Analog Devices

MAX3490AEGSA+T - 20Mbps RS-485/RS-422 Transceiver | ADI

MPN: MAX3490AEGSA+T ✓ چالاک
3.3 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
MOQ: 1 |

MAX3490AEGSA+T گشتی

The Analog Devices MAX3490AEGSA+T is a 3.3V-powered RS-485/RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 20Mbps, and ±20kV ESD protection, housed in an 8-pin SOIC package. Its slew-rate-limited driver reduces EMI and cable reflections, while true RS-485/RS-422 operation supports robust point-to-point and multidrop communications.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus voltages and converts received differential signals back into digital logic. The differential signaling provides common-mode rejection and noise immunity, making these transceivers useful for industrial control, telecommunications, instrumentation, and data links operating over longer cables than single-ended interfaces.

The MAX3490AEGSA+T combines a 3.3V supply with a 20Mbps maximum signaling rate. Its slew-rate-limited output reduces high-frequency harmonics and ringing, which can improve interoperability in systems where cable length, connectors, or imperfect termination create reflections. Integrated ±20kV ESD protection strengthens the interface against electrostatic discharge encountered during installation or handling.

Each device contains one transmitter and one receiver, allowing one half-duplex bus node to drive a differential line and receive the corresponding differential bus state. The 8-pin SOIC package supports conventional surface-mount assembly while reducing board area compared with larger transceiver packages. The +T suffix identifies the tape-and-reel ordering form for production handling.

Typical uses include industrial-control networks, building automation equipment, telecommunications interfaces, instrumentation links, and EMI-sensitive RS-422 connections. Designers should match the bus topology, cable impedance, termination method, grounding strategy, and logic-level supply requirements before finalizing the system interface.

Place the transceiver close to the connector and route the differential pair as a controlled-impedance pair. Keep the driver and receiver grounds consistent with the interface reference plane, and use the manufacturer pin description and application guidance when assigning PCB tracks. The slew-rate-limited output should be evaluated together with maximum cable length and system data rate.

This page organizes the manufacturer specifications, interface requirements, comparison points, and practical PCB guidance needed to evaluate the MAX3490AEGSA+T as a 3.3V, 20Mbps RS-485/RS-422 transceiver.

جێگرەوەکانی جێگۆڕکێ بۆ MAX3490AEGSA+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3490AEGSA+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە ESD Protection, Maximum Data Rate, Product Type, Supply Voltage, Supported Standards.

Analog Devices
ESD Protection: 20 kV
Supported Standards: RS-422 and RS-485
بەراوردکردن لەگەڵ MAX3490AEGSA+T →
Analog Devices
ESD Protection: ±15 kV
Maximum Data Rate: 12 Mbps
Supported Standards: RS-422 and RS-485
بەراوردکردن لەگەڵ MAX3490AEGSA+T →
Analog Devices
Product Type: Full-duplex RS-485/RS-422 transceiver
Supply Voltage: 3.3 V nominal
بەراوردکردن لەگەڵ MAX3490AEGSA+T →
Analog Devices
ESD Protection: ±15 kV
Maximum Data Rate: 12 Mbps
بەراوردکردن لەگەڵ MAX3490AEGSA+T →

MAX3490ECSA-T

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin SOIC
No key interface-rate difference identified: both are 20Mbps-class MAX3490 parts in 8-pin SOIC; temperature-grade suffix differs

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3490AEGSA+T تایبەتمەندییەکان

Product Type RS-485/RS-422 transceiver
ڤۆڵتیەی دابینکردن 3.3 V
Maximum Data Rate 20 Mbps
ESD Protection ±20 kV
Driver Count 1 driver
Receiver Count 1 receiver
Supported Standards RS-485 and RS-422
Driver Type Slew-rate limited
پاکێج 8-pin SOIC
جۆری دامەزراندن Surface mount

ڕێنمایی ڕێکخستنی پینی MAX3490AEGSA+T 8-pin soic

ڕێکخستنی پین بۆ MAX3490AEGSA+T (پاکێجی 8-pin soic). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-pin soic بۆ MAX3490AEGSA+T

هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3490AEGSA+T.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

MAX3490AEGSA+T گونجاوە بۆ 6 بەکارھێنانs: Industrial Control Networks, Building Automation Equipment, Telecommunications Data Links, Instrumentation and Test Equipment, EMI-Sensitive RS-422 Connections, External Equipment and Peripheral Links.

