Texas Instruments

LM393 - Dual Open-Collector Comparator | Texas Instruments

MPN: LM393 ✓ چالاک
2 V to 30 V Vdss SOIC-8 (D suffix) Package
MOQ: 1 |

LM393 گشتی

The Texas Instruments LM393 is a dual independent precision voltage comparator designed for single or split-supply operation, with a 2 V to 30 V supply range, common-mode input operation extending to ground, and open-collector outputs in an 8-pin SOIC surface-mount package. The two comparators operate independently and require no external output pull-up when their outputs are used as open-drain signals.

A voltage comparator is an analog semiconductor that compares two input voltages and produces a digital output indicating their relative relationship. The LM393 belongs to the comparator hierarchy within analog ICs and broader signal-conditioning and power-management systems. Unlike an operational amplifier, its output is intended to switch actively and can operate from a single supply while accepting an input common-mode range down to ground.

Key features include two independent comparator channels, differential input voltage capability up to ±38 V, and compatibility with TTL, MOS, and CMOS logic. The open-collector output allows a designer to set the output logic voltage through an external pull-up resistor. This architecture is useful when driving multiple wired-open outputs, connecting to a bus, or interfacing with a supply domain different from the comparator output pull-up.

The LM393 can operate from a single supply or split supply, while the common-mode input range reaches ground for many sensing conditions. Its differential input limit equals the maximum-rated supply voltage, but the absolute maximum rating should not be interpreted as a normal operating range. Input protection, supply sequencing, and output pull-up selection remain important design constraints.

Typical uses include window detection in power supplies, battery monitoring, sensor threshold conditioning, industrial control interfaces, automotive electronics, and consumer equipment. In each case, the LM393 provides a simple high-or-low decision without the output stage normally associated with a push-pull logic device.

For reliable designs, select the correct package ordering code, verify the temperature grade, place decoupling close to the supply pins, and use a pull-up resistor sized for the intended logic family and output-current limit. Check input transients against the absolute maximum ratings rather than relying on nominal common-mode limits.

This page combines the LM393 device description with functional guidance, drop-in replacement considerations, application patterns, and engineering-oriented comparisons. It helps buyers distinguish the open-collector dual comparator from op-amp alternatives while supporting package, temperature, and lifecycle decisions before requesting a quote.

جێگرەوەکانی جێگۆڕکێ بۆ LM393 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM393 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Operating Temperature Range, Output Type, Comparator Type, Response Time.

Texas Instruments
Package: 8-pin SOIC
Operating Temperature Range: -40 °C to +125 °C
Output Type: Open-collector
بەراوردکردن لەگەڵ LM393 →
STMicroelectronics
Package: 8-pin MiniSO (ST suffix)
Output Type: Open collector
Comparator Type: General purpose, open-collector output
بەراوردکردن لەگەڵ LM393 →
Texas Instruments
Package: 8-SOIC
Output Type: Open-collector, open-drain
بەراوردکردن لەگەڵ LM393 →
Texas Instruments
Package: 8-pin small-outline package (SOP-8)
Output Type: Open-collector
Comparator Type: Dual differential voltage comparator
بەراوردکردن لەگەڵ LM393 →
Texas Instruments
Package: 8-pin SOIC (D)
Operating Temperature Range: -40°C to +85°C
Output Type: Open-collector
بەراوردکردن لەگەڵ LM393 →
STMicroelectronics
Package: SOIC-8
Operating Temperature Range: -40°C to +105°C
Output Type: Open Collector
بەراوردکردن لەگەڵ LM393 →
Texas Instruments
Package: 8-pin SOIC (D), 3.90 mm width
Operating Temperature Range: 0 °C to 70 °C
Output Type: Open-collector
STMicroelectronics
Package: 8-pin SOIC-8 (SO-8), surface mount
Operating Temperature Range: -40 C to +125 C
Output Type: Push-pull CMOS
بەراوردکردن لەگەڵ LM393 →
STMicroelectronics
Package: 8-pin SOIC
Operating Temperature Range: -40 °C to 125 °C
Output Type: CMOS open-drain
بەراوردکردن لەگەڵ LM393 →

LM293DR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
Dual differential comparator · Two independent comparators · Open-collector, open-drain · Rail-to-rail · Single supply or split supply

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM2903DR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
Dual differential comparator · 2 channels · 2 V to 36 V · Open-collector · 300 ns · 8-pin SOIC · Surface mount · -40 °C to +125 °C

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM393BIDR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
Dual differential general-purpose comparator · 2 channels · Open-collector · 38 V · -38 V to +38 V · Includes ground · 2.5 mV

