LM358P - Dual 700kHz Operational Amplifier | Texas Instruments
MPN: LM358P ✓ چالاکLM358P گشتی
An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose open-loop gain is intended to be shaped by external feedback. The LM358P contains two separate amplifier channels in one 8-pin package, reducing board area compared with two discrete single-channel devices. Internally frequency-compensated channels simplify closed-loop design by reducing the additional compensation work normally required for stable operation.
Key features include two independent amplifier circuits, high gain, internal frequency compensation, single-supply operation, and a wide 3 V to 32 V supply range. The 700 kHz bandwidth supports general-purpose signal conditioning rather than high-speed precision work, while the 0.3 V/µs slew rate limits how quickly a large output transition can occur. These characteristics make the device suitable for conventional industrial and consumer analog signal paths operating from a single supply.
The LM358P is offered in a through-hole PDIP package, which supports manual assembly, prototyping, educational designs, and repair work. The dual-channel configuration allows a board to implement two amplifier functions without using two separate packages. Because the verified data identifies the device as a standard general-purpose amplifier rather than a rail-to-rail precision op amp, applications requiring rail-to-rail input or output operation, low offset, or low noise should verify those requirements against the manufacturer datasheet before final design approval.
Typical uses include single-supply buffer stages, sensor-signal conditioning, feedback amplifiers, integrators, comparators, and general analog control blocks. Two channels can also implement related functions such as an instrumentation-style buffer or a transimpedance amplifier, provided the designer accounts for the LM358P's input common-mode range, output swing, output-current capability, stability requirements, and noise characteristics.
A key design consideration is power bypassing. Place the supply-decoupling capacitor close to the positive supply and ground pins, and keep feedback components and signal routing compact to minimize oscillation and pickup. Component selection should preserve useful loop gain and phase margin rather than relying only on nominal bandwidth. For applications with unusually high precision, very low noise, or demands for rail-to-rail operation, verify the complete electrical limits before committing to this device.
This page consolidates the verified distributor and manufacturer information for LM358P, adds a pin-level package reference, compares documented drop-in candidates, and organizes practical sourcing and design guidance for engineers evaluating the Texas Instruments LM358P.
جێگرەوەکانی جێگۆڕکێ بۆ LM358P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM358P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Maximum Supply Voltage, Frequency Compensation, Number of Amplifiers, Operating Temperature Range.
LM2904P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM258P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →RC4558P
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MC1458P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →HA17904PS
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM358P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | Dual operational amplifier |
| Amplifier Circuit Count | 2 circuits |
| Channel Architecture | 2 independent operational amplifiers |
| Supply Voltage Range | 3 V to 32 V |
| Supply Type | Single supply |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| Frequency Compensation | Internally frequency compensated |
| Voltage Gain | High gain |
| پاکێج | 8-pin PDIP |
| ژمارەی پین | 8 pins |
| جۆری دامەزراندن | Through-hole |
| Product Classification | Standard general-purpose amplifier |
ڕێکخستنی پینی LM358P
| پین 1 | OUT1 — Output of amplifier 1 |
| پین 2 | IN1- — Inverting input of amplifier 1 |
| پین 3 | IN1+ — Non-inverting input of amplifier 1 |
| پین 4 | V- — Ground or negative supply connection |
| پین 5 | IN2+ — Non-inverting input of amplifier 2 |
| پین 6 | IN2- — Inverting input of amplifier 2 |
| پین 7 | OUT2 — Output of amplifier 2 |
| پین 8 | V+ — Positive supply connection |
بەکارهێنانە باوەکان
LM358P گونجاوە بۆ 6 بەکارھێنانs: Single-Supply Sensor Signal Conditioning, General-Purpose Voltage Buffer, Transimpedance Amplifier, Active Low-Pass Filter, Comparator and Threshold Circuit, Educational and Prototyping Circuits.
Single-Supply Sensor Signal Conditioning
The LM358P fits conventional sensor-conditioning blocks because its two independent channels can amplify or buffer signals while operating from a 3 V to 32 V single supply. A typical implementation uses one channel as a non-inverting amplifier and the second for filtering or an active gain stage. The verified 700 kHz gain-bandwidth product supports general-purpose signals, while the 0.3 V/µs slew rate must be checked against the required output transition rate. Because the common-mode range and output swing are not present in the supplied data, the input and output operating points must be validated against the manufacturer datasheet before deployment.
