MCP2515-E/ST - 1 Mbps CAN 2.0B Controller | Microchip Technology
MPN: MCP2515-E/ST ✓ چالاکMCP2515-E/ST گشتی
A CAN controller is a serial communications device that places formatted messages onto a Controller Area Network bus. The MCP2515 handles frame encoding, arbitration, error detection, acknowledgment, and retry while a separate CAN transceiver converts the controller's logic-level TXD and RXD signals into the physical CANH and CANL bus lines. This separation allows the controller to work with different transceivers and bus topologies.
Key features include CAN 2.0B protocol support, a maximum bit rate of 1 Mbps, and an SPI interface suitable for connection to microcontrollers, industrial controllers, and embedded systems. The device can receive and transmit standard and extended identifiers as well as remote frames. Its 3.3 V or 5 V operation supports both modern low-voltage digital systems and established 5 V CAN equipment.
The MCP2515-E/ST is the extended-temperature version of the MCP2515 family, supplied in a 20-pin TSSOP for surface-mount assembly. Distributor listings identify the MCP2515T-E/ST as the corresponding tape-and-reel ordering option, while the MCP2515-E/ST suffix denotes the tube-packaged form. The exact electrical limits, pin functions, timing values, and environmental ratings should be confirmed against the Microchip MCP2515 Family Data Sheet.
Typical applications include industrial automation, vehicle and equipment networking, elevator controls, robotics, building automation, and embedded CAN gateways. Because the MCP2515 is a controller rather than a transceiver, a compatible CAN transceiver such as the TJA1050 or a 3.3 V transceiver must be added to interface with a physical CAN bus.
When laying out the circuit, place the controller and transceiver close enough to minimize the TXD and RXD interconnect, provide a stable clock for the SPI host interface, and route the CANH and CANL bus traces as a differential pair. Verify termination, common-mode voltage, and ground strategy for the selected transceiver rather than treating the MCP2515 as a complete bus node.
This page consolidates manufacturer protocol information, distributor package and pricing references, same-footprint family alternatives, and practical selection guidance that is not consolidated on ordinary distributor listings.
جێگرەوەکانی جێگۆڕکێ بۆ MCP2515-E/ST — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCP2515-E/ST (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Operating Temperature, Host Interface, Supported Frame Types, CAN Specification.
MCP2515-I/ST
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515T-I/ST
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515-E/STVAO
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515-I/STVAO
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515T-E/ST
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515-E/ST تایبەتمەندییەکان
| Device Type | Stand-alone CAN controller |
| CAN Protocol Version | CAN 2.0B |
| Maximum CAN Bit Rate | 1 Mbps |
| Host Interface | SPI |
| Supported Frame Types | Standard data frames, extended data frames, and remote frames |
| ڤۆڵتیەی دابینکردن | 3.3 V or 5 V |
| پاکێج | 20-pin TSSOP |
| جۆری دامەزراندن | Surface mount |
| Ordering Package | Tube |
| CAN Transceiver Functions | Not integrated; external CAN transceiver required |
ڕێنمایی ڕێکخستنی پینی MCP2515-E/ST tube
ڕێکخستنی پین بۆ MCP2515-E/ST (پاکێجی tube). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MCP2515-E/ST.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MCP2515-E/ST گونجاوە بۆ 6 بەکارھێنانs: Industrial Automation CAN Nodes, Vehicle and Equipment Networking, Robotics and Motor-Control Coordination, Building Automation and HVAC Control, Embedded CAN Gateways, Elevator and Material-Handling Controls.
Industrial Automation CAN Nodes
The MCP2515-E/ST fits industrial automation nodes that exchange standard, extended, or remote CAN frames at rates up to 1 Mbps. Its SPI interface connects efficiently to a microcontroller, while the separate transceiver permits selection of the bus protection and voltage level required by the installation. Use separate logic and bus-ground planning where required by the transceiver, and validate bit timing against the network's oscillator and sample-point settings before production release.
پێشنیارکراو
Vehicle and Equipment Networking
The MCP2515-E/ST is suitable for equipment modules that need a dedicated CAN 2.0B controller rather than a combined controller-transceiver package. Its 1 Mbps maximum rate supports legacy CAN networks, while standard and extended identifiers allow coexistence of priority-based control traffic and diagnostic information. Automotive-qualified variants can be considered where the vehicle program requires them, but the base E/ST ordering code should be checked against the required qualification and temperature range.
پێشنیارکراو
Robotics and Motor-Control Coordination
Robot controllers can use the MCP2515-E/ST to coordinate actuators, sensors, and safety-related status messages over a shared CAN bus. The SPI host interface simplifies firmware-driven frame filtering and transmission, and the 20-pin TSSOP leaves board area for the required external transceiver and protection network. Design the bus with correct termination, a differential CANH/CANL trace pair, and firmware that responds to the network's arbitration and error-management rules.
