MCP2515T-E/ST - 1 Mbps CAN 2.0B Controller | Microchip Technology
MPN: MCP2515T-E/ST ✓ چالاکMCP2515T-E/ST گشتی
A CAN controller is a communications IC that converts host commands into CAN frames and converts received CAN traffic into data available through a serial interface. Within the broader hierarchy, the MCP2515T-E/ST is a CAN interface controller and therefore belongs to the interface IC, CAN controller, industrial communication, and embedded networking domains. It connects a microcontroller or other host processor to a CAN bus through an external CAN transceiver.
The second-generation MCP2515 architecture provides faster throughput, byte-level filtering, and support for time-triggered protocols. According to the Microchip Technology MCP2515 family datasheet, it can both transmit and receive standard, extended, and remote frames. Its SPI interface allows register configuration, interrupt handling, and frame exchange with a host microcontroller while keeping the CAN physical-layer implementation in a separate transceiver.
The MCP2515T-E/ST operates from a 3.3 V or 5 V supply in Sleep and Standby modes, and the associated component listing identifies a maximum operating temperature of 125°C. It is intended for both 3.3 V and 5 V embedded systems and supports designs that require reception filters, interrupt-driven bus management, or scheduled time-triggered communication.
Typical applications include industrial automation equipment, automotive and transportation modules, building-control systems, robotics, medical instruments, and embedded data-acquisition equipment. It is especially suitable when an existing host controller already uses SPI and the design needs a dedicated CAN protocol engine instead of implementing CAN framing in host software.
The principal design consideration is that the MCP2515T-E/ST is a controller, not a CAN transceiver. The PCB therefore needs a suitable 3.3 V or 5 V CAN transceiver, proper bus termination, protection appropriate to the environment, and a carefully routed connection between the controller and transceiver. Firmware must also initialize the bit timing, configure acceptance filters, select clock and interrupt settings, and handle bus-off recovery according to the device register definitions.
جێگرەوەکانی جێگۆڕکێ بۆ MCP2515T-E/ST — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCP2515T-E/ST (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Operating Temperature, Host Interface, CAN Specification, Supply Voltage.
MCP2515T-I/ST
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515-E/STVAO
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515-I/ST
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515T-E/ST تایبەتمەندییەکان
| Product Type | Stand-alone CAN controller |
| CAN Specification | CAN version 2.0B |
| Maximum CAN Data Rate | 1 Mbit/s |
| Host Interface | SPI |
| Supported Frame Types | Standard, extended data, and remote frames |
| ڤۆڵتیەی دابینکردن | 3.3 V or 5 V |
| پاکێج | 20-pin TSSOP |
| جۆری دامەزراندن | Surface mount |
| پلەی گەرمیی کارکردن | Up to 125°C |
| Controller Generation | Second generation |
| Filtering | Data-byte filtering |
| Protocol Support | Time-triggered protocols |
| Compatibility | Pin and function compatible with MCP2510 |
| Operating Modes | Sleep and Standby |
ڕێنمایی ڕێکخستنی پینی MCP2515T-E/ST 20-pin tssop
ڕێکخستنی پین بۆ MCP2515T-E/ST (پاکێجی 20-pin tssop). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MCP2515T-E/ST.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MCP2515T-E/ST گونجاوە بۆ 6 بەکارھێنانs: Industrial PLC and Automation Controller, Automotive and Transportation Module, Robotics Sensor and Actuator Network, Medical Instrument Data Interface, Building Control and HVAC Gateway, Embedded Data Acquisition and Test Equipment.
Industrial PLC and Automation Controller
The MCP2515T-E/ST fits industrial automation modules that must exchange cyclic process data over a CAN bus while a host microcontroller handles sequencing and user-interface tasks. Its dedicated CAN 2.0B engine supports standard and extended frames up to 1 Mbit/s, offloading bit stuffing, arbitration, framing, and acknowledgments from the host processor. The SPI host interface simplifies connection to a microcontroller, while acceptance filters reduce the number of frames transferred over SPI. Add an industrial-rated transceiver, surge protection, isolated power where required, and firmware for bus-off recovery before deployment in factory equipment.
پێشنیارکراو
Automotive and Transportation Module
The MCP2515T-E/ST is appropriate for body, sensor, gateway, or transportation modules that use CAN for distributed control and diagnostic communication. The device supports CAN 2.0B standard and extended identifiers, remote frames, byte filtering, and time-triggered protocols, providing the communication engine needed for a host processor. Its listing identifies operation up to 125°C, which supports many elevated-temperature environments, although the complete module must still meet its own qualification requirements. Pair the controller with an automotive-appropriate transceiver and implement the bus fault, sleep, wake, and bus-off behavior required by the vehicle network specification.
پێشنیارکراو
Robotics Sensor and Actuator Network
The MCP2515T-E/ST can serve as the CAN protocol engine in robot controllers, sensor hubs, motor modules, and actuator nodes. A host microcontroller configures bit timing and filters through SPI, allowing the controller to manage CAN arbitration and frame transfer while firmware handles robotics control functions. Standard and extended frame support allows related nodes to use identifier conventions suited to their priority and addressing needs. For long cable runs and electrically noisy environments, use a transceiver with suitable transient immunity, place protection close to connectors, and verify termination placement on each CAN segment.