🏭

Industrial Control Networks

The MAX3490AEGSA+T fits industrial control nodes that require noise-resistant differential communication over cables running between controllers, sensors, and remote equipment. Its 3.3V supply supports modern controller I/O, while one driver and one receiver provide the fundamental node functions for an RS-485 bus. The 20Mbps capability leaves ample performance headroom for factory automation networks operating well below that limit. Its slew-rate-limited driver also helps reduce EMI and ringing where industrial cabling causes reflections. The key engineering checks are cable length, bus topology, termination placement, common-mode range, and grounding rather than peak data rate alone.

🧩

Building Automation Equipment

The MAX3490AEGSA+T is suitable for building automation controllers, room modules, and field interfaces using an RS-485 or RS-422 backbone. Its differential signaling helps reject common-mode noise encountered near motors, relays, lighting equipment, and long installed cables. A 3.3V operating supply simplifies integration with low-voltage controller logic, while the 8-pin SOIC package keeps the footprint compact for densely populated automation boards. The slew-rate-limited output reduces edge energy and can improve interoperability in equipment networks where cable lengths and terminations vary. Firmware must also support the baud rate, idle state, and bus direction timing required by the installed network.

🌐

Telecommunications Data Links

The MAX3490AEGSA+T can support point-to-point RS-422 links in telecommunications and distributed equipment where logic isolation from cable noise is important. The 3.3V supply fits modern line-card logic, and the 20Mbps maximum data rate accommodates fast control, status, or supervisory channels. Its slew-rate-limited transmitter reduces unwanted high-frequency content compared with an unrestricted edge rate, while ±20kV ESD protection adds useful interface ruggedness. For deployed equipment, verify the supported cable length at the selected baud rate and ensure that grounding or isolation is designed to keep common-mode voltage within the receiver's permitted range.

🔧

Instrumentation and Test Equipment

The MAX3490AEGSA+T is well suited to instrumentation, test systems, and measurement modules that exchange commands or data over a robust differential bus. The combination of a 3.3V supply, 20Mbps capability, and slew-rate-limited output allows the interface to support factory test rates while limiting cable ringing. One transmitter and one receiver provide a practical half-duplex node arrangement for RS-485, while RS-422 operation supports point-to-point links with independent differential signaling. Designers should characterize the complete cable and termination network at the intended baud rate, especially when long leads, adapters, or laboratory equipment introduce discontinuities.

📡

EMI-Sensitive RS-422 Connections

The MAX3490AEGSA+T addresses EMI-sensitive point-to-point links because its slew-rate-limited driver lowers edge energy and helps reduce ringing and radiated harmonics. According to the Analog Devices MAX3490 documentation, this characteristic can improve transmission integrity when cables are imperfectly terminated. The 20Mbps rating supports high-speed communication, while the 8-pin SOIC package keeps the transceiver close to a connector or equipment edge. A successful implementation still requires controlled-impedance routing, a continuous reference plane, appropriate termination, and connector shielding. ESD protection helps with electrostatic events but does not replace normal surge and lightning protection.

🖥️

External Equipment and Peripheral Links

The MAX3490AEGSA+T can provide a compact communication interface between a controller and external equipment operating from a 3.3V logic rail. The 8-pin SOIC package supports automated board assembly while providing the driver and receiver needed for a single bus node. A maximum rate of 20Mbps enables high-throughput data transfers or low-latency command traffic, and the slew-rate-limited output helps control reflections on practical cable assemblies. Choose the operating mode, termination, and logic polarity appropriate for a half-duplex RS-485 network or a full-duplex RS-422 connection. Confirm timing against the attached equipment before releasing the system design.

