Texas Instruments

LM339ADR - Quad Differential Comparator, SOIC-14 | Texas Instruments

MPN: LM339ADR ✓ چالاک
2 V to 36 V Vdss 3 nA Id 14-SOIC Package
MOQ: 1 |

LM339ADR گشتی

The Texas Instruments LM339ADR is a quad differential comparator with four independent voltage comparators, open-collector outputs, and a wide single-supply operating range of 2V to 36V, housed in a 14-pin SOIC package.

A differential comparator is an analog component that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier IC family of analog signal-chain devices, positioned between operational amplifiers and dedicated level detectors in the system hierarchy. Unlike an op-amp, a comparator is designed for fast, saturated switching between two output states rather than linear amplification, making it the standard building block for threshold detection, zero-crossing detection, and analog-to-digital conversion front ends.

Key features of the LM339ADR include a common-mode input voltage range that extends down to ground (V-), which permits sensing signals referenced to the negative rail without additional level shifting. The differential input voltage range equals the maximum-rated supply voltage of 36V, and the open-collector outputs can sink current to drive TTL, MOS, and CMOS logic directly while allowing wired-OR connections. Input bias current is low, on the order of nanoamperes (approximately 3nA per LCSC device data), keeping input source impedance requirements modest.

Technically, the LM339 family uses a PNP differential input stage that allows operation from a single supply as low as 2V, or from dual supplies as long as the total supply difference is 2V to 36V and VCC is at least 1.5V more positive than the input common-mode voltage. Per the TI LM339A product page, the B-version is a drop-in replacement for the LM239, LM339, and LM2901, and the device features a low output saturation voltage for efficient logic-level interfacing.

Typical applications include threshold detectors in power-supply supervision, oscillators and multivibrators, window comparators in test equipment, and level shifting between analog sense circuits and digital controllers. The four comparators per package reduce board area and BOM line items in multi-channel monitoring designs.

A key design consideration is that the open-collector outputs require external pull-up resistors; the LM339 cannot source current, and unused comparators should have inputs tied to defined rails to prevent oscillation.

This page synthesizes distributor availability data, pin-compatible alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet alone.

جێگرەوەکانی جێگۆڕکێ بۆ LM339ADR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM339ADR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Comparator Type, Output Compatibility, Supply Configuration, Differential Input Voltage Range.

Texas Instruments
Comparator Type: Quad differential comparator
Output Compatibility: TTL, CMOS, and MOS compatible
Supply Configuration: Single or split supply
بەراوردکردن لەگەڵ LM339ADR →
Texas Instruments
Package: 14-pin SOIC
Comparator Type: General-purpose differential comparator
Output Compatibility: TTL, MOS, and CMOS
بەراوردکردن لەگەڵ LM339ADR →
Texas Instruments
Package: 14-pin SSOP
Comparator Type: Quad differential voltage comparator
Differential Input Voltage Range: Equal to the maximum-rated supply voltage, up to ±38V
بەراوردکردن لەگەڵ LM339ADR →
ON Semiconductor
Package: 14-pin SOIC
Supply Configuration: Single supply
بەراوردکردن لەگەڵ LM339ADR →
Texas Instruments
Package: 14-SOIC, 3.90 mm width
Comparator Type: Quad differential comparator
Output Compatibility: TTL, MOS, and CMOS compatible
بەراوردکردن لەگەڵ LM339ADR →
onsemi
Comparator Type: General Purpose
Output Compatibility: CMOS and TTL
Supply Configuration: Single
بەراوردکردن لەگەڵ LM339ADR →
Texas Instruments
Package: 14-pin SOIC
Comparator Type: Quad differential comparator
بەراوردکردن لەگەڵ LM339ADR →
Texas Instruments
Comparator Type: Differential, general purpose
Differential Input Voltage Range: Up to ±38 V
بەراوردکردن لەگەڵ LM339ADR →
Texas Instruments
Package: 14-pin SOIC, PDSO14
Comparator Type: Quad differential voltage comparator
Supply Configuration: Single supply or dual supply
بەراوردکردن لەگەڵ LM339ADR →

