MAX3483AEASA+T - 3.3V 20Mbps RS-485/RS-422 Transceiver | Analog Devices
MPN: MAX3483AEASA+T ✓ چالاکMAX3483AEASA+T گشتی
An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level signals into balanced differential signals and converts received differential signals back into CMOS-compatible data. The MAX3483 family belongs to the broader transceiver hierarchy: RS-485 and RS-422 interface transceiver, interface IC, data converter, and semiconductor. These differential interfaces improve noise immunity over single-ended communication and support longer cable runs in electrically noisy environments.
The device operates from a 3.3V supply, supports data rates up to 20Mbps, and provides ±20kV ESD protection. Slew-rate-limited driver operation reduces edge-rate harmonics and ringing on the bus, making the interface suitable for EMI-sensitive equipment. The integrated half-duplex transceiver combines a differential driver and differential receiver, while separate driver-enable and receiver-enable controls provide flexible bus-direction management.
MAX3483AEASA+T is one driver plus one receiver in an 8-pin industry-standard SO package. The receiver is designed for differential RS-422 or RS-485 buses, and the driver produces balanced differential outputs. This arrangement suits systems in which the host processor handles timing, direction control, bus arbitration, fault detection, and higher-level protocols independently of the physical interface.
Typical applications include industrial-control networks, telecommunications equipment, building automation, instrumentation, data acquisition, and EMI-sensitive transceiver modules. A single MAX3483AEASA+T is also useful for point-to-point links where the system requires a compact, low-voltage RS-485 endpoint. Multidrop designs can add multiple transceivers, but the system designer must manage termination, biasing, grounding, and node-enable sequencing.
Place the transceiver close to the connector and route the balanced bus pair as a coupled pair on the PCB. Keep the ground reference and differential traces away from switching nodes and high-current paths. Verify signal polarity, termination, common-mode range, bus loading, and protocol-specific idle states before releasing a production design.
This page combines the manufacturer's key electrical and application facts with package-aware comparisons, drop-in family options, practical PCB guidance, and direct answers for engineers evaluating the MAX3483AEASA+T.
جێگرەوەکانی جێگۆڕکێ بۆ MAX3483AEASA+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3483AEASA+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە ESD Protection, Supported Standards, Product Type, Supply Voltage, Communication Mode.
MAX3485AEASA+T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX3488AEASA+T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX3490AEASA+T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3486AEASA+T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3483EASA+T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3483AEASA+T تایبەتمەندییەکان
| ڤۆڵتیەی دابینکردن | 3.3 V |
| Maximum Data Rate | 20 Mbps |
| ESD Protection | ±20 kV |
| Supported Standards | RS-485 and RS-422 |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Driver Output Type | Differential, slew-rate limited |
| Receiver Input Type | Differential |
| پاکێج | 8-pin SOIC |
| جۆری دامەزراندن | Surface mount |
ڕێنمایی ڕێکخستنی پینی MAX3483AEASA+T 8-pin soic
ڕێکخستنی پین بۆ MAX3483AEASA+T (پاکێجی 8-pin soic). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3483AEASA+T.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MAX3483AEASA+T گونجاوە بۆ 6 بەکارھێنانs: Industrial Control Networks, Building Automation Equipment, Telecommunications Equipment, Data Acquisition Instruments, EMI-Sensitive Communication Modules, Point-to-Point Embedded Links.
Industrial Control Networks
The MAX3483AEASA+T fits industrial-control networks that require a 3.3V RS-485 or RS-422 physical interface. Its 20Mbps maximum data rate supports high-speed controller-to-module links, while ±20kV ESD protection adds useful ruggedness at connector-adjacent interfaces. The slew-rate-limited driver limits edge-rate harmonics that can couple into nearby control circuitry. Install the transceiver near the external connector, use a balanced differential pair, provide the termination required by the selected topology, and keep the ground reference adjacent to the bus pair. Firmware should control driver-enable and receiver-enable timing so that only one node drives the bus during normal communication.
پێشنیارکراو
Building Automation Equipment
The MAX3483AEASA+T is suitable for building-automation controllers, room modules, sensors, and HVAC interfaces using balanced RS-485 or RS-422 signaling. Operating from 3.3V helps simplify integration with modern embedded controllers, and the 20Mbps device limit provides headroom for common automation protocols. The differential interface improves rejection of common-mode noise found near motors, relays, and switched power stages. Place the transceiver near the field connector and separate its differential route from switching-node copper. Select the receiver and driver enable states carefully during boot-up so the module does not contend with other nodes, and apply the termination and fail-safe bias network specified by the system topology.
پێشنیارکراو
Telecommunications Equipment
The MAX3483AEASA+T can serve as the physical-layer endpoint in telecommunications equipment that uses 3.3V RS-422 or RS-485 links for supervisory, status, or backplane communication. Its 20Mbps capability supports short, high-rate interconnects, while the differential driver and receiver provide noise-resistant signaling over cables running through equipment cabinets. The ±20kV ESD rating is especially relevant when the transceiver is positioned near an external connector. Route the differential pair together, provide a continuous reference plane, and avoid long stubs. Confirm common-mode limits, input thresholds, and isolation strategy in the final system because connector protection requirements can exceed the transceiver's operating ratings.