What is the MAX3490AEGSA+T?
The MAX3490AEGSA+T is a 3.3V-powered RS-485/RS-422 interface IC containing one driver and one receiver. According to the Analog Devices MAX3490 product page and datasheet, it supports operation up to 20Mbps and provides ±20kV ESD protection. The device is packaged for surface-mount assembly in an 8-pin SOIC.
What are the key specifications of MAX3490AEGSA+T that engineers should know?
The MAX3490AEGSA+T operates from a 3.3V supply and supports RS-485 and RS-422 differential signaling. Its principal interface characteristics include one transmitter, one receiver, a maximum data rate of 20Mbps, slew-rate-limited operation, and ±20kV ESD protection. According to the Analog Devices MAX3490 datasheet, these features suit both high-speed links and EMI-conscious industrial communications.
Where can I download the MAX3490AEGSA+T datasheet PDF?
The MAX3490AEGSA+T datasheet is available through the Analog Devices MAX3490 product page, which links to the MAX3490 Data Sheet (Rev. 2). Use that manufacturer document for the complete electrical characteristics, pin descriptions, timing diagrams, and application information. The +T ordering suffix does not change the underlying MAX3490A interface architecture.
Where can I find the MAX3490AEGSA+T pinout?
Use the pin-description table and package drawing in the Analog Devices MAX3490 datasheet to identify every MAX3490AEGSA+T connection. The component is offered in an 8-pin SOIC package, but signal names and no-connect positions must be assigned from the manufacturer pin table. Follow the same pin numbering convention when comparing it with the MAX3490ECSA-T replacement candidate.
Can MAX3490AEGSA+T replace MAX3490ECSA-T?
The MAX3490ECSA-T is the closest documented same-package replacement candidate for the MAX3490AEGSA+T. According to the Analog Devices MAX3490 family documentation and the published cross-reference comparison, both use the 8-pin SOIC format and belong to the same MAX3490 interface family. Confirm the exact operating-temperature grade, supply limits, and lifecycle requirements before production substitution.
What is the best drop-in replacement for MAX3490AEGSA+T?
The MAX3490ECSA-T is the best-supported drop-in replacement candidate because it is explicitly compared with the MAX3490AEGSA+T and uses the same 8-pin SOIC package. No additional cross-brand candidate has been established with sufficient package and parametric confirmation. Before replacing the device, verify temperature-grade limits, enable and receiver-control behavior, and ESD requirements against the manufacturer datasheet.
What can replace MAX3490AEGSA+T?
The MAX3490ECSA-T can serve as a replacement candidate in an existing 8-pin SOIC design because it is explicitly cross-referenced to the MAX3490AEGSA+T. This recommendation is limited to drop-in considerations; board changes are not assumed. Validate production temperature grade, availability, and all timing and electrical limits in the Analog Devices datasheet before approving the substitution.
Is MAX3490AEGSA+T suitable for industrial control networks?
Yes, the MAX3490AEGSA+T is suitable for industrial control networks requiring differential RS-485 or RS-422 communication. According to the Analog Devices MAX3490 documentation, its slew-rate-limited driver reduces EMI and reflections, while its 20Mbps capability supports high-speed links. Cable length, topology, termination, grounding, and surge protection must be evaluated for each installation.
How does MAX3490AEGSA+T handle EMI and cable reflections?
The MAX3490AEGSA+T uses a slew-rate-limited driver to reduce high-frequency harmonics and ringing on the differential bus. According to the Analog Devices MAX3490 product description, this behavior minimizes EMI and reduces reflections caused by improperly terminated cables. Proper impedance-controlled routing and termination remain necessary for reliable operation at high data rates.
Where can I buy MAX3490AEGSA+T online?
Use the Request a Quote form on this XAIPART product page to request the MAX3490AEGSA+T, current lead time, stock status, and order quantities. The +T part is the tape-and-reel production format. Provide the required quantity and destination when submitting the request so the order can be reviewed against current availability.
What is the price of MAX3490AEGSA+T?
The current MAX3490AEGSA+T price is not published as a static figure on this page. Use the Request a Quote form on this XAIPART product page to request a quantity-specific quotation and current availability. The request should include your order quantity, shipment destination, and any required production or traceability documentation.
What is the lead time for MAX3490AEGSA+T?
Current lead time for the MAX3490AEGSA+T should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, stock position, and required packaging. The +T suffix denotes the tape-and-reel ordering form, so include that exact MPN when requesting an order quotation.
Is MAX3490AEGSA+T in stock?
Current inventory status for the MAX3490AEGSA+T should be confirmed through the Request a Quote form on this page. The exact quantity available can change independently of the device's active lifecycle status. Submit the required order quantity and target delivery location to receive a current availability and lead-time response.
When should I choose MAX3490AEGSA+T over MAX3490ECSA-T?
Choose the MAX3490AEGSA+T when its ordering grade and production status align with the target application, and use the MAX3490ECSA-T when its specific temperature and commercial conditions better match the build. According to the manufacturer family documentation, both provide the same 8-pin SOIC interface platform. Review the exact suffix ratings before making a final substitution.
Can a different manufacturer's part replace MAX3490AEGSA+T?
Do not assume that a different manufacturer's transceiver is drop-in compatible with the MAX3490AEGSA+T. A valid replacement must match the 8-pin SOIC footprint, preserve the 3.3V interface, and meet the required RS-485/RS-422 data-rate and ESD specifications. No cross-brand substitute is established here with enough evidence to claim pin-to-pin equivalence.