LM339AD

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 14-SOIC
4 · General-purpose differential comparator · Open-collector · 14-pin SOIC · Up to 38 V · ±38 V · Includes ground · 0.37 mV

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM339ADBR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 14-SOIC
Quad differential voltage comparator · 4 independent channels · 2V to 30V · 38V · Open-collector · 0.37mV · 3.5nA · 200µA per comparator

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM239AD

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 14-SOIC
Quad differential comparator · 4 channels · 4 independent comparators · Open-collector · Single or split supply · 14-SOIC · Surface mount · Up to ±38 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM139AD

✅ جێگرەوەی ڕاستەوخۆ
📦 14-SOIC
military/extended-temperature grade, same SOIC-14 footprint and quad open-collector architecture

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM339ADT

✅ جێگرەوەی ڕاستەوخۆ
📦 14-SOIC
ST industry-standard LM339 in 14-SO, same open-collector quad comparator, output compatible with CMOS/DTL/ECL/MOS/TTL

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

LM339NSRG4

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SO-14
Quad differential voltage comparator · 4 channels · Single supply or dual supply · 30 V · 32 V · 0.8 mA · Independent of supply voltage · 9 mV

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM339ADR زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

کارکردن Quad differential comparator
Number of Channels 4
جۆری دەرچوون Open-collector
Supply Voltage Range (Single) 2 V to 36 V
Differential Input Voltage Range Up to maximum-rated supply voltage (36 V)
Common-Mode Input Voltage Range Includes ground (V-)
Input Bias Current 3 nA
Output Compatibility TTL, MOS, CMOS, DTL, ECL
Output Saturation Voltage Low (per TI product page)
پاکێج 14-SOIC
جۆری دامەزراندن Surface Mount
Manufacturer Part Number LM339ADR
Manufacturer Texas Instruments
پۆل Comparators (Standard General Purpose)

ڕێکخستنی پینی LM339ADR

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
پین 1 OUT2 — Open-collector output of comparator 2
پین 2 OUT1 — Open-collector output of comparator 1
پین 3 VCC — Positive supply voltage
پین 4 IN1- — Inverting input, comparator 1
پین 5 IN1+ — Non-inverting input, comparator 1
پین 6 IN2- — Inverting input, comparator 2
پین 7 IN2+ — Non-inverting input, comparator 2
پین 8 IN3- — Inverting input, comparator 3
پین 9 IN3+ — Non-inverting input, comparator 3
پین 10 IN4- — Inverting input, comparator 4
پین 11 IN4+ — Non-inverting input, comparator 4
پین 12 GND — Ground / negative supply (V-)
پین 13 OUT4 — Open-collector output of comparator 4
پین 14 OUT3 — Open-collector output of comparator 3

بەکارهێنانە باوەکان

LM339ADR گونجاوە بۆ 6 بەکارھێنانs: Power Supply Undervoltage/Overvoltage Supervision, Threshold Detection and Window Comparators, Oscillators and Relaxation Multivibrators, Zero-Crossing and Line-Frequency Detection, Battery-Powered and Portable Monitoring, Analog-to-Digital Level Shifting and Logic Interfacing.

⚡

Power Supply Undervoltage/Overvoltage Supervision

The LM339ADR is a natural fit for power-rail supervision because its common-mode input range extends to ground, letting each comparator directly monitor a divider from the rail being watched without negative supply or level-shifting circuitry. With four comparators in one 14-SOIC, a single package can implement undervoltage, overvoltage, and power-good thresholds for two independent rails, each output pulling down a logic line when the threshold is crossed. The 2V to 36V supply range means the same design scales from 5V logic supervision to 24V industrial bus monitoring. Adding a positive-feedback resistor of roughly 100k ohm introduces hysteresis that prevents chatter on slowly collapsing rails, and the low output saturation voltage keeps the fault flag valid for TTL or CMOS monitoring inputs.

