Analog Devices

MAX3490CSA+T 3.3V 10Mbps RS-485/RS-422 Transceiver | Analog Devices

MPN: MAX3490CSA+T ✓ چالاک
3.0V to 3.6V Vdss 8-pin SOIC Package
MOQ: 1 |

MAX3490CSA+T گشتی

The Analog Devices MAX3490CSA+T is a 3.3V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, supporting data rates up to 10Mbps in an 8-pin SOIC package. Its low-power architecture is designed for industrial communication links where a compact interface is required for bidirectional serial data.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and converts received differential signals back into logic levels. RS-485 supports multipoint buses with bidirectional communication, while RS-422 provides a point-to-point differential link. The MAX3490CSA+T belongs to the interface IC family within the broader semiconductor and industrial-control hierarchy.

Key features include operation from a 3.0V to 3.6V supply, a maximum data rate of 10Mbps, one driver and one receiver, and slew-rate-limited operation for reduced EMI and reflection control. The device also includes short-circuit protection and thermal shutdown according to the manufacturer product information. Its 8-SOIC package supports conventional surface-mount PCB assembly.

The MAX3490CSA+T uses true differential RS-485/RS-422 signaling, allowing communication over longer cable runs than single-ended interfaces while improving noise immunity. The receiver supports fail-safe operation when the bus is idle, and the driver places its output in a high-impedance state during thermal shutdown. These characteristics suit industrial controllers, instrumentation, data acquisition systems, and factory automation equipment.

Typical applications include industrial sensor networks, RS-485 motor-control links, building automation equipment, test and measurement instruments, and embedded control systems. The 3.3V supply is convenient for systems built around modern low-voltage processors, while the 10Mbps capability supports higher-speed factory and data-acquisition links.

For PCB design, place the transceiver close to the connector and route the balanced differential pair as a controlled-impedance pair. Connect the bus termination and biasing components according to the system topology, and keep the ground reference continuous between the transceiver and cable interface. Verify the supply voltage, idle-bus behavior, and cable length before releasing the design.

This product page combines the manufacturer’s MAX3490 technical information with practical selection guidance, application positioning, and package-level design considerations. It is intended to help engineers identify the correct transceiver for low-voltage, high-speed RS-485 and RS-422 interfaces without conflating protocol requirements, electrical termination, and PCB layout decisions.

جێگرەوەکانی جێگۆڕکێ بۆ MAX3490CSA+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3490CSA+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Maximum Data Rate, Package, REACH Status, RoHS Status, Supply Voltage.

Analog Devices
Maximum Data Rate: 12 Mbps
REACH Status: unknown
RoHS Status: unknown
بەراوردکردن لەگەڵ MAX3490CSA+T →
Analog Devices
Maximum Data Rate: 10 Mbps
Package: 8-SOIC
REACH Status: Compliant
بەراوردکردن لەگەڵ MAX3490CSA+T →

MAX3490EESA+

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 8-SOIC
RS-485/RS-422 transceiver · 3.3 V · 12 Mbps · ±15 kV · 1 driver · 1 receiver · RS-485 and RS-422 · Slew-rate limited

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3485EESA+

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Analog Devices
📦 8-SOIC
1/1 half-duplex RS-485/RS-422 transceiver · 3.3V · 12Mbps · 1 driver · 1 receiver · RS-485 and RS-422 · Slew-rate-limited true RS-485/RS-422 · ±15kV per IEC 1000-4-2

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3486EESA+

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-SOIC
Same-manufacturer MAX3486-family RS-485/RS-422 transceiver in an 8-SOIC package; speed and protection details must be checked against the target 10Mbps interface.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3488EESA+

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Maxim Integrated
📦 8-SOIC
RS-485/RS-422 transceiver · 3.3 V · 12 Mbps · ±15 kV · 1 · 1 · True differential RS-485/RS-422 · Slew-rate limited

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3491EESA+

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-SOIC
Same-manufacturer MAX3491-family RS-485/RS-422 transceiver in an 8-SOIC package; compare the exact speed, protection, and pin configuration before replacement.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3490CSA+T تایبەتمەندییەکان

