LM339DT - Low-Power Quad Voltage Comparator | STMicroelectronics
MPN: LM339DT ✗ کۆتایی ژیانLM339DT گشتی
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The LM339 belongs to the comparator hierarchy, where a comparator IC converts an analog voltage relationship into a logic-level decision. Four independent channels allow one package to perform four separate comparisons, reducing component count when a system requires several monitoring or control functions.
The principal benefits of the LM339DT are its low operating power, wide supply-voltage range, and open-collector output architecture. Each output can sink current from a pull-up network, allowing multiple comparator outputs to share a bus for wired-OR operation. The open-collector structure also permits designers to select the external pull-up voltage and logic family, making the device useful in mixed-voltage systems where fixed push-pull outputs would be less flexible.
The four internal channels have independent input and output stages but share a common ground reference. Because output current is returned through the open-collector transistor rather than a push-pull output stage, external pull-up resistors are required for normal digital operation. Input common-mode range, differential input limits, response time, output saturation voltage, and input offset voltage must be checked against the actual sensing point and supply conditions before finalizing a circuit.
Typical applications include industrial sensor interfaces, battery and power-supply monitoring, window or threshold comparators, relay-control logic, level-crossing detection, and general-purpose embedded control. A single package can implement four independent monitoring channels while preserving the low component count and straightforward hookup of a quad comparator.
PCB design should keep comparator inputs away from high-current switching nodes and route the four channels in a way that minimizes common-impedance coupling. Place input and pull-up components close to the device, maintain a low-impedance ground reference, and verify that input transients do not exceed the absolute maximum ratings. The open-collector outputs require suitable pull-up resistors, and any external LED or relay load must include appropriate current limiting or drive circuitry.
This page combines the LM339DT specifications, verified manufacturer and distributor links, drop-in replacement guidance, comparison parameters, and practical PCB and circuit-design notes. It is intended to help engineers identify whether the quad open-collector architecture satisfies the voltage, logic-interface, layout, and sourcing requirements of a new design.
جێگرەوەکانی جێگۆڕکێ بۆ LM339DT — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM339DT (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Comparator Type, Supply Current, Logic Compatibility, Response Time.
LM239DR
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2901DR
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM339DR
✅ جێگرەوەی ڕاستەوخۆ✓ بەردەستە
$0.0738 / یەکە
بینینی داتاشیت →LM339DT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM339DR2G
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM339DT زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Quad differential voltage comparator |
| Number of Channels | 4 independent channels |
| Supply Voltage Range | 2 V to 36 V |
| جۆری دەرچوون | Open collector |
| Logic Compatibility | CMOS, DTL, ECL, MOS, and TTL |
| پاکێج | 14-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Input Offset Voltage for LM339A, LM239A, and LM139A | 2 mV maximum |
ڕێکخستنی پینی LM339DT
| پین 1 | OUT1 — Comparator 1 open-collector output |
| پین 2 | IN1- — Comparator 1 inverting input |
| پین 3 | IN1+ — Comparator 1 non-inverting input |
| پین 4 | GND — Ground connection |
| پین 5 | IN2+ — Comparator 2 non-inverting input |
| پین 6 | IN2- — Comparator 2 inverting input |
| پین 7 | OUT2 — Comparator 2 open-collector output |
| پین 8 | OUT3 — Comparator 3 open-collector output |
| پین 9 | IN3- — Comparator 3 inverting input |
| پین 10 | IN3+ — Comparator 3 non-inverting input |
| پین 11 | GND — Ground connection |
| پین 12 | IN4+ — Comparator 4 non-inverting input |
| پین 13 | IN4- — Comparator 4 inverting input |
| پین 14 | OUT4 — Comparator 4 open-collector output |
بەکارهێنانە باوەکان
LM339DT گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Threshold Detection, Battery Voltage Monitoring, Power Supply Overvoltage Detection, Relay and Control Interlocking, Logic Level Translation, Window Comparator and Signal Crossing Detection.
Industrial Sensor Threshold Detection
The LM339DT fits industrial sensor interfaces because it provides four independent comparison channels, a 2 V to 36 V supply range, and open-collector outputs in one 14-pin SOIC package. A scaled sensor signal can be compared with a stable reference at each channel, producing separate high, low, or fault indications. Using four channels consolidates level supervision without forcing a common output voltage. The external pull-up network can match the voltage levels of the controller, while the common ground and input limits must be checked against the sensor source impedance and industrial noise environment.