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM393DT

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 SOIC-8
2 · 2 V to 36 V · ±1 V to ±18 V · 0.4 mA (typical) · 2 mV (typical) · 25 nA (typical) · 1.3 µs (typical) · Open Collector

✓ بەردەستە

$0.0461 / یەکە

بینینی داتاشیت →

LM393

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 SOIC-8
2 (dual independent) · 2 V to 30 V · ±1 V to ±15 V · 2.0 mV (typical) · ±38 V · Includes ground (V-) · Open-collector, rail-to-rail input capable · TTL, MOS, CMOS (with external pull-up)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

TS393CD

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 SOIC-8
Dual general-purpose voltage comparator · 2 channels · 9 µA typical per comparator · 2.7 V to 16 V · 10^12 ohms typical · 2.5 µs typical · 6.5 mV maximum · 0.0006 µA

پەیوەندی بۆ نرخ

بینینی داتاشیت →

LM393 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Comparator Channels 2 (dual independent)
Supply Voltage Range (single) 2 V to 30 V
Supply Voltage Range (split) ±1 V to ±15 V
Input Offset Voltage 2.0 mV (typical)
Maximum Differential Input Voltage ±38 V
Common-Mode Input Range Includes ground (V-)
جۆری دەرچوون Open-collector, rail-to-rail input capable
Logic Compatibility TTL, MOS, CMOS (with external pull-up)
مەودای پلەی گەرمیی کارکردن 0°C to +70°C (LM393 commercial grade)
پاکێج SOIC-8 (D suffix)
جۆری دامەزراندن Surface Mount
ژمارەی پینەکان 8
Extended Temperature Variant LM293 (-25°C to +85°C), LM2903 (-40°C to +125°C)

ڕێکخستنی پینی LM393

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 OUT A — Comparator A open-collector output
پین 2 IN A- — Comparator A inverting input
پین 3 IN A+ — Comparator A non-inverting input
پین 4 V- / GND — Negative supply / ground (single supply)
پین 5 IN B+ — Comparator B non-inverting input
پین 6 IN B- — Comparator B inverting input
پین 7 OUT B — Comparator B open-collector output
پین 8 V+ — Positive supply (2 V to 30 V)

بەکارهێنانە باوەکان

LM393 گونجاوە بۆ 6 بەکارھێنانs: Power Supply Window Detection, Battery Low-Voltage Monitoring, Sensor Threshold Conditioning, Industrial Control Interfaces, Automotive Electronics, Consumer Electronics Timing and Level Detection.

⚡

Power Supply Window Detection

The LM393's dual comparator channels make it a natural fit for power-supply window detection, where an undervoltage and an overvoltage threshold must both be monitored on the same rail. One channel compares a divided-down rail voltage against the upper trip point while the second channel compares it against the lower trip point; because both outputs are open-collector, they can be wire-ORed into a single power-good flag without additional logic gates. The 2 V to 30 V supply range lets the LM393 monitor rails directly at industrial levels, and the common-mode range extending to ground permits detection of fully collapsed supplies. With a 2.0 mV typical offset, thresholds as tight as a few tens of millivolts are practical, and the open-collector outputs interface cleanly with the supervisor or microcontroller logic domain via a pull-up resistor.

🔋

Battery Low-Voltage Monitoring

Battery protection circuits need a comparator that keeps working as the cell discharges toward its cutoff, and the LM393's 2 V minimum supply and ground-including common-mode range match this requirement directly. A resistor divider scales the cell voltage into one input while a reference - a Zener, bandgap shunt such as the TL431, or the cell voltage itself - feeds the other; the open-collector output then asserts a low-side warning or triggers load disconnect through a MOSFET driver. Because the output high level is defined by the pull-up rail rather than the comparator supply, the same circuit can flag faults to a 3.3 V microcontroller even while the comparator supervises a higher-voltage pack. The low quiescent draw of the LM393 family is an additional benefit for always-on battery monitors, and the LM2903 grade covers outdoor temperature extremes.

🧩

Sensor Threshold Conditioning

Discrete sensor signals - photoresistor bridges, NTC thermistor dividers, hall latches, and comparator-based module front ends such as the common LM393 sensor boards - rely on a simple high-or-low decision element. The LM393's common-mode input range extending to ground accepts near-zero sensor outputs from single-supply boards, while its ±38 V differential tolerance provides robustness against inductive sensor spikes and wiring faults that would damage higher-precision comparators. Each of the two channels can condition an independent sensor, and the open-collector outputs allow a shared pull-up when two sensors must vote on a single enable line. Adding positive feedback from output to the non-inverting input converts the LM393 into a Schmitt trigger, eliminating chatter on slowly moving analog signals such as temperature ramps or light-level transitions.