🔧

Threshold Detection and Window Comparators

For sensor-conditioning circuits that must flag when a signal enters or leaves a defined band, the LM339ADR's four channels allow one package to build a full window comparator plus a fault latch. Each comparator compares a conditioned sensor voltage against a resistor-divider or reference threshold, and the open-collector outputs can be wire-ORed so a single interrupt line reports any out-of-window condition. Input bias current of approximately 3nA permits high-impedance divider networks in the megohm range, which matters for battery-powered monitoring where divider current dominates standby draw. Because the differential input voltage range extends to the 36V maximum-rated supply, large sensor swings can be compared directly without front-end attenuation in most 12V and 24V systems.

🔧

Oscillators and Relaxation Multivibrators

The LM339ADR builds reliable RC relaxation oscillators: one comparator toggles a capacitor between two thresholds set by a divider, producing a square wave whose frequency is set by the RC network. Open-collector outputs discharge the timing capacitor sharply, giving crisp edges even at low supply voltages down to 2V, which suits low-voltage clock generation in battery products. The remaining three comparators in the package can serve as duty-cycle shaping, phase detection, or lock-detect functions in the same footprint. Typical circuits run from a few kilohertz to hundreds of kilohertz; frequency stability follows the RC components rather than the IC, so using NP0/C0G capacitors keeps drift low. The ground-referenced common-mode range simplifies single-supply timing-node biasing.

⚡

Zero-Crossing and Line-Frequency Detection

Mains-synchronized systems such as triac dimmers, solid-state relays, and power-factor correction controllers need a clean logic pulse at every AC line zero crossing. The LM339ADR performs this directly: the scaled line voltage is compared against mid-point or ground bias, and the open-collector output pulls low on each crossing, delivering a sharp edge to a microcontroller interrupt pin. The 36V differential input rating tolerates the divided line-amplitude swings and transient overshoot typical of transformer-less sensing networks. Because the common-mode range includes ground, the sensing node can sit at the virtual ground of a resistor bridge without exceeding input limits. One package handles zero-cross detection for both half-cycles plus a phase-loss comparison for fault monitoring.

📱

Battery-Powered and Portable Monitoring

In portable instruments, the LM339ADR provides multi-channel battery and signal monitoring from a supply as low as 2V, allowing operation down to near end-of-life cell voltage. The nanoampere-class input bias current lets designers use high-value (megohm) sensing dividers, so the monitoring front end itself draws negligible quiescent current compared with the load. Four comparators per 14-SOIC cover battery-undershoot warning, charge-complete detection, reverse-polarity flagging, and an analog limit alarm without extra ICs. Open-collector outputs pull up to the microcontroller's rail even when the comparator supply differs, easing level integration across power domains. Wire-OR outputs also let a single wake-up interrupt line aggregate all fault conditions to minimize controller polling.

🖥️

Analog-to-Digital Level Shifting and Logic Interfacing

The LM339ADR bridges analog sense circuitry to digital controllers: its open-collector output pulls up to any logic rail from 2V to 36V, so a comparator running on a 24V industrial supply can directly drive a 3.3V or 5V MCU input, provided the pull-up references the logic rail. Output compatibility spans TTL, MOS, CMOS, DTL, and ECL per the TI product page, making it a universal interface element. In ADC front ends, comparators handle over-range and polarity flagging ahead of the converter, protecting the input path. Low output saturation voltage keeps the logic-low level well inside TTL and CMOS threshold specifications even at moderate sink currents, and wired-OR output configurations let several comparisons share one microcontroller interrupt line.