پێشنیارکراو
Data Acquisition Instruments
The MAX3483AEASA+T is appropriate for distributed data-acquisition and instrumentation systems requiring a compact, low-power differential interface. The 3.3V supply suits embedded sensor hubs, while the 20Mbps data rate supports high-speed command and status traffic over RS-485 or RS-422. Its one-driver and one-receiver arrangement gives the host processor direct control over bus direction and receive state. To protect measurement accuracy, keep the transceiver and its return path away from analog inputs and high-current actuator wiring. Use matched termination at appropriate endpoints, avoid excessive stub lengths, and verify grounding so common-mode conversion does not degrade the acquisition chain.
پێشنیارکراو
EMI-Sensitive Communication Modules
The MAX3483AEASA+T fits compact communication modules where radiated and conducted emissions are important design constraints. The slew-rate-limited driver reduces the speed of differential output transitions, limiting high-frequency energy that can radiate from cable or PCB paths. Operation from 3.3V and a 20Mbps maximum rate support modern control architectures, and ±20kV ESD protection strengthens the interface at exposed connectors. Place the transceiver close to the connector, maintain a tightly coupled differential pair, provide a nearby return path, and keep the cable away from high-dV/dt nodes. Confirm the final emissions performance with the complete module because enclosure grounding, cable construction, and power-converter layout also contribute to the result.
پێشنیارکراو
Point-to-Point Embedded Links
The MAX3483AEASA+T works well for point-to-point embedded links between a controller and a peripheral when a short balanced cable is required. Its integrated driver and receiver occupy one 8-pin SOIC package, while 3.3V operation and a 20Mbps maximum rate align with modern embedded logic. The compact footprint supports dense equipment designs, and the slew-rate-limited output helps control cable and PCB emissions. Connect the differential outputs and inputs to the corresponding bus pair, provide a common reference, and install termination according to the physical-layer guidance. Since the transceiver does not determine protocol behavior, the host firmware must also manage idle states, direction, fault recovery, and any required fail-safe biasing.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MAX3483AEASA+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MAX3485AEASA+T | MAX3488AEASA+T | MAX3490AEASA+T | MAX3486AEASA+T | MAX3483EASA+T |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Maximum Data Rate | 20 Mbps | 20 Mbps | 20 Mbps | 20 Mbps | 20 Mbps | 20 Mbps |
| ESD Protection | ±20 kV | ±20 kV | ±20 kV | ±20 kV | ±20 kV | ±20 kV |
| Driver and Receiver Count | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver | 1 driver and 1 receiver |
| Supported Interfaces | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
| Temperature Grade | AE automotive extended grade | AE automotive extended grade | AE automotive extended grade | AE automotive extended grade | AE automotive extended grade | E grade |
جیاکەرەوە سەرەکییەکان
- Integrated single-driver and single-receiver RS-485/RS-422 interface (بەراورد بەMAX3488AEASA+T)
- Slew-rate-limited differential driver for EMI control (بەراورد بەMAX3490AEASA+T)
- 20Mbps operation with ±20kV ESD protection (بەراورد بەMAX3486AEASA+T)
- Exact same-family AE temperature-grade option (بەراورد بەMAX3483EASA+T)
تێبینییەکانی دیزاین
Place the MAX3483AEASA+T close to the external connector and route the two differential bus conductors as a tightly coupled pair with a continuous reference plane. Keep the pair away from switching nodes, inductors, and high-current return paths. If the board also carries non-differential interfaces, preserve adequate spacing between the differential pair and unrelated high-speed traces to minimize crosstalk and conversion of common-mode noise into differential error.
Validate termination, fail-safe bias, cable length, node loading, and topology against the operating data rate. The 20Mbps rating is the device-level maximum and does not guarantee that every physical configuration supports 20Mbps. Keep stubs short, install termination only at the locations prescribed by the physical-layer design, and test the finished cable, connectors, grounding, and transceiver placement together because reflections can depend on the complete interconnect.
Do not substitute the MAX3483AEASA+ and MAX3483AEASA+T ordering codes without checking the package form and required reel quantity. Also verify driver-enable and receiver-enable polarity before replacing a family member. A shared 8-pin SOIC outline does not guarantee identical control behavior, fail-safe biasing, or shutdown operation, so the manufacturer pin-description and electrical-characteristics tables should govern every replacement decision.
The slew-rate-limited driver helps reduce high-frequency harmonics on the differential outputs, but emissions performance still depends on the complete product. Maintain a short connection to the cable connector, use a balanced cable, provide an effective equipment ground, and keep switching converters and their high-dV/dt paths away from the transceiver. Conduct system-level EMC testing because enclosure resonances, cable construction, filtering, and power-supply layout can dominate final emissions results.
زانیاری پابەندبوون
The AE ordering designation identifies an automotive extended grade, but no explicit AEC-Q100, RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified in the cited manufacturer records.