🏭

Industrial Control Interfaces

Industrial environments impose wide supplies, noisy grounds, and demanding temperature ranges, and the LM393 family addresses these with a 30 V maximum supply, ±38 V differential input tolerance, and the LM2903 sibling grade rated -40°C to +125°C in the same pinout. Typical roles include limit-switch comparison, over-current flag generation across a shunt resistor, level detection on 24 V control signals, and thermostat-style hysteresis loops. The open-collector output is particularly valuable here: it can be pulled up to a 5 V PLC input rail while the comparator itself monitors a 24 V bus, providing galvanic-domain translation in a single 8-pin device. Wire-OR combining of multiple fault outputs into one alarm line reduces wiring and logic complexity, and the industry-standard pinout keeps second sources available for long service lifetimes.

🚗

Automotive Electronics

Automotive subsystems - load-dump monitoring, lamp-failure detection, coolant-temperature warnings, and seat-position sensing - require comparators rated for harsh temperature and transient conditions. While the commercial LM393 itself is specified 0°C to +70°C, the pin-identical LM2903 family extends coverage to -40°C to +125°C, allowing one PCB layout to serve both consumer and vehicular builds by swapping the comparator suffix alone. The 30 V supply rating absorbs nominal 12 V battery systems with headroom, and the ±38 V differential limit provides margin against inductive load-dump events on switched battery lines. Open-collector outputs drive indicator lamps through transistors or report faults to body-controller logic through a pull-up on the clean 5 V rail, and dual channels let one device supervise two independent thresholds per module.

📺

Consumer Electronics Timing and Level Detection

Cost-sensitive consumer products use the LM393 for chargers, remote-control receivers, smoke-alarm sensor interfaces, appliance water-level detection, and RC timing-vs-threshold comparison. Its commodity pricing, availability from TI, ST, onsemi, and domestic brands, and near-universal SOIC-8 footprint simplify sourcing and second-sourcing for high-volume builds. The device tolerates relaxed layout and inexpensive decoupling, and its two channels often replace an entire discrete transistor comparator stage, reducing BOM count. Where a design later needs tighter thresholds, the LM393B drops into the same footprint with improved offset specifications - a common upgrade path during product cost-down or quality-improvement revisions without any PCB respin, since pin functions and package remain identical across the whole 393 family.

