MAX3488AEASA+T - 3.3V 20Mbps RS-485/RS-422 Transceiver
MPN: MAX3488AEASA+T ✓ چالاکMAX3488AEASA+T گشتی
An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and converts received differential signals back into CMOS-compatible logic. It belongs to the broader hierarchy of interface transceiver, communications interface, and semiconductor devices. Balanced differential signaling is widely used in industrial control, instrumentation, building automation, and data-communication systems because it improves noise immunity and permits reliable transmission over longer cables than single-ended interfaces.
The MAX3488 family combines a reduced-voltage 3.3V supply with high-speed RS-485 and RS-422 operation. Its slew-rate-limited driver limits the rate at which output transitions occur, which helps control edge-generated EMI and reduces the possibility of unwanted reflections on poorly terminated interconnects. The 20kV ESD rating strengthens its suitability for interfaces exposed to electrostatic discharge in industrial and communications equipment.
Each device integrates one driver and one receiver, allowing a compact node implementation with both transmit and receive paths. The driver converts a differential logic input into balanced driver outputs, while the receiver converts a differential input into a single-ended receiver output. Because the MAX3488 supports both RS-485 and RS-422 applications, design decisions involving bus topology, termination, grounding, and driver enable control remain central to successful deployment.
Typical uses include industrial sensor gateways, programmable logic controller communication, motor-control equipment, data acquisition units, building-automation controllers, and isolated supervisory-control equipment. The 8-pin SOIC footprint simplifies assembly in conventional surface-mount production and provides a practical transition from higher-voltage interface designs to a 3.3V system supply.
Designers should confirm the exact receiver threshold, driver enable timing, common-mode limits, and package pin assignments in the manufacturer datasheet before final routing. Termination strategy must be selected for the cable length, topology, and signal rate. Keep the differential pair routed with continuous reference, minimize stubs, and place termination components where the signal can be physically disconnected during testing.
This product page combines the exact orderable part number, family-level electrical characteristics, package information, application guidance, design notes, and clearly qualified replacement analysis to support faster component selection and PCB planning.
جێگرەوەکانی جێگۆڕکێ بۆ MAX3488AEASA+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3488AEASA+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە ESD Protection, Supply Voltage, Supported Standards, Product Type, Driver Configuration.
MAX3485EASA+T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3486EASA+T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3490EASA+T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3491EASA+T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3483EASA+T
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3490AEGSA+T
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX3488AEASA+T تایبەتمەندییەکان
| Product Type | RS-485/RS-422 transceiver |
| Manufacturer | Analog Devices / Maxim Integrated |
| ڤۆڵتیەی دابینکردن | 3.3 V |
| Maximum Data Rate | 20 Mbps |
| ESD Protection | 20 kV |
| Driver Configuration | 1 driver |
| Receiver Configuration | 1 receiver |
| Supported Standards | RS-422 and RS-485 |
| Driver Edge Rate | Slew-rate limited |
| Transceiver Power Class | Low-power |
| پاکێج | 8-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Ordering Package | Tape and reel |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
ڕێنمایی ڕێکخستنی پینی MAX3488AEASA+T tape and reel
ڕێکخستنی پین بۆ MAX3488AEASA+T (پاکێجی tape and reel). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3488AEASA+T.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MAX3488AEASA+T گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Gateway, PLC Communication Module, Building Automation Controller, Data Acquisition Unit, Motor Control Equipment, Data and Control Networking.
Industrial Sensor Gateway
The MAX3488AEASA+T fits a 3.3V industrial sensor gateway that must collect field-controller data over an RS-485 bus. Its one-driver, one-receiver arrangement provides a compact bidirectional node, while the confirmed 20Mbps maximum data rate gives substantial margin above typical low-speed field-bus traffic. The slew-rate-limited driver also helps control edge energy on cables running near motors, contactors, and switching power supplies. Place the differential route as a controlled-impedance pair, use termination appropriate to the bus topology, and confirm common-mode and temperature limits against the manufacturer datasheet.
پێشنیارکراو
PLC Communication Module
The MAX3488AEASA+T is suitable for a compact programmable-logic-controller communication interface operating from a 3.3V rail. The integrated driver and receiver allow one package to handle both transmission and reception, reducing the board area needed for a dual-transceiver arrangement. At the same time, its 20Mbps rating supports modern industrial links that may operate well above legacy RS-485 rates. Control driver enable timing carefully to avoid bus contention, and use the manufacturer pin and timing tables when defining the host UART handshake.
