LM2902DTBR2 - Quad Op-Amp, 3-26V, 1MHz | onsemi | TSSOP-14
MPN: LM2902DTBR2 ✓ چالاکLM2902DTBR2 گشتی
A quad operational amplifier (op-amp) integrates four independent voltage amplifiers on a single silicon die. Each amplifier has a true differential input and can operate from a single power rail, simplifying design in systems that lack negative supplies. Quad op-amps form part of the wider analog signal-chain hierarchy: amplifier IC -> linear IC -> integrated circuit, and they are the workhorse building blocks for signal conditioning, active filtering, buffering, and transducer interface circuits.
Key features include the four-circuit integration in a space-saving 14-TSSOP footprint, single-supply operation down to 3V, and the classic LM324-family architecture with true differential inputs. The LM2902 grade is specified for automotive and industrial ambient temperature ranges, distinguishing it from the consumer-grade LM324 by its extended temperature rating and supply conditions.
Architecturally, the LM2902 family uses internally compensated bipolar circuitry, which guarantees unity-gain stability without external compensation components and allows outputs to swing close to the negative rail - a signature advantage in single-supply designs where ground-referenced signals must be reproduced. The four amplifiers share one supply pair, reducing board area and BOM count versus four single op-amps.
Typical applications include automotive sensor signal conditioning, industrial process control front ends, transducer amplifiers, active filters, summing amplifiers, and multichannel DC gain blocks in battery-powered or 12V/24V-rail systems where the wide 3-26V supply range removes the need for a dedicated regulator.
When designing with this device, remember that output swing is limited near the positive rail and the input common-mode range does not include the positive supply; for ground-referenced signals this is usually harmless, but designs requiring rail-to-rail performance should evaluate dedicated rail-to-rail op-amps instead.
This page synthesizes distributor availability, drop-in alternatives, comparison data, and practical design notes not found in the manufacturer datasheet, offering decision-grade information for sourcing and circuit design in one place.
جێگرەوەکانی جێگۆڕکێ بۆ LM2902DTBR2 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM2902DTBR2 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Amplifier Type, Input Offset Voltage, Input Type, Slew Rate.
LM2902DTBR2G
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →LM324DTBR2G
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2902PT
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2902DTBR2 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Configuration | Quad (4 circuits) |
| Amplifier Type | Standard / General Purpose Operational Amplifier |
| Supply Voltage Range (single supply) | 3 V to 26 V |
| Supply Voltage Range (dual supply) | up to ±13 V |
| Gain Bandwidth Product | 1 MHz |
| Input Offset Voltage | 7 mV |
| Input Type | True differential input |
| Output | Single-ended, swings close to negative rail |
| Compensation | Internally frequency compensated |
| پاکێج | 14-TSSOP |
| جۆری دامەزراندن | Surface Mount |
| Reel Packing | Tape and Reel (R2 packing code) |
ڕێکخستنی پینی LM2902DTBR2
| پین 1 | OUT1 — Output of amplifier 1 |
| پین 2 | IN1- — Inverting input, amplifier 1 |
| پین 3 | IN1+ — Non-inverting input, amplifier 1 |
| پین 4 | VCC — Positive supply voltage |
| پین 5 | IN2+ — Non-inverting input, amplifier 2 |
| پین 6 | IN2- — Inverting input, amplifier 2 |
| پین 7 | OUT2 — Output of amplifier 2 |
| پین 8 | OUT3 — Output of amplifier 3 |
| پین 9 | IN3- — Inverting input, amplifier 3 |
| پین 10 | IN3+ — Non-inverting input, amplifier 3 |
| پین 11 | GND/VEE — Ground (single supply) or negative supply (dual supply) |
| پین 12 | IN4+ — Non-inverting input, amplifier 4 |
| پین 13 | IN4- — Inverting input, amplifier 4 |
| پین 14 | OUT4 — Output of amplifier 4 |
بەکارهێنانە باوەکان
LM2902DTBR2 گونجاوە بۆ 6 بەکارھێنانs: Automotive Sensor Signal Conditioning, Industrial Process Control Front Ends, Active Filter Networks, Transducer and Bridge Amplifiers, Battery-Powered Portable Instrumentation, Comparator and Level-Detection Circuits.