کورتەی بەرهەمە پێشنیارکراوەکان

TL431AIDBZR Texas Instruments بەکارهێنراوە لە: Power Supply Undervoltage/Overvoltage Supervision LM393ADR Texas Instruments بەکارهێنراوە لە: Power Supply Undervoltage/Overvoltage Supervision REF5025AIDR Low-noise series reference for threshold setting بەکارهێنراوە لە: Threshold Detection and Window Comparators LM339ADR Texas Instruments بەکارهێنراوە لە: Threshold Detection and Window Comparators NE555DR Texas Instruments بەکارهێنراوە لە: Oscillators and Relaxation Multivibrators TLV431BQDBZR Adjustable shunt reference for threshold bias بەکارهێنراوە لە: Oscillators and Relaxation Multivibrators MOC3063M Opto-triac driver for zero-cross switching بەکارهێنراوە لە: Zero-Crossing and Line-Frequency Detection TL431ACDBZR Texas Instruments بەکارهێنراوە لە: Zero-Crossing and Line-Frequency Detection TPS7A02QDRVR Ultra-low-IQ LDO for portable rails بەکارهێنراوە لە: Battery-Powered and Portable Monitoring TL331BQDBZR Single comparator for low-channel-count designs بەکارهێنراوە لە: Battery-Powered and Portable Monitoring ADS1110A0IDBVR 16-bit delta-sigma ADC for the analog channel بەکارهێنراوە لە: Analog-to-Digital Level Shifting and Logic Interfacing SN74LVC1G17DBVR Texas Instruments بەکارهێنراوە لە: Analog-to-Digital Level Shifting and Logic Interfacing
What is the LM339ADR?
The LM339ADR is a Texas Instruments quad differential comparator IC containing four independent voltage comparators with open-collector outputs in a 14-pin SOIC package. It operates from a single 2V to 36V supply or from dual supplies as long as the total difference is 2V to 36V, and its common-mode input range includes ground. According to the TI LM339A product page, the device is designed for general-purpose comparator applications and is output-compatible with TTL, MOS, and CMOS logic.
What is the supply voltage range of the LM339ADR?
The LM339ADR operates from a single supply over a wide range of 2V to 36V. Dual-supply operation is also possible as long as the difference between the two supplies is 2V to 36V and VCC is at least 1.5V more positive than the input common-mode voltage. This wide range lets one comparator family serve 5V logic systems, 12V automotive rails, and 24V industrial monitoring circuits without redesign. Source: TI LM339A product page.
Does the LM339ADR require pull-up resistors on its outputs?
Yes, the LM339ADR outputs are open-collector and require external pull-up resistors to the desired logic rail. The comparators can only sink current; the pull-up sets the logic-high level, which lets the same device interface with 5V TTL, CMOS, or other voltage domains. A typical pull-up is 3k ohm to 15k ohm depending on speed and fan-out requirements. Open-collector outputs also permit wired-OR configurations where multiple comparator outputs share one pull-up. Source: TI LM339A product page.
What is the difference between LM339ADR and LM239AD?
The LM239AD is the automotive/extended-temperature-grade member of the same LM339 family in the same SOIC-14 package with an identical pinout, while the LM339ADR is the standard commercial/industrial grade. Both are quad differential comparators with open-collector outputs and the same electrical core specifications. Per TI's product page, the family is designed so the B-version and related grades (LM239, LM339, LM2901) are drop-in interchangeable, so substitution is mainly a matter of the temperature grade your application requires.
What is the difference between LM339ADR and LM139AD?
The LM139AD and LM339ADR share the same die family, open-collector quad comparator architecture, and SOIC-14 pinout; they differ primarily in temperature grade, with the LM139 being the military/extended-temperature version and the LM339 the standard version. Distributor comparison listings (Findchips) group LM139AD and LM339ADR as related devices. Choose the LM139AD only when extended-temperature qualification is explicitly required; otherwise the LM339ADR is the lower-cost standard choice.
Can LM339ADT (STMicroelectronics) replace the LM339ADR?
Yes, the STMicroelectronics LM339ADT is a pin-compatible replacement for the LM339ADR. DigiKey lists the LM339ADT as a comparator in the same 14-SO package with open-collector outputs compatible with CMOS, DTL, ECL, MOS, and TTL - the same interface set as the TI part. Because both are industry-standard LM339 quad comparators in SOIC-14, the substitution is drop-in on the same PCB footprint; verify the output pull-up value and switching-speed expectations against the ST datasheet during qualification.
What is the best drop-in replacement for the LM339ADR?
The best drop-in replacements are same-family TI parts in the same SOIC-14 package: LM339AD (same die, standard reel packaging variant), LM339ADBR (same quad comparator, per TI's related-part listings), LM239AD (extended temperature grade), and LM139AD (military grade). Cross-brand, the STMicroelectronics LM339ADT is a pin-to-pin equivalent in 14-SO. All share the open-collector quad architecture and common-mode range including ground, so no PCB rework is needed. Source: TI LM339A product page and distributor cross listings.
Is the LM339ADR suitable for single-supply 5V operation?
Yes, the LM339ADR operates from a single 5V supply, well within its 2V to 36V specified range. Its common-mode input voltage range extends to the negative rail (ground), so inputs can sense signals referenced to 0V on a single 5V rail. The open-collector outputs pull up to the same 5V rail for direct TTL or CMOS interfacing. For signals near the positive rail, note the input common-mode range upper limit - keep inputs at least 1.5V below VCC per the dual-supply operating condition stated on the TI product page.
What are the key specifications of the LM339ADR that engineers should know?
The LM339ADR provides four independent comparators with open-collector outputs in a 14-SOIC package. Key numbers: single-supply operation from 2V to 36V, differential input range up to the 36V maximum-rated supply, common-mode input range including ground, approximately 3nA input bias current, low output saturation voltage, and direct compatibility with TTL, MOS, and CMOS logic. These figures come from the TI LM339A product page and LCSC device data. The four-channel integration is the main reason it remains a standard for multi-threshold monitoring.
Where can I download the LM339ADR datasheet PDF?
The LM339ADR datasheet PDF is available from Texas Instruments on the official TI product page at ti.com/product/LM339, and distributor datasheet archives such as alldatasheet.com host the same TI document (the LM339ADR datasheet is listed there as 19 pages, 518 KB). Always prefer the TI.com copy for the latest revision. XAIPART also links the manufacturer datasheet directly from this product page, so you can open the PDF without leaving the site.
Where can I find the LM339ADR pinout?
The complete LM339ADR pinout for the 14-pin SOIC package is shown in the pin diagram on this page and in the TI LM339 datasheet. In brief: pin 1 is OUT2, pin 2 is OUT1, pin 3 is VCC, pins 4-7 are IN1-/IN1+/IN2-/IN2+, pins 8-11 are IN3-/IN3+/IN4-/IN4+, pin 12 is GND, pin 13 is OUT4, and pin 14 is OUT3. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks and verifying footprint connections.
How much does the LM339ADR cost and where can I buy it?
The LM339ADR is a low-cost, high-volume commodity comparator; distributor listings show single-unit pricing on the order of ten US cents at LCSC. For exact, current XAIPART pricing, quantity breaks, and lead time, use the Request a Quote form on this page - quotes are returned with firm availability and packaging options. Because the part is active and produced in volume by TI, long-term supply is not a concern, and standard tape-and-reel quantities are available for production orders.
What is the lead time and stock status of the LM339ADR?
The LM339ADR is an active Texas Instruments product in mass production, and distributors report it in stock and shipping immediately (DigiKey lists it as ships today; LCSC reports tens of thousands of units on hand). Standard lead time is therefore stock-driven rather than factory-driven for most quantities. For current XAIPART stock levels, reel quantities, and delivery schedules, submit the Request a Quote form on this page and our team will confirm availability and shipping terms.
Is the LM339ADR the same as the LM339?
The LM339ADR is the SOIC-14 surface-mount packaging of the industry-standard LM339 quad differential comparator. The base LM339 designation covers the die and function; the suffix encodes package, reel, and temperature details - ADR specifically means the A-enhanced version in a 14-SOIC with tape-and-reel packing. Functionally all LM339 orderable variants provide four open-collector comparators with a 2V to 36V supply range; only package and grade differ, per the TI ordering-information table.
What design considerations apply when using the LM339ADR?
Three considerations matter most. First, every open-collector output needs a pull-up resistor to the logic rail - the device cannot source current. Second, keep inputs within the common-mode range: down to ground but at least 1.5V below VCC for guaranteed specification, per the TI product page operating conditions. Third, tie unused comparator inputs to defined rails and add a small amount of hysteresis (a positive feedback resistor) on slow-moving signals to prevent output chatter near the threshold. Ground bounce on shared open-collector lines also warrants short return paths.