Product Type RS-485/RS-422 transceiver
ڤۆڵتیەی دابینکردن 3.0V to 3.6V
Maximum Data Rate 10Mbps
Driver Channel Count 1
Receiver Channel Count 1
Interface Standard RS-485 and RS-422
Communication Mode Full duplex
پاکێج 8-pin SOIC
جۆری دامەزراندن Surface Mount
Driver Output Type True differential
Slew Rate Slew-rate limited
Driver Protection Short-circuit current limited
Thermal Protection Thermal shutdown
Receiver Idle Behavior Fail-safe feature

ڕێنمایی ڕێکخستنی پینی MAX3490CSA+T 8-pin soic

ڕێکخستنی پین بۆ MAX3490CSA+T (پاکێجی 8-pin soic). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-pin soic بۆ MAX3490CSA+T

هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3490CSA+T.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

MAX3490CSA+T گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Networks, Factory Automation Equipment, Data Acquisition Systems, Building Automation Networks, Test and Measurement Instruments, Embedded Control Systems.

🏭

Industrial Sensor Networks

The MAX3490CSA+T fits industrial sensor networks that distribute measurements over a balanced RS-485 bus. Its 3.0V-to-3.6V operating range is appropriate for low-voltage controller boards, while the 10Mbps capability supports high-speed data collection. The single driver and receiver provide the basic physical-layer interface for connecting remote sensors, controllers, and monitoring equipment. Use controlled-impedance routing, continuous grounding, and the termination scheme appropriate for the installed cable length and topology.

🏭

Factory Automation Equipment

Factory automation equipment can use the MAX3490CSA+T to connect a controller to motor drivers, remote I/O modules, and production equipment. The 10Mbps data rate provides bandwidth for status, command, and diagnostic traffic, while the 8-SOIC package supports compact surface-mount designs. The differential interface helps reject common-mode noise encountered near industrial machinery. Confirm cable length, bus topology, isolation requirements, and grounding before selecting the final termination and protection components.

📊

Data Acquisition Systems

The MAX3490CSA+T is appropriate for data-acquisition systems requiring a fast, low-voltage differential serial link between a controller and measurement hardware. Its 10Mbps maximum rate supports transferring sampled data and commands, and the true RS-485/RS-422 operation supports reliable communication over balanced cabling. Keep the differential pair routed away from switching nodes and power inductors, and verify that the sampling architecture does not require isolation beyond the transceiver’s internal capabilities.

🏠

Building Automation Networks

The MAX3490CSA+T can support building automation controllers, HVAC interfaces, and distributed environmental monitoring equipment using an RS-485 backbone. The 3.3V supply matches many embedded controller platforms, while the differential transceiver simplifies communication over building-scale wiring. Designers should select termination based on the number of nodes and cable length, use a fail-safe bias arrangement when required, and maintain a reliable reference ground along the bus.

🔧

Test and Measurement Instruments

The MAX3490CSA+T is useful in test and measurement instruments that exchange commands and results with external fixtures over a short RS-485 or RS-422 link. The 10Mbps capability allows the instrument controller to support faster data transfers, while the compact 8-SOIC package simplifies board-level integration. Place the transceiver near the external connector, add the required protection network, and check that the instrument’s ground and isolation architecture is compatible with the transceiver’s supply and logic levels.

🧩

Embedded Control Systems

The MAX3490CSA+T fits embedded control systems that need to communicate with remote actuators, controllers, or service equipment. Its 3.3V supply is compatible with many microcontroller platforms, and the integrated driver and receiver reduce the external component count for a standard balanced interface. The main design trade-offs are cable-length-dependent termination, possible ground-potential issues in distributed systems, and the need to ensure that the 10Mbps target does not exceed the signal-integrity budget of the selected cabling.