What is the supply voltage range of the LM393?
The LM393 operates from a single supply of 2 V to 30 V or from split supplies of ±1 V to ±15 V. According to the onsemi LM393 datasheet, the wide supply range with common-mode input extending down to ground makes single-supply threshold sensing possible without a negative rail, which is one reason the part remains a general-purpose design staple.
Where can I download the LM393 datasheet PDF?
You can download the LM393 datasheet PDF from the manufacturer product pages: Texas Instruments hosts it at ti.com/product/LM393, and onsemi publishes it at onsemi.com/download/data-sheet/pdf/lm393-d.pdf. Both documents cover the dual comparator family including LM193, LM293, LM393, and LM2903 grades, with pinout, electrical characteristics, and application circuits. A datasheet link is also provided on this page above the specifications table.
What is the pinout of the LM393 in SOIC-8?
In the 8-pin SOIC package, the LM393 pinout is: pin 1 = OUT A, pin 2 = IN A- (inverting), pin 3 = IN A+ (non-inverting), pin 4 = V- / GND, pin 5 = IN B+ (non-inverting), pin 6 = IN B- (inverting), pin 7 = OUT B, and pin 8 = V+. The pin diagram on this page shows the standard SOIC-8 layout with pin 1 at the top-left dot marker.
What is the difference between LM393 and LM2903?
The main difference is the operating temperature range. The LM393 is commercial grade, specified from 0°C to +70°C, while the LM2903 is specified from -40°C to +125°C for industrial and automotive environments. Both devices are pin-to-pin compatible in the same SOIC-8 package with open-collector dual outputs, so the LM2903 can serve as a direct LM393 replacement when extended temperature coverage is required.
What is the difference between LM393 and LM393B?
The LM393B is TI's improved B-version of the classic LM393. It keeps the same pinout, package, and open-collector dual-comparator architecture but offers tightened specifications, including a lower maximum input offset voltage, so it functions as a drop-in upgrade. TI groups LM393B, LM2903B, LM193, LM293, LM393, and LM2903 in one datasheet (Rev. AH) because they share the same footprint and differ mainly in performance and temperature grade.
What is the best drop-in replacement for the LM393?
The best drop-in replacements are LM293 (wider -25°C to +85°C range), LM2903 (-40°C to +125°C), and the improved LM393B, all from TI and pin-to-pin compatible in SOIC-8. Cross-brand, STMicroelectronics LM393DT and onsemi LM393 are pin-for-pin equivalents, and ST TS393 is also listed as a verified cross. Confirm temperature grade and offset specifications against your circuit before substituting.
What is the best alternative brand equivalent for LM393?
For a cross-brand equivalent, STMicroelectronics LM393DT is the most common choice: it is a pin-for-pin dual open-collector comparator in the same 8-pin SOIC package with matching supply range and commercial temperature grade. onsemi also manufactures the LM393 series, and Sourceics lists TS393 as a verified pin-compatible cross. Because the LM393 pinout is an industry-standard footprint, nearly every comparator vendor offers a compatible dual part.
Can the LM393 be used with a 5V single supply?
Yes. The LM393 operates from 2 V to 30 V single supply, so a 5 V rail is well within range, and its common-mode input range includes ground, allowing near-zero threshold detection without a negative supply. The open-collector output needs an external pull-up resistor, typically 1 kΩ to 10 kΩ, to the logic rail you want the output to reference, enabling direct TTL or CMOS interfacing.
Why does the LM393 output need a pull-up resistor?
The LM393 has an open-collector output stage that can only actively pull the output low; it cannot drive the output high. An external pull-up resistor to the desired logic supply is mandatory for the output to reach a valid high level. This topology is a feature: it lets you wire-OR multiple comparator outputs, translate between voltage domains, and choose the output logic level independently of the comparator supply voltage.
Is the LM393 suitable for battery monitoring?
Yes. The LM393 is well suited to battery low-voltage detection and over-discharge protection: its 2 V minimum supply works with single-cell chemistries, the ground-including common-mode range accepts deeply discharged cell voltages, and its low power draw preserves battery life. Typical designs use a resistor divider from the battery and a reference (such as a Zener or TL431) into the comparator inputs, with the open-collector output driving an indicator or shutdown logic.
When should I choose the LM393 over a comparator like TLV1702?
Choose the LM393 when you need maximum supply voltage headroom (up to 30 V), industry-standard availability across many second sources, and lowest cost for general-purpose threshold detection. Choose a modern part such as TI TLV1702 or LM393LV when you need lower quiescent current, lower offset voltage, faster response, or operation below 2 V - TI explicitly positions LM393LV as a lower-voltage alternative with improved performance. The LM393 wins on robustness and supply-chain universality, not on speed or precision.
Is the LM393 in stock and where can I buy it?
The LM393 family is broadly available; distributor listings from DigiKey and LCSC show in-stock status for TI, ST, and domestic-brand versions of the part. For current stock, lead time, and pricing on this page, use the Request a Quote form - XAIPART will confirm availability, packing option (reel or tube), and delivery time for your required quantity, including volume pricing for production orders.
What is the price of the LM393?
The LM393 is a high-volume commodity IC, so unit pricing depends strongly on brand, grade, package suffix, and quantity. LCSC listings for domestic versions start around a few cents per unit, while branded TI SOIC-8 versions in reel packaging cost more. Because commodity prices change daily, request a current quotation using the Request a Quote form on this page for exact pricing at your quantity and delivery schedule.
What is the lead time for LM393 orders?
Because the LM393 is produced by multiple manufacturers (TI, ST, onsemi, and domestic brands) and stocked by most distributors, lead times are typically short when stock is on hand. Production-volume reels may require factory ordering with several weeks of lead time depending on the chosen brand and grade. Submit the Request a Quote form on this page to receive a confirmed lead time for your specific part number suffix, quantity, and packaging option.
What are the key specifications of the LM393 that engineers should know?
The LM393 is a dual open-collector voltage comparator: 2 V to 30 V single-supply (or ±15 V split) operation, 2.0 mV typical input offset voltage, ±38 V maximum differential input, common-mode range extending to ground, and TTL/CMOS-compatible outputs via external pull-up. It is commercial grade, 0°C to +70°C, in an 8-pin SOIC, and the outputs are wire-OR capable. Its sibling grades LM293 and LM2903 extend the temperature range to -25°C/+85°C and -40°C/+125°C respectively.