داتای سەرچاوەی ئەندازیاری بۆ LM339ADR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM339ADR when you need four general-purpose comparators in one SOIC-14 package for single-supply threshold detection between 2V and 36V, with outputs that must interface to TTL, MOS, or CMOS logic through pull-up resistors. Select LM239AD instead when the application is automotive or extended-temperature - it is the same die family and pinout with a wider grade. Select LM139AD for military-temperature requirements on the same footprint. Choose LM339ADT (STMicroelectronics) when TI supply is constrained; it is an industry-standard pin-compatible LM339 in 14-SO. Choose LM339NSRG4 if your footprint already matches the SO-14 wide-body variant. If you need only one or two comparators, the TL331B or LM393 reduce cost and quiescent current; reserve the quad for designs that genuinely use three or more channels. All options require external output pull-ups and benefit from added hysteresis on slow signals.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM339AD LM239AD LM139AD LM339ADT LM339NSRG4
Package 14-SOIC 14-SOIC - same 14-SOIC - same 14-SOIC - same 14-SO - same SO-14 (wide) - same footprint family
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments STMicroelectronics Texas Instruments
Number of Comparators 4 4 4 4 4 4
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector Open-collector
Supply Voltage Range 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V
Common-Mode Range Includes Ground Yes Yes Yes Yes Yes Yes
Logic Compatibility TTL, MOS, CMOS TTL, MOS, CMOS TTL, MOS, CMOS TTL, MOS, CMOS CMOS, DTL, ECL, MOS, TTL TTL, MOS, CMOS