What is the MAX3490CSA+T used for?
The MAX3490CSA+T is a 3.3V-powered RS-485/RS-422 transceiver used to connect a digital controller to a balanced serial bus. It combines one transmitter and one receiver, supports rates up to 10Mbps, and is intended for industrial, instrumentation, automation, and embedded communication systems.
What are the key specifications of MAX3490CSA+T?
The MAX3490CSA+T operates from 3.0V to 3.6V, provides one driver and one receiver, and supports 10Mbps data rates. The device provides true RS-485/RS-422 differential signaling, slew-rate-limited outputs, short-circuit protection, thermal shutdown, and an 8-pin SOIC package.
Is MAX3490CSA+T compatible with RS-485 and RS-422?
Yes. The MAX3490CSA+T supports both RS-485 and RS-422 interfaces according to the manufacturer product information. Its differential driver and receiver provide the electrical interface for balanced industrial communication links, while the protocol and bus topology determine the required termination and biasing arrangement.
What is the supply voltage range of MAX3490CSA+T?
The MAX3490CSA+T operates from a 3.0V to 3.6V supply, making it suitable for 3.3V system rails. The supply range is one of the key selection constraints because the transceiver is specifically described as a 3.3V-powered device, and its interface timing and protection behavior must be evaluated within that range.
What is the maximum data rate of MAX3490CSA+T?
The MAX3490CSA+T supports data rates up to 10Mbps. This makes it suitable for higher-speed RS-485 and RS-422 links used in industrial equipment, factory automation, and data-acquisition systems, provided that the cable, termination, topology, and signal-integrity design support the selected operating rate.
Where can I find the MAX3490CSA+T datasheet?
The official MAX3490 product page is available at analog.com/en/products/max3490.html. It links to the manufacturer’s MAX3490 data sheet and product documentation, including the electrical characteristics and package information needed to confirm the 3.3V operation, 10Mbps capability, and 8-SOIC footprint.
Where is the MAX3490CSA+T pinout?
Use the pin-description table and package drawing in the official MAX3490 manufacturer data sheet for the exact 8-SOIC pin assignment. The available technical information confirms the 8-SOIC package and full-duplex transceiver function, but a complete numbered pin list is not included here.
Can MAX3490EESA+ replace MAX3490CSA+T?
MAX3490EESA+ is a same-manufacturer MAX3490-family option in an 8-SOIC package, so it is the closest identified drop-in candidate. The comparison should confirm supply range, data rate, ESD protection, and exact pin assignment before substitution, because those details determine whether the existing board layout and protection design remain unchanged.
What is the best drop-in replacement for MAX3490CSA+T?
The best drop-in replacement should preserve the 8-SOIC footprint, pin-to-pin behavior, 3.0V-to-3.6V supply range, and approximately 10Mbps RS-485/RS-422 performance. MAX3490EESA+ is the strongest identified same-family candidate, while any cross-brand substitute must be checked against the manufacturer pinout and electrical characteristics before use.
What can replace MAX3490CSA+T?
A suitable replacement must be a surface-mount 8-SOIC transceiver with compatible RS-485/RS-422 differential I/O, a 3.3V operating range, and comparable speed. MAX3490EESA+ is the most directly comparable identified option; validate its pinout, ESD rating, driver loading, fail-safe behavior, and shutdown implementation against the original design.
How does MAX3490CSA+T differ from MAX3490EESA+?
Both devices are identified in the MAX3490 family and use an 8-SOIC package, but the MAX3490EESA+ is associated with an enhanced ESD-protected variant and a 12Mbps rating in the manufacturer product search results. The original MAX3490CSA+T is listed at 10Mbps, so speed and protection requirements should guide final substitution.
When should I choose MAX3490CSA+T instead of a lower-speed RS-485 transceiver?
Choose MAX3490CSA+T when the interface must operate at up to 10Mbps and the bus design can preserve signal integrity at that rate. A lower-speed transceiver may be preferable for short, slow links where reduced EMI, relaxed timing, or lower power is more important than maximum throughput.
Is MAX3490CSA+T suitable for industrial automation equipment?
The MAX3490CSA+T is suitable for industrial automation interfaces that require a 3.3V-powered differential RS-485 or RS-422 link up to 10Mbps. Its slew-rate-limited driver, thermal shutdown, short-circuit protection, and fail-safe receiver behavior support robust bus designs when the PCB layout, termination, grounding, and cable requirements are also satisfied.
What is the lead time for MAX3490CSA+T?
Lead time depends on the current inventory and order quantity, so request the latest confirmation through the Request a Quote form on this page. The product is identified as an Analog Devices MAX3490 family transceiver and is offered in the 8-SOIC package, but a current manufacturing schedule should be confirmed for the exact MAX3490CSA+T ordering code.
Where can I buy MAX3490CSA+T online?
Use the Request a Quote form on this page to request the current price, stock position, packaging, and lead time for MAX3490CSA+T. This request is the appropriate route for an order-specific commercial response because inventory and commercial terms can change by quantity and date.
Is MAX3490CSA+T in stock?
The current stock status for MAX3490CSA+T should be confirmed through the Request a Quote form on this page. The manufacturer lists the MAX3490 family as production, but an exact stock answer depends on the suffix, package, order quantity, and current supply status.
Does MAX3490CSA+T meet RoHS and REACH requirements?
The RoHS and REACH status of MAX3490CSA+T should be confirmed from the current manufacturer product documentation and declarations for the exact ordering code. Those compliance statements are not included in the technical excerpts available for this product, so no definitive certification claim should be made without the manufacturer’s declaration.