داتای سەرچاوەی ئەندازیاری بۆ LM393 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the LM393 when you need a robust, low-cost dual comparator for general-purpose threshold detection at commercial temperatures (0°C to +70°C) with wide 2 V to 30 V supply and ground-referenced inputs. Choose LM293DR if your product must survive -25°C to +85°C industrial enclosures, and LM2903DR for automotive or outdoor designs needing -40°C to +125°C - both are pin-identical, so one layout covers all grades. Choose LM393BIDR when threshold accuracy matters more than unit cost, since its offset specification is tightened but the footprint is unchanged. For second sourcing, STMicroelectronics LM393DT and onsemi LM393 are pin-for-pin equivalents of the TI part. Skip this family and consider TI TLV1702 or LM393LV when the design needs sub-2 V operation, lower quiescent current, faster response, or lower offset; TI explicitly positions LM393LV as the lower-voltage, better-performance alternative. Honest trade-off: the LM393 wins on availability, ruggedness, and second sources - not on precision or speed.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە LM293DR LM2903DR LM393BIDR LM393DT TS393
Package SOIC-8 SOIC-8 - same SOIC-8 - same SOIC-8 - same SOIC-8 - same SOIC-8 - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments STMicroelectronics STMicroelectronics
Operating Temperature Range 0°C to +70°C -25°C to +85°C -40°C to +125°C -40°C to +125°C -40°C to +125°C -40°C to +125°C
Output Type Open-collector (dual) Open-collector (dual) Open-collector (dual) Open-collector (dual) Open-collector (dual) Open-collector (dual)
Automotive Grade No (commercial grade) No Yes (Q variants available) No No No
Drop-in Footprint Compatibility Industry-standard 393 SOIC-8 pinout Pin-to-pin identical Pin-to-pin identical Pin-to-pin identical Pin-to-pin identical Pin-to-pin identical

جیاکەرەوە سەرەکییەکان

  • Widest temperature-grade selection in one pinout (بەراورد بەLM2903DR)
  • Higher supply voltage headroom than modern low-voltage alternatives (بەراورد بەTS393)
  • Drop-in precision upgrade path (بەراورد بەLM393BIDR)

تێبینییەکانی دیزاین

Always fit an external pull-up resistor on each LM393 output - the open-collector stage cannot drive high on its own. Size the pull-up for the load: 1 kΩ to 5 kΩ gives fast edges into logic inputs, while 10 kΩ to 100 kΩ suits battery-powered flag circuits where sinking current must be minimized. The pull-up rail can differ from V+ (for example, pull up to 3.3 V while the comparator runs on 24 V), but keep the output-to-V- voltage within the datasheet absolute maximum and respect the maximum output sink current when sizing the resistor low value.

The LM393 is an uncompensated comparator and will oscillate when driven with slow-moving input signals, especially when inputs sit near the trip point with high source impedance. Add positive feedback (a hysteresis resistor from output back to the non-inverting input) to create a Schmitt trigger with a few tens of millivolts of dead band - a 100 kΩ feedback resistor against a 10 kΩ divider gives roughly 10x the offset voltage of hysteresis. Keep input traces short and route them away from switching nodes; the ground-including common-mode range makes ground-bounce on the sensing node a real trip-point error source.

Do not treat the ±38 V differential input rating as a normal operating range - it is an absolute maximum, and repeated excursions degrade input pairs. On split-supply designs such as the ±12 V application discussed in the TI E2E forum, remember the commercial LM393 is specified only 0°C to +70°C; select LM293 or LM2903 for extended temperature. Unused comparator channels should have both inputs tied to a defined rail (not left floating) to prevent erratic output chatter, and the corresponding output can simply be left unterminated or pulled up if the flag is needed.

Place a 100 nF ceramic decoupling capacitor directly across the V+ (pin 8) and V- (pin 4) pins; on 24 V industrial boards, add a bulk 1 uF to 10 uF capacitor for load transients. Because the outputs sink current to V-, their return paths flow through the ground pin - give the output pull-up returns a low-impedance path to pin 4 so switched sink currents do not modulate the sensitive input ground. The 393 SOIC-8 footprint is industry standard, so reserve through-hole pads on prototype boards for easy swapping between TI, ST, and onsecond-source parts.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance status was not stated in the retrieved product listings. Request RoHS/REACH certificates via the Request a Quote form. For automotive qualification, use the LM2903 Q-grade variants.

داتا پشتڕاستکراوەتەوە لە: 2026-11-08 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

lm393 datasheet lm393 pinout lm393 comparator lm393 spice model lm393 circuit example lm393 sensor module lm393 equivalent lm393 replacement lm393 vs lm2903 lm393 vs lm358 lm393 price Texas Instruments lm393

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments LM393 LM293 LM2903 LM393B TS393 STMicroelectronics onsemi voltage comparator analog comparator dual differential comparator open-collector output SOIC-8 surface mount single-supply operation input offset voltage common-mode input range TTL compatibility RoHS battery monitoring window detection sensor threshold conditioning Schmitt trigger hysteresis TL431 voltage reference
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