessed through the listed onsemi document page at alldatasheet.com. According to the indexed manufacturer document, the LM324DTBR2G belongs to the LM324 series of single-supply quad operational amplifiers and is described as a 17-page document. For design sign-off, use the onsemi LM324 family documentation for pin assignments, electrical limits, application circuits, and package drawings, then confirm that the ordering suffix matches the intended package and shipping format.
What is the supply voltage range of the LM324DTBR2G?
The LM324DTBR2G operates from 3 V to 32 V. According to the onsemi LM324 datasheet, the quad amplifier can operate at supply voltages as low as 3.0 V or as high as 32 V and also supports split-supply operation. This wide range makes the device suitable for both low-voltage single-rail systems and higher-voltage industrial circuits, provided the selected operating point remains within the complete electrical ratings listed in the datasheet.
Where can I find the LM324DTBR2G pinout and package drawing?
Use the pin-description table and package drawing in the onsemi LM324 datasheet to confirm the LM324DTBR2G pinout. The component is a 14-pin TSSOP device, and its four amplifier sections are distributed across the package rather than assigned as four independent single-amplifier packages. Do not assign signals from memory because the LM324 family includes multiple package options with different pin arrangements. Verify every net against the exact 14-TSSOP ordering code before releasing artwork or assembling a board.
Is the LM324DTBR2G suitable for 5 V single-supply applications?
Yes, the LM324DTBR2G is suitable for a 5 V single-supply design because its documented operating range extends from 3 V to 32 V. According to the onsemi LM324 datasheet, the device includes true differential inputs and internal compensation for conventional closed-loop use. At 5 V, however, designers must still verify input common-mode limits, output swing into the intended load, and signal bandwidth. Those constraints determine whether the full input or output range is practical at the selected supply voltage.
How much bandwidth and slew rate does the LM324DTBR2G provide?
The LM324DTBR2G provides a 1 MHz gain-bandwidth product and a 0.6 V/µs slew rate. According to the onsemi LM324 datasheet and the indexed LM324 family specifications, these values position the device for general-purpose low-frequency amplification, buffering, and filtering. They are adequate for many sensor and control paths, but they do not make the part suitable for demanding video, high-speed communications, or precision ADC-driver applications where substantially wider bandwidth and faster edge rates are required.
What can replace the LM324DTBR2G on the same PCB?
The LM324DTBR2G can be replaced only by a confirmed 14-pin TSSOP LM324-family device with the same pin arrangement and compatible electrical limits. The cross-reference results identify LM324DTBR2 and LM324DTBG as onsemi comparison candidates in the LM324 family. Because suffix changes can affect qualification, shipping format, or ordering details, compare the complete ordering codes and electrical tables before substitution. A functional LM324 equivalent in another package is not a PCB drop-in replacement.
Is LM324DTBR2G the same as LM324DTBR2?
The LM324DTBR2G and LM324DTBR2 are closely related onsemi LM324 ordering codes, but the final suffix should not be ignored. The cross-reference results explicitly compare the two parts. According to the onsemi family documentation, both belong to the four-circuit, single-supply-capable LM324 product family; however, the customer must verify the exact package, qualification, marking, and shipping designation before treating one as a literal substitute for the other.
When should I choose the LM324DTBR2G instead of a lower-power amplifier?
Choose the LM324DTBR2G when four general-purpose amplifier channels are needed from a supply between 3 V and 32 V. According to the onsemi LM324 datasheet, its 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, true differential inputs, and internal compensation make it practical for conventional industrial and instrumentation signal paths. Select a lower-power amplifier instead when quiescent current is the dominant constraint and its narrower input, output, or bandwidth characteristics still satisfy the application.
Is LM324DTBR2G suitable for sensor signal conditioning?
Yes, the LM324DTBR2G is suitable for many low-frequency sensor signal-conditioning circuits. According to the onsemi LM324 datasheet, true differential inputs allow amplification of a sensor differential without first converting it to a single-ended signal, while internal compensation simplifies conventional closed-loop implementation. Its 5 mV input-offset voltage and 1 MHz gain-bandwidth product are appropriate for moderate-gain conditioning paths. Confirm the sensor output range, sensor impedance, common-mode voltage, and required noise performance before finalizing the design.
What is the best Texas Instruments equivalent for the LM324DTBR2G?
A Texas Instruments equivalent should be selected only after confirming an exact 14-pin TSSOP footprint and matching pin functions. The cross-reference material discusses LM324A-family devices, but it does not establish that every LM324A ordering code is pin-to-pin interchangeable with the LM324DTBR2G. Package naming conventions can differ even when both devices are described as 14-pin TSSOP. Use the Texas Instruments LM324A datasheet and pin tables for the final comparison, and treat any cross-brand choice as an engineering review item rather than an automatic substitution.
Where can I buy LM324DTBR2G online and check its current lead time?
Use the Request a Quote form on this page to ask for LM324DTBR2G pricing, stock, minimum order quantity, and current lead time. The indexed product listings confirm a commercial-market 14-TSSOP device from onsemi, but they do not provide a complete, dated quantity-break table for this exact suffix. A displayed starting price is not treated as a contractual one-piece price. The XAIPART quote team can confirm the exact MPN, packaging, delivery quantity, and shipment timing for your production schedule.
What is the current price of LM324DTBR2G?
The current unit price for LM324DTBR2G should be requested through the Request a Quote form on this page. The indexed listing states a starting price, but it does not present a complete quantity-break table tied to an explicit one-piece quantity, so that starting figure is excluded from the structured pricing data. A quotation can account for exact MPN, tape-and-reel quantity, order volume, destination, and requested delivery schedule without relying on a potentially stale online figure.
Is LM324DTBR2G in stock?
Current stock for the exact LM324DTBR2G should be confirmed through the Request a Quote form on this page. The available listing describes the part as a purchasable commercial component, but a distributor status can change independently of the component lifecycle and does not establish a guaranteed XAIPART inventory position. Include the required reel quantity, shipment destination, target date, and whether multiple sourcing locations are acceptable when requesting the quotation.
What is the input-offset voltage of the LM324DTBR2G?
The LM324DTBR2G has a specified input-offset voltage of 5 mV. According to the onsemi LM324 datasheet, this parameter describes the voltage difference required between the amplifier inputs to produce the specified output under defined conditions. Offset error can become important in high-gain, low-level sensing paths because it is amplified along with the wanted signal. For precision designs, evaluate the complete offset and drift conditions rather than relying only on the 5 mV headline value, and include system calibration where appropriate.
How should the LM324DTBR2G be bypassed for reliable single-supply operation?
Place the supply-bypass capacitors close to the LM324DTBR2G supply pins and keep the feedback and input routes short. According to the onsemi LM324 application guidance, stable operation with the internal compensation requires attention to feedback-loop design and output loading. Use the capacitor values recommended in the family datasheet for the intended supply range, and test the final board with realistic cable capacitance, sensor loading, and output load. Unused amplifier sections should be configured with a defined input connection.