داتای سەرچاوەی ئەندازیاری بۆ MAX3490CSA+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose MAX3490CSA+T when the design needs a 3.3V-powered, surface-mount 8-SOIC transceiver for RS-485 or RS-422 communication at rates up to 10Mbps. It is a strong fit for industrial controllers, data-acquisition equipment, embedded systems, and building automation links where differential signaling and a compact package are important. Choose MAX3490EESA+ when the board can benefit from the identified enhanced variant’s 12Mbps rating and ±15kV ESD protection, after confirming its exact pin and electrical requirements. Consider MAX3488EESA+ only when lower-speed operation is acceptable and the reduced performance requirement is justified. The MAX3485EESA+, MAX3486EESA+, and MAX3491EESA+ options require direct checking of speed, supply, protection, and pin details before substitution. Always verify the exact ordering code, cable topology, termination, grounding, and system isolation requirements.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX3490EESA+ MAX3485EESA+ MAX3486EESA+ MAX3488EESA+ MAX3491EESA+
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Interface RS-485/RS-422 RS-485/RS-422 RS-485/RS-422 RS-485/RS-422 RS-485/RS-422 RS-485/RS-422

جیاکەرەوە سەرەکییەکان

  • 10Mbps maximum data rate (بەراورد بەMAX3488EESA+)
  • Enhanced same-family alternative with higher speed (بەراورد بەMAX3490EESA+)
  • Compact 8-SOIC integration (بەراورد بەMAX3491EESA+)

تێبینییەکانی دیزاین

Route the RS-485/RS-422 differential pair as a tightly coupled pair, keep its length short from the transceiver to the connector, and maintain continuous ground beneath and alongside the pair. Avoid routing through switching-power areas or across high-current return paths. Place the external protection and termination components near the connector so transient energy is diverted before reaching the transceiver pins.

The MAX3490CSA+T supports data rates up to 10Mbps, but the usable rate also depends on cable loss, reflections, topology, and node spacing. Add the appropriate termination at the physical ends of the bus and use bias resistors only when the transceiver family’s fail-safe requirements call for them. Validate the complete board-and-cable channel with an eye diagram or receiver-error-rate test.

Provide a stable 3.0V-to-3.6V supply and decouple the transceiver close to its supply pins with the capacitance recommended by the manufacturer’s application guidance. Keep the ground return path short and connect it directly to the system ground plane. Do not assume that the transceiver’s protection features eliminate the need for correctly selected external surge and ESD protection for exposed cables.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The product information identifies the MAX3490 family as production but does not provide the exact RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for MAX3490CSA+T.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX3490CSA+T datasheet MAX3490CSA+T pinout MAX3490CSA+T datasheet pdf MAX3490CSA+T equivalent MAX3490CSA+T replacement MAX3490CSA+T vs MAX3490EESA+ MAX3490CSA+T 3.3V 10Mbps MAX3490CSA+T RS-485 RS-422 MAX3490CSA+T 8-SOIC MAX3490CSA+T price MAX3490CSA+T stock Analog Devices MAX3490CSA+T MAX3490CSA+T industrial transceiver MAX3490CSA+T schematic MAX3490 8-SOIC pinout

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices Maxim Integrated MAX3490CSA+T MAX3490 MAX3490EESA+ MAX3485EESA+ MAX3486EESA+ MAX3488EESA+ MAX3491EESA+ RS-485 RS-422 transceiver interface IC differential signaling 3.3V powered 10Mbps 8-SOIC surface-mount slew-rate-limited driver thermal shutdown fail-safe receiver industrial automation data acquisition embedded control EMI control
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