پێشنیارکراو
Building Automation and HVAC Control
The MCP2515-E/ST supports building-automation controllers that distribute HVAC commands, sensor readings, and equipment status across a CAN network. Because it accepts standard and extended frames and supports remote frames, it can participate in systems using different identifier conventions. The device's 3.3 V or 5 V supply range permits integration with either controller logic family, although the external transceiver and its isolation strategy must match the building wiring.
پێشنیارکراو
Embedded CAN Gateways
The MCP2515-E/ST is appropriate for gateway modules that translate between an SPI-connected processor and an external CAN bus. Its stand-alone controller architecture lets engineers choose the transceiver independently, which is useful when the gateway must support different bus voltage levels, isolation requirements, or protection ratings. Because it is controller-only, gateway bring-up must include transceiver timing checks, bus termination validation, and fault-injection testing of CAN error states.
پێشنیارکراو
Elevator and Material-Handling Controls
The MCP2515-E/ST can connect elevator drives, door controllers, and material-handling modules to a common CAN communications backbone. Its 1 Mbps capability handles standard industrial CAN traffic, while the SPI interface allows a local microcontroller to manage message identifiers and filters. The controller should be paired with a transceiver selected for the cable length and environment, and firmware should include safe handling for bus-off recovery and unexpected loss of communication.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MCP2515-E/ST — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MCP2515-I/ST | MCP2515T-I/ST | MCP2515-E/STVAO | MCP2515-I/STVAO | MCP2515T-E/ST |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP |
| CAN Protocol | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B |
| Maximum Bit Rate | 1 Mbps | 1 Mbps | 1 Mbps | 1 Mbps | 1 Mbps | 1 Mbps |
| Host Interface | SPI | SPI | SPI | SPI | SPI | SPI |
| Supported Frame Types | Standard, extended, and remote frames | Standard, extended, and remote frames | Standard, extended, and remote frames | Standard, extended, and remote frames | Standard, extended, and remote frames | Standard, extended, and remote frames |
| Ordering Format | E/ST tube-packaged ordering code | I/ST industrial-grade tube ordering code | T/I/ST industrial-grade tape-and-reel ordering code | E/ST VAO automotive ordering code | I/ST VAO automotive ordering code | T/E/ST extended-grade tape-and-reel ordering code |
| External Transceiver Requirement | Required | Required | Required | Required | Required | Required |
جیاکەرەوە سەرەکییەکان
- Controller and transceiver remain independently selectable (بەراورد بەTCAN4550-Q1)
- Extended E-grade ordering option in the same 20-pin TSSOP family (بەراورد بەMCP2515-I/ST)
- Automotive-qualified family alternatives retain the same footprint (بەراورد بەMCP2515-E/STVAO)
تێبینییەکانی دیزاین
The MCP2515-E/ST is a controller, so its PCB must include an external CAN transceiver and the associated protection network. Place the controller and transceiver near one another, keep the TXD and RXD logic routes short, and route CANH and CANL together as a differential pair with controlled impedance. Provide transceiver supply decoupling and a chassis or shield-ground strategy appropriate to the installation. Verify the final layer stack and termination placement against the selected transceiver's reference layout.
SPI timing must be validated with the actual host clock, trace length, and MCP2515 configuration. The verified data confirms SPI connectivity and a 1 Mbps CAN rate, but it does not provide a maximum SPI clock value; obtain that limit from the Microchip family data sheet before setting firmware delays. In a 3.3 V system, confirm that every connected device and the selected transceiver use compatible logic levels instead of assuming that 3.3 V and 5 V operation are interchangeable.
Do not treat MCP2515 TXD or RXD as physical CAN bus pins, and do not connect them directly to CANH or CANL. A separate transceiver is required for differential bus signaling. Also verify termination: only the intended ends of the CAN network should normally carry 120-ohm termination. Firmware should implement filters, correct bit timing, and bus-off recovery because a pin-compatible package alone does not guarantee identical software behavior.
The MCP2515-E/ST and MCP2515T-E/ST differ in the documented supplier ordering format: tube versus tape-and-reel. Prototype builders should use the tube version where appropriate, while automated assembly should order the tape-and-reel code after confirming the same electrical device and footprint. Do not substitute MCP2515-I/ST or a VAO automotive suffix solely because the package looks identical; first compare temperature range, qualification, and supply-chain requirements.
زانیاری پابەندبوون
The supplied web results do not explicitly state the base MCP2515-E/ST's RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Automotive VAO family variants are distinguished by their automotive ordering codes, but this does not establish the qualification status of the base E/ST part.