پێشنیارکراو
General-Purpose Voltage Buffer
The LM358P can implement two unity-gain voltage buffers for impedance isolation, signal distribution, or level conditioning. With a verified gain-bandwidth product of 700 kHz and internal frequency compensation, it is appropriate for conventional low-to-moderate-frequency control and instrumentation signals rather than wideband data acquisition. Feedback should connect directly from output to the inverting input for voltage following. Verify the source impedance, load impedance, output-current limit, and required output swing because those detailed limits are not included in the verified excerpt.
پێشنیارکراو
Transimpedance Amplifier
The LM358P can serve in a basic transimpedance stage where a photodiode or other current-source sensor feeds the inverting input and a feedback resistor converts current to voltage. The two available channels can be used for a second gain or filter stage. Its 700 kHz bandwidth and 0.3 V/µs slew rate provide a defined starting point for loop analysis, but photodiode capacitance, feedback resistance, and input-bias-current error can materially affect the design. Confirm those parameters and the input common-mode limits in the manufacturer datasheet before selecting the feedback network.
پێشنیارکراو
Active Low-Pass Filter
The LM358P can implement an active low-pass filter for removing high-frequency noise from a sensor or control signal. Its two channels allow a cascaded second-order filter or an inverting stage followed by a filter, while the verified 3 V to 32 V supply range supports single-rail systems. The 700 kHz gain-bandwidth product should provide ample closed-loop bandwidth for many low-frequency filters, although the 0.3 V/µs slew rate must be compared with the expected signal amplitude and frequency. Confirm output swing and stability at the selected gain and load before finalizing component values.
پێشنیارکراو
Comparator and Threshold Circuit
The LM358P can implement a comparator-style threshold circuit when one channel is used as an open-loop comparator and the other provides additional signal handling. The device is rated for 3 V to 32 V single-supply operation and includes internal frequency compensation, making it practical for conventional control thresholds. However, the verified data does not include input common-mode range, output-level behavior, response time, or output-current specifications. Those values must be checked against the manufacturer datasheet, especially if the reference voltage is close to either supply rail.
پێشنیارکراو
Educational and Prototyping Circuits
The LM358P is well suited to breadboard prototypes, laboratory exercises, and repair boards because it combines two amplifier channels in a through-hole 8-pin PDIP package. The verified 700 kHz bandwidth and 0.3 V/µs slew rate make it practical for demonstrating non-inverting, inverting, buffer, comparator, and basic filter configurations. The single-supply range of 3 V to 32 V simplifies supply planning for many classroom supplies. Because the package exposes a broad supply range, students should still verify common-mode range, output swing, and input offset before drawing conclusions about precision performance.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM358P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM2904P | LM258P | RC4558P | MC1458P | HA17904PS |
|---|---|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP - same | 8-pin PDIP - same | 8-pin PDIP - same | 8-pin PDIP - same | 8-pin PDIP - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics | onsemi | Renesas Electronics |
| Amplifier Channels | 2 independent channels | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier | Dual operational amplifier |
جیاکەرەوە سەرەکییەکان
- Factory-specified operating characteristics (بەراورد بەLM2904P)
- Dual channels in one through-hole package (بەراورد بەLM324D)
- Industry-standard PDIP replacement route (بەراورد بەMC1458P)
تێبینییەکانی دیزاین
Place the supply-bypass capacitor immediately adjacent to pin 8 and the ground return to pin 4, with the shortest practical connection to the power distribution network. Keep the two amplifier channels electrically separate where practical, and route input and output nets away from the supply-capacitor return. Although the LM358P uses internal frequency compensation, poor supply bypassing can still introduce instability, noise, or unexpected behavior in high-gain feedback networks.
Do not treat a single-supply rating as permission for signals to reach either rail. The verified data confirms a 3 V to 32 V supply range but does not provide the input common-mode range or output swing. Before selecting bias points, compare the sensor output, reference voltage, and required output voltage with those limits in the manufacturer datasheet. Also verify that the application does not require rail-to-rail input or output behavior, low offset, or low noise beyond this general-purpose device’s capability.
For feedback resistors and capacitors, begin from the required closed-loop bandwidth and phase margin rather than using the 700 kHz gain-bandwidth product as an unconditional stability limit. Keep feedback-loop area small and connect the feedback divider close to the inverting input. When driving capacitive loads or long cables, add an isolation resistor and evaluate the resulting stability with the manufacturer’s guidance; the 0.3 V/µs slew rate alone does not guarantee acceptable behavior in every load condition.
زانیاری پابەندبوون
The supplied verified data does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These fields remain unknown rather than being inferred from the manufacturer or package type.