جیاکەرەوە سەرەکییەکان

  • Four comparators per SOIC-14 package (بەراورد بەTL331B (single comparator))
  • Common-mode input range includes ground (بەراورد بەGeneric high-side-input comparators)
  • Broad same-footprint grade coverage within the family (بەراورد بەLM239AD / LM139AD)

تێبینییەکانی دیزاین

The most frequent LM339 design error is omitting the output pull-up resistor. All four outputs are open-collector and can only sink current; without a pull-up to the desired rail the output never reaches a valid logic-high state. Choose the pull-up value for speed versus sink current: 3k ohm gives fast edges but demands more output sink capability, while 10k to 15k ohm is adequate for supervision flags. Also tie unused comparator inputs to defined rails - floating inputs on high-gain comparators can self-oscillate and inject noise into neighboring channels.

Add hysteresis to any comparator handling slow-moving analog signals. A positive-feedback resistor from output to the non-inverting input (typically 100k ohm to 1M ohm, sized against the source impedance) creates a few tens of millivolts of hysteresis that prevents output chatter as the input crosses the threshold. Without it, noisy signals produce multiple transitions that corrupt microcontroller interrupts. Keep the threshold divider impedance below a few hundred kilohms given the approximately 3nA input bias current, which produces offset error equal to bias current times source resistance.

Place a 100nF ceramic decoupling capacitor directly across VCC (pin 3) and GND (pin 12) of the SOIC-14, with the loop as short as possible. Because all four comparators share the supply and ground pins, large open-collector sink currents from simultaneous switching can bounce the ground reference; use a solid ground plane and route the VCC trace with adequate width. Keep high-impedance input traces short and guard them with ground if they run near switching outputs, since the megohm-level divider networks used with nanoampere bias currents are sensitive to leakage and coupling.

Estimated: the LM339 family draws its supply current largely from output sink current, not just quiescent bias - each output that is low sinks the pull-up resistor current continuously (for a 10k ohm pull-up to 5V that is 0.5 mA per asserted output). Sum the worst-case number of simultaneously low outputs when budgeting supply current in battery designs, and prefer higher pull-up values for flags that stay asserted for long periods.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance status was not stated in the retrieved listings; confirm RoHS/REACH status on the official TI product page or via quote request.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lm339adr datasheet LM339ADR datasheet pdf LM339ADR pinout LM339ADR equivalent LM339ADR replacement LM339ADR cross reference LM339ADR vs LM339ADT Texas Instruments LM339ADR LM339 quad comparator SOIC-14 LM339ADR price stock LM339 application circuit LM339 open collector pull-up resistor

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM339ADR LM339 LM339A LM239AD LM139AD LM339ADT STMicroelectronics quad differential comparator comparator amplifier IC open-collector output SOIC-14 small outline package family surface mount TTL CMOS input bias current common-mode input voltage range output saturation voltage single-supply operation RoHS power supply supervision zero-crossing detection window comparator
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