پێشنیارکراو
Building Automation Controller
The MAX3488AEASA+T can connect a 3.3V building-automation controller to RS-485 or RS-422 field equipment. Its low-power 3.3V operation fits embedded controllers with constrained supply capacity, and the slew-rate-limited driver reduces edge-generated coupling that could disturb nearby sensor and control circuitry. In a multi-drop installation, enable only one driver at a time and determine termination placement from the physical bus topology. Verify common-mode range, ground-reference strategy, ESD requirements, and operating temperature against the installed environment.
پێشنیارکراو
Data Acquisition Unit
The MAX3488AEASA+T is appropriate for a distributed data-acquisition unit that receives commands and returns measurement data over a differential bus. The 20Mbps capability supports high headroom when acquisition nodes exchange bursts of data, while one integrated driver and receiver keep the node circuitry compact. For reliable operation, route the pair away from switching nodes and connectors, provide a continuous ground reference, and avoid long unprotected stubs. Confirm the receiver threshold and common-mode limits in the manufacturer datasheet before defining the analog and digital grounding boundary.
پێشنیارکراو
Motor Control Equipment
The MAX3488AEASA+T can be used in motor-control equipment for command, status, and diagnostic communication between a controller and remote drive or sensor electronics. The slew-rate-limited transmitter is useful in systems where reducing transition-generated EMI is important near power-conversion circuitry. The device should remain electrically compatible with the motor system's common-mode and grounding conditions, which can vary significantly with power-stage topology. Keep interface routing separate from high-current switching paths, use a suitable bus-stiffening strategy where required, and validate conducted and radiated emissions in the completed equipment.
پێشنیارکراو
Data and Control Networking
The MAX3488AEASA+T supports a 3.3V data and control network that carries RS-485 or RS-422 traffic between distributed equipment. Its 20Mbps maximum rate provides high performance headroom, while the low-power family designation can simplify supply planning in compact nodes. RS-422 point-to-point links and RS-485 multidrop buses require different termination and enable arrangements, so the bus topology must be fixed before component substitution. Preserve differential-pair geometry, use equal-length routing where synchronization matters, and validate the complete cable network under representative noise conditions.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MAX3488AEASA+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MAX3485EASA+T | MAX3486EASA+T | MAX3490EASA+T | MAX3491EASA+T | MAX3483EASA+T | MAX3490AEGSA+T |
|---|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | RS-485/RS-422 transceiver | MAX3488-family transceiver | MAX3488-family transceiver | MAX3488-family transceiver | MAX3488-family transceiver | MAX3488-family transceiver | MAX3488-family transceiver |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Driver Count | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| Receiver Count | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
جیاکەرەوە سەرەکییەکان
- Confirmed 20Mbps family performance (بەراورد بەMAX3490AEGSA+T)
- Slew-rate-limited driver in the selected transceiver (بەراورد بەMAX3490AEGSA+T)
- Single integrated transceiver in a standard 8-pin SOIC (بەراورد بەMAX3486EASA+T)
تێبینییەکانی دیزاین
Route the driver and receiver differential signals as a tightly coupled pair with continuous ground reference. Avoid introducing vias where practical, keep the pair away from switching nodes, clock edges, and high-current return paths, and preserve symmetry between the two conductors. Stubs should be minimized because an unterminated branch can reflect a fast edge and degrade receiver performance. Connector and protection-device placement should also favor a direct differential path.
Do not enable more than one driver on the same RS-485 segment at a time. Define an unambiguous enable policy in firmware or hardware so that bus contention cannot occur during startup, reset, or mode changes. For RS-422, verify the source and destination count against the selected topology. For RS-485, determine termination from the physical bus rather than placing termination at every node, and validate the complete network with the intended cable.
The slew-rate-limited driver helps reduce edge-generated electromagnetic interference, but layout remains the primary EMI control. Keep switching supplies, relays, motor drivers, and their high-current paths physically separated from the balanced pair. Use a practical common-mode and ground-reference strategy, and verify emissions and immunity at the finished-product level. High-rate edges and long cables can still create radiated or conducted coupling despite controlled driver slew rate.
Place the transceiver's local supply-decoupling network close to its supply and ground pins, using the capacitance and placement required by the manufacturer datasheet. Keep the 3.3V interface supply return path clear of noisy power-conversion currents, and avoid sharing narrow necklaces of copper between the transceiver and high-current loads. Review the supply range, ground-reference arrangement, and startup behavior as a complete circuit rather than treating the transceiver pins independently.
زانیاری پابەندبوون
The verified product information does not state the RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The component is an industrial/communications interface IC rather than an automotive-qualified device under the available information.