Automotive Sensor Signal Conditioning
The LM2902DTBR2 fits automotive signal conditioning because the LM2902 grade is specified for the extended temperature and supply conditions found in vehicles, and its 3V to 26V supply range directly covers 12V battery rails with full-load transients up to 26V. Its four independent amplifiers let one TSSOP-14 package condition multiple sensors - such as throttle position, manifold pressure, or coolant level - with true differential inputs rejecting ground-bounce common-mode noise typical of automotive harnesses. Outputs swing close to ground, faithfully reproducing ground-referenced sensor signals into ADC inputs. In a typical circuit, each amplifier runs at a fixed non-inverting gain set by two resistors, with a 1 MHz bandwidth providing ample loop margin for DC and low-frequency sensor channels, while RC anti-alias filters ahead of the ADC set the overall noise bandwidth. For qualification-sensitive programs, confirm the exact ordering code's automotive grade documentation via the manufacturer datasheet.
پێشنیارکراو
Industrial Process Control Front Ends
Industrial controllers commonly run on 24V rails where the LM2902DTBR2's 26V maximum single-supply rating is a direct fit, eliminating an intermediate regulator for the analog front end. The quad configuration supports four independent channels - for example, 4-20mA receiver shunt amplification, thermocouple buffering, setpoint comparison, and alarm-level comparison - in one 14-TSSOP footprint, cutting board area and assembly cost versus four discrete amplifiers. Internally compensated unity-gain stability removes external compensation components, simplifying qualification of mixed-gain channel designs. The 7 mV input offset is acceptable for industrial tolerance bands, and the true differential inputs handle the large common-mode voltages generated by long cable runs when combined with input resistor networks. Outputs swinging to near ground let ADCs and comparators read full-scale low-level signals directly. Designers should keep input common-mode well below the positive rail and add input overvoltage protection for field-wired connections exposed to inductive transients.
پێشنیارکراو
Active Filter Networks
The LM2902DTBR2's internally compensated 1 MHz amplifiers support Sallen-Key and multiple-feedback active filters at audio and low-frequency industrial rates, where the closed-loop corner stays well below the gain-bandwidth product and Q-enhancement errors remain negligible. One TSSOP-14 package implements a complete four-pole filter cascade (two biquads per quad), each stage built from one amplifier plus a handful of resistors and capacitors. Because the outputs swing close to ground, single-supply filter biasing to mid-rail with a fourth amplifier as a virtual-ground buffer is a natural fit, using the remaining channels for cascaded filter poles. The 3V to 26V supply range allows the same filter design to migrate between 5V digital boards and 24V industrial systems without re-selection. At gains above 10, verify that the closed-loop bandwidth remains comfortable relative to 1 MHz, and keep source impedances low so the bipolar input bias current does not create excessive offset across the filter resistors.
پێشنیارکراو
Transducer and Bridge Amplifiers
Pressure, load-cell, and resistive bridge transducers benefit from the LM2902DTBR2's true differential inputs: two amplifiers form the classic three-op-amp instrumentation front end (input buffers plus difference amplifier), while the remaining two provide gain staging and output offsetting. Operating from a 3V to 26V single supply, the device can run directly from 12V or 24V system rails that also excite the bridge, reducing excitation-to-supply mismatch errors. Because the output swings close to ground, near-zero bridge outputs map close to 0V for direct ADC digitization; the 7 mV offset, referenced to the amplified gain, should be budgeted in the error calculation, and system calibration is commonly applied for precision spans. For ratiometric designs, powering the bridge and reference from the same rail cancels supply drift. Add series input resistors and clamp diodes at field terminals to protect the amplifier inputs from surge events during wiring faults or hot-plugging of transducer cables.
پێشنیارکراو
Battery-Powered Portable Instrumentation
The LM2902DTBR2 belongs to the low-power LM324 family, and its ability to run from a single supply as low as 3V makes it suitable for battery-operated instruments powered by two alkaline cells or a single lithium cell, down to the low end of its 3V to 26V supply span. The quad integration halves the amplifier count versus single-op-amp designs, cutting quiescent power and PCB area, which directly extends battery life in portable meters, testers, and dataloggers. Ground-sensing outputs reproduce near-zero sensor levels without a negative rail, so the entire analog chain runs from one battery. Designers should budget the supply current across four amplifiers at the battery's end-of-life voltage, verify gain-bandwidth margin at 1 MHz against the signal band, and consider a supply supervisor for brownout protection as the cell discharges toward 3V. For ultra-long-life products, compare modern micropower quads with per-amplifier shutdown against this classic family's sourcing advantage.