داتای سەرچاوەی ئەندازیاری بۆ MAX3490AEGSA+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the MAX3490AEGSA+T when the design requires a 3.3V RS-485/RS-422 node with one driver, one receiver, 20Mbps-class operation, slew-rate-limited edges, and ±20kV ESD protection. The MAX3490ECSA-T is the closest documented drop-in candidate because it shares the MAX3490 family and 8-pin SOIC package; select it when its temperature grade, lifecycle status, and commercial terms better fit the production program. Do not substitute a lower-speed RS-485 part solely because it uses SOIC, as its driver timing, propagation delay, and EMI behavior may differ substantially. Likewise, require verified pin mapping, electrical limits, and ESD performance before approving any cross-brand device. For new RS-422 point-to-point links, confirm receiver enable behavior and whether the application needs true full duplex; for multidrop RS-485, verify direction-control timing, idle bias, termination, and supported cable length.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX3490ECSA-T
Package 8-pin SOIC 8-pin SOIC
Brand Analog Devices Analog Devices
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver
Supply Voltage 3.3 V 3.3 V
Maximum Data Rate 20 Mbps 20 Mbps
ESD Protection ±20 kV ±20 kV
Driver Count 1 driver 1 driver
Receiver Count 1 receiver 1 receiver
Driver Edge Rate Slew-rate limited Slew-rate limited
Ordering Suffix AEGSA+T tape-and-reel form ECSA-T tape-and-reel form

جیاکەرەوە سەرەکییەکان

  • High-speed 3.3V interface operation (بەراورد بەMAX3490ECSA-T)
  • Matched 8-pin SOIC footprint (بەراورد بەMAX3490ECSA-T)
  • Integrated interface ruggedness (بەراورد بەMAX3490ECSA-T)

تێبینییەکانی دیزاین

Route the RS-485 or RS-422 driver and receiver traces as a closely coupled differential pair with continuous reference-plane support. Place the transceiver near the connector to minimize exposed stub length, and match trace impedance to the cable. Keep switching or high-current return paths away from the differential pair because common-mode coupling can reduce receiver margin even when the waveform appears clean at the transmitter.

Do not treat the 20Mbps headline rate as a guarantee for every cable length. The usable rate depends on cable loss, topology, stubs, termination, baud rate, and receiver timing. For point-to-point RS-422, apply the termination strategy recommended by the manufacturer. For multidrop RS-485, avoid unnecessary stubs and place termination only at the physical endpoints of the main bus.

The slew-rate-limited driver reduces high-frequency edge content, but it does not eliminate radiated emissions. Maintain a continuous ground plane, use a compact ground-return path, secure connector shields, and avoid splitting the ground beneath the interface. If traces leave the board, use twisted-pair cable and consider a connector arrangement that keeps signal and return conductors together to reduce loop area.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance declarations must be confirmed from the current manufacturer product documentation or the relevant declaration for the exact MAX3490AEGSA+T ordering code.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX3490AEGSA+T datasheet MAX3490AEGSA+T pinout MAX3490AEGSA+T datasheet pdf MAX3490AEGSA+T replacement MAX3490AEGSA+T equivalent MAX3490AEGSA+T price MAX3490AEGSA+T stock MAX3490AEGSA+T 8-SOIC MAX3490AEGSA+T RS-485 transceiver MAX3490AEGSA+T RS-422 interface MAX3490AEGSA+T vs MAX3490ECSA-T Analog Devices MAX3490AEGSA+T

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices MAX3490AEGSA+T MAX3490 MAX3490ECSA-T RS-485 RS-422 interface transceiver bus transceiver differential signaling slew-rate-limited driver 3.3V power supply 20Mbps data rate ±20kV ESD protection 8-pin SOIC SOIC package family surface-mount technology industrial control network building automation telecommunications equipment EMI cable reflections common-mode rejection semiconductor analog mixed-signal IC
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