داتای سەرچاوەی ئەندازیاری بۆ LM324DTBR2G — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM324DTBR2G when a design needs four general-purpose, low-frequency amplifier channels in a 14-pin TSSOP and can operate within a 3 V to 32 V supply range. Its true differential inputs, 1 MHz gain-bandwidth product, 0.6 V/µs slew rate, and internal compensation make it appropriate for sensor conditioning, current measurement, general filtering, and industrial interface circuits. LM324DTBR2 is the closest confirmed same-brand candidate when the final ordering suffix is acceptable after qualification review. LM324DTBG may suit the same footprint when its ordering and qualification details meet the production requirement, but its electrical table must be checked for the specific lot and grade. Do not substitute LM2902 or other LM324-family devices without verifying the 14-pin footprint and pin functions; dual amplifiers can require different board area or channel partitioning. For precision, rail-to-rail, micropower, or high-speed applications, choose a device specifically qualified for those requirements.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM324DTBR2 LM324DTBG
Package 14-TSSOP (0.173, 4.40 mm width) 14-TSSOP (0.173, 4.40 mm width) 14-TSSOP (0.173, 4.40 mm width)
Brand onsemi onsemi onsemi
Amplifier Type General Purpose General Purpose General Purpose
Number of Circuits 4 circuits 4 circuits 4 circuits