پێشنیارکراو
Comparator and Level-Detection Circuits
Beyond amplification, LM324-family quads are widely used as low-cost comparators: two channels monitor threshold crossings while remaining channels provide the reference buffering and hysteresis feedback. The LM2902DTBR2's wide 3V to 26V single-supply operation suits 12V and 24V industrial level detection, such as liquid-level switches, over-voltage flags, and window comparators on battery charger rails. With a pull-up to the positive rail at the output, the near-ground output swing yields clean logic transitions when the open-loop differential drives the output to its limits. Designers should add positive feedback resistors for a few millivolts of hysteresis to prevent chatter on slow-moving analog signals, and should note the device is an op-amp, not a dedicated comparator, so response time and saturation recovery are slower than purpose-built parts - acceptable for supervisory functions, but not for fast edge detection. Its 1 MHz bandwidth bounds switching rates to the tens of kilohertz in practice.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM2902DTBR2 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2902DTBR2G | LM324DTBR2G | LM2902PT |
|---|---|---|---|---|
| Package | 14-TSSOP | 14-TSSOP - same | 14-TSSOP - same | TSSOP-14 - same |
| Brand | onsemi | onsemi | onsemi | STMicroelectronics |
| Supply Voltage Range | 3 V to 26 V | 3 V to 26 V | 3 V to 32 V (commercial grade) | 3 V to 26 V |
| Bandwidth | 1 MHz | 1 MHz | 1 MHz | 1 MHz |
| Amplifier Circuits | 4 | 4 | 4 | 4 |
| Grade / Temperature Focus | Automotive/industrial (LM2902) | Automotive/industrial (LM2902) | Commercial (LM324) | Automotive/industrial (LM2902) |
| Mounting Type | Surface Mount | Surface Mount | Surface Mount | Surface Mount |
جیاکەرەوە سەرەکییەکان
- Automotive/industrial grade in the classic quad family (بەراورد بەLM324DTBR2G)
- onsemi sourcing continuity with Pb-free variant (بەراورد بەLM2902DTBR2G)
- Honest trade-off: 7 mV offset vs precision quads (بەراورد بەTS934IDT)
تێبینییەکانی دیزاین
The LM2902DTBR2 accepts a 3V to 26V single supply, but absolute maximum ratings on the onsemi datasheet are higher than the recommended range - never rely on transients staying within recommended limits without protection. On 24V industrial rails, add a series resistor and Zener or TVS clamp ahead of the supply pin to absorb surges. Remember pin 11 doubles as GND in single-supply use and VEE in dual-supply use; incorrect polarity at this pin on power-up is a classic field-failure cause. Estimated: at four amplifiers of the low-power family's typical per-amp current, total quiescent draw stays in the milliamp range, so supply routing traces of 0.2 mm width are generally adequate.
The input common-mode range of this bipolar family does not include the positive rail; keeping inputs at least a few volts below VCC prevents phase-reversal-style misbehavior. Outputs swing close to, but not to, the positive rail - budget headroom when interfacing to ADCs expecting rail-to-rail swing. With a 7 mV input offset and nonzero bias current, keep DC source impedances below roughly 10 kilo-ohms (estimate: 7 mV offset dominates unless resistor values create comparable IR drops) and place a small series resistor at each input for protection. Add 0.1 microfarad local decoupling from VCC (pin 4) to GND (pin 11), placed within a few millimeters of the pins.
Do not substitute this part into circuits designed for rail-to-rail op-amps: signals near the positive supply will not be reproduced, and outputs saturating near VCC have long recovery times. When using channels as comparators, add hysteresis - without it, slow analog ramps cause output chatter and EMI. When qualifying drop-in replacements (LM2902DTBR2G, LM324DTBR2G, LM2902PT), verify the temperature grade on the specific supplier datasheet, not just the package code, since LM324 commercial grade and LM2902 automotive grade differ in range even though pinouts and the 14-TSSOP footprint are identical.
زانیاری پابەندبوون
Compliance status should be confirmed against the onsemi product page for the exact ordering code; onsemi typically supplies Pb-free and RoHS declarations for LM2902 family parts.