پێشنیارکراو
Battery Voltage Monitoring
The LM339DT is useful for battery-pack threshold monitoring because four independent channels can supervise different voltage levels, such as minimum, maximum, and intermediate state-of-charge boundaries. Each channel compares a divided battery voltage against a reference, and its open-collector output can pull down a digital status line or inhibit a load switch. The sensing divider should limit standby current and account for resistor tolerance and temperature drift. The 2 V to 36 V device supply does not by itself guarantee that every battery input remains inside the comparator common-mode range, so the complete sensing circuit requires validation.
پێشنیارکراو
Power Supply Overvoltage Detection
The LM339DT can supervise a power rail in industrial or communications equipment by comparing a scaled supply voltage with a reference and generating an open-collector fault indication. Four channels allow separate monitoring of positive, negative, auxiliary, or sequenced rails. The 2 V to 36 V operating range supports many 24 V industrial systems, while the open-collector output permits a pull-up to the local fault-controller logic. Designers must still verify input common-mode limits, response time, output timing, and behavior during supply startup. A small RC filter at the divider may reduce false trips, but its delay must remain compatible with the protected system.
پێشنیارکراو
Relay and Control Interlocking
The LM339DT is appropriate for interlock and relay-control logic because open-collector outputs can directly interface with suitable transistor or logic-driver stages and can share a fault bus. Four channels can evaluate independent permission, limit, or sequencing conditions before enabling a load. A pull-up resistor establishes the positive logic state, while the comparator sinks current when a condition is violated. The output sink rating must match the pull-up current, and inductive loads require flyback protection. Because the four channels share the package ground, layout should keep high-current relay returns away from the comparator reference to prevent ground bounce from changing decision thresholds.
پێشنیارکراو
Logic Level Translation
The LM339DT can translate between logic domains because its open-collector output does not impose a fixed high-side voltage. Pull each output to the voltage required by the destination family, allowing CMOS, MOS, or TTL-compatible interfacing as specified for the device. This arrangement is useful when a legacy controller cannot directly accept the voltage generated by newer peripherals. The pull-up resistor controls rise time and current, while the comparator input determines which level is translated. Signal direction, inversion, propagation delay, bus capacitance, and the sink-current limit of the receiving logic must all be considered before treating the interface as transparent.
پێشنیارکراو
Window Comparator and Signal Crossing Detection
The LM339DT supports window detection and signal-crossing functions when two comparator channels compare a signal against upper and lower thresholds. One output indicates that the input is above the window, while the other indicates that it is below the window; their open-collector outputs can then drive a combined state. This arrangement is useful for amplitude protection, channel selection, and simple event detection. Threshold accuracy depends on the exact LM339DT offset specification, reference quality, and resistor tolerances. Add input filtering where noise could cause repeated transitions, and verify the hysteresis scheme so the state does not chatter around either threshold.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM339DT — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM239DR | LM2901DR | LM339DR | LM339DT | LM339DR2G |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | Texas Instruments | Texas Instruments | Texas Instruments | ROHM Semiconductor | onsemi |
| Package | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 |
| Comparator Configuration | Four independent channels | Four independent channels | Four independent channels | Four independent channels | Four independent channels | Four independent channels |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Functional Match | Quad precision-voltage comparator | Quad comparator in the same 14-pin SOIC footprint | Quad comparator with an extended automotive temperature option | Highly compatible quad comparator with similar electrical characteristics | Same ordering code and quad comparator function from a different manufacturer | Identical primary performance profile reported in the comparison listing |
جیاکەرەوە سەرەکییەکان
- Combines four independent comparator channels with open-collector outputs in one SOIC-14 package (بەراورد بەLM339DR)
- Wide supply operating range (بەراورد بەLM2901DR)
- Directly identified same-package cross-brand option (بەراورد بەLM339DT)
تێبینییەکانی دیزاین
Place each comparator's input components and output pull-up resistor close to the corresponding SOIC-14 pin. Keep the analog input traces short, away from switching-node copper, and use a continuous ground plane to minimize common-impedance noise. Because pins 4 and 11 provide ground, both should be connected with low-impedance vias rather than treating either pin as optional.
Do not omit the pull-up resistor on an open-collector output. Select the resistor to provide a valid high level while remaining below the output sink-current limit, then calculate the RC rise time against the receiving logic and bus capacitance. Also verify input common-mode and differential limits; the 2 V to 36 V supply rating does not mean every input can safely tolerate the full supply range.
Use the two ground pins as the primary return path for the comparators, but keep relay, solenoid, and switching-power-node return currents out of the sensitive input reference area. Where several outputs are connected to a wired-OR bus, isolate that bus from high-capacitance nodes and verify that only one channel can sink current at a time. A small input filter can suppress noise, but added capacitance may slow response and increase power transients.
زانیاری پابەندبوون
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for the exact LM339DT ordering code. The LM2901DR cross-reference listing mentions an extended automotive temperature range, but it does not by itself establish AEC-Q100 qualification.