جیاکەرەوە سەرەکییەکان

  • Four general-purpose amplifier channels in one 14-pin TSSOP package (بەراورد بەLM2902DR)
  • Wide 32 V maximum supply-voltage capability (بەراورد بەLM2902DR)
  • True differential input architecture for direct differential measurement (بەراورد بەLM324DTBG)

تێبینییەکانی دیزاین

Place the supply-bypass capacitors directly beside the LM324DTBR2G supply and ground pins, and keep input and feedback traces short. The 1 MHz gain-bandwidth product can support moderate closed-loop gains, but long high-impedance traces increase pickup, phase delay, and sensitivity to parasitic capacitance. Route the differential input pair together, maintain a continuous ground reference, and avoid routing amplifier inputs beneath noisy switching nodes. For field-sensing boards, use guarding or differential layout so common-mode pickup does not convert into differential error at the 5 mV offset level.

The LM324DTBR2G supports a 3 V to 32 V supply range, but the usable signal range is constrained by the exact input common-mode limits, output swing, and load current in the onsemi datasheet. Before fixing the supply voltage, calculate the largest expected input and output excursion and add startup margin. Do not assume the full 32 V rating is usable at every amplifier node. Use local supply bypassing for all four channels, because a quad package can present a rapidly changing aggregate current even when each individual amplifier operates at low load.

Configure every unused amplifier section instead of allowing an input to float. Tie the non-inverting input to a defined reference near the output of the unused inverting input, and connect the output to the inverting input. Also verify whether the intended output is a source or sink and confirm that the selected feedback gain remains compatible with internal compensation. A 0.6 V/µs slew rate may become the limiting factor before the 1 MHz gain-bandwidth product when large-amplitude, low-frequency output transitions are required.

Account for the 5 mV input-offset specification in precision signal paths because closed-loop gain multiplies this error. For bridge sensors or current-shunt measurements, use the true differential input capability, calibrate systematic offset where appropriate, and avoid relying on thermal drift characteristics that are not established for the alternate ordering codes. Keep high-impedance summing nodes short because input bias current can create additional voltage error, especially when long external leads or sensor insulation resistances raise the effective source impedance.

Follow the manufacturer’s LM324 application guidance for feedback-network layout and output loading. Place the active feedback components near the relevant amplifier pins, and test with the actual cable, connector, and sensor capacitance because the 1 MHz bandwidth can interact with stray capacitance at higher closed-loop gains. Keep analog return current within the same ground system as the chip rather than sharing narrow paths with motors, relays, or switching converters. When an external connector reaches the amplifier input, add protection that does not introduce excessive leakage or unstable capacitance.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The exact LM324DTBR2G listings do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm the orderable part and compliance documents with onsemi before production release.

داتا پشتڕاستکراوەتەوە لە: 2026-11-06 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

LM324DTBR2G datasheet LM324DTBR2G datasheet pdf LM324DTBR2G pinout LM324DTBR2G equivalent LM324DTBR2G replacement LM324DTBR2G drop-in substitute LM324DTBR2G price LM324DTBR2G stock onsemi LM324DTBR2G LM324DTBR2G 14-TSSOP LM324DTBR2G 32V op amp LM324DTBR2G vs LM324DTBG

پێکهاتە و زاراوە پەیوەندیدارەکان

onsemi LM324DTBR2G LM324DTBR2 LM324DTBG LM324 series operational amplifier op amp quad operational amplifier single-supply operational amplifier true differential input general-purpose amplifier amplifier IC analog signal conditioning 3 V to 32 V power supply 5 mV input offset voltage 1 MHz gain-bandwidth product 0.6 V/µs slew rate internal compensation 14-TSSOP TSSOP package family surface-mount package tape and reel packaging industrial instrumentation sensor conditioning
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