پێشنیارکراو
Medical Instrument Data Interface
The MCP2515T-E/ST can be used in medical laboratory instruments and diagnostic equipment that need reliable communication between an embedded controller and external modules. Its dedicated CAN 2.0B controller handles standard, extended, and remote frames, while data-byte filters help the host process only relevant identifiers. The SPI interface permits deterministic register access and interrupt-driven frame reception in embedded firmware. Medical designs should pair the controller with a transceiver appropriate for the required isolation and cable environment, define safe bus-off recovery behavior, and complete all system-level safety and regulatory validation rather than inferring it from the controller qualification alone.
پێشنیارکراو
Building Control and HVAC Gateway
The MCP2515T-E/ST is suitable for HVAC controllers, room modules, and building-control gateways that distribute operating data over a CAN-based field bus. Its 1 Mbit/s capability supports modern network traffic, and programmable filters help the host isolate configuration, diagnostic, and sensor traffic by identifier. Low-power Sleep and Standby operation can support systems where the node must reduce consumption between activity periods. Select a transceiver and protection scheme suited to the building wiring, define deterministic shutdown and restart behavior, and validate bit timing across every operating temperature expected in the installed equipment.
پێشنیارکراو
Embedded Data Acquisition and Test Equipment
The MCP2515T-E/ST fits laboratory and field-test systems that collect or distribute measurement data over CAN. A laboratory host or embedded processor can use the SPI interface to configure acceptance masks, read error counters, and retrieve frames through interrupts. Remote frames and extended identifiers add flexibility for instrument addressing and diagnostic commands, while time-triggered protocol support suits synchronized acquisition networks. Keep the CAN controller clock and bit-timing configuration consistent with the selected transceiver, isolate long cable interfaces as required, and use repeatable termination and grounding to prevent reflections from corrupting measurements.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MCP2515T-E/ST — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MCP2515T-I/ST | MCP2515-E/ST | MCP2515-I/ST |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TSSOP-20 | TSSOP-20 - same footprint | TSSOP-20 - same footprint | TSSOP-20 - same footprint |
| Controller Function | Stand-alone CAN controller | Stand-alone CAN controller | Stand-alone CAN controller | Stand-alone CAN controller |
| CAN Specification | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B |
| Maximum Data Rate | 1 Mbit/s | 1 Mbit/s | 1 Mbit/s | 1 Mbit/s |
| Host Interface | SPI | SPI | SPI | SPI |
| Supported Frame Types | Standard, extended data, and remote frames | Standard, extended data, and remote frames | Standard, extended data, and remote frames | Standard, extended data, and remote frames |
| Supply Voltage | 3.3 V or 5 V | 3.3 V or 5 V | 3.3 V or 5 V | 3.3 V or 5 V |
| Filtering | Data-byte filtering | Data-byte filtering | Data-byte filtering | Data-byte filtering |
| Protocol Features | Time-triggered protocol support | Time-triggered protocol support | Time-triggered protocol support | Time-triggered protocol support |
جیاکەرەوە سەرەکییەکان
- Dedicated CAN 2.0B protocol engine with extended-frame support (بەراورد بەMCP2515T-I/ST)
- Same-footprint ordering alternative for targeted BOM substitutions (بەراورد بەMCP2515-E/ST)
- SPI-connected standalone controller architecture (بەراورد بەTCAN4550-Q1)
تێبینییەکانی دیزاین
Place the MCP2515T-E/ST close to the SPI host and CAN transceiver, then keep the SPI clock, data, and chip-select tracks short and routed away from the CAN bus and switching-power nodes. The MCP2515 requires an external transceiver; provide clean logic-ground and transceiver-ground connections according to the selected transceiver layout. Maintain the package spacing and land pattern specified for the 20-pin TSSOP, and use the manufacturer pin-description table when assigning every signal.
Configure CAN bit timing for the actual clock source and the propagation delay of the external transceiver. Although the controller supports 1 Mbit/s, the complete bus must also meet that rate within the transceiver, wiring, and termination budget. Avoid long stubs, use the intended 120-ohm termination only at the physical ends of the bus, and keep the CAN differential pair away from clocks, switching inductors, and high-current return paths to reduce susceptibility to reflections and radiated coupling.
Do not treat the MCP2515T-E/ST as a CAN transceiver; connecting it directly to the physical bus omits the driver, receiver, isolation, and protection normally provided by a transceiver. Firmware must also initialize the configuration registers, acceptance masks, interrupt enables, operating mode, and bit-timing values. Implement bus-off status handling, reset behavior, and Sleep or Standby wake logic explicitly instead of assuming that the host processor will recover from network faults automatically.
Keep the SPI bus and sensitive controller traces away from the CAN connector and external protection devices where their return currents could inject noise. Use a continuous ground reference beneath the TSSOP and follow the external transceiver's recommended grounding and decoupling arrangement. For cables leaving an enclosure, place transient-protection components at the connector and provide the isolation, surge, and ESD protection required by the installation environment rather than relying on the controller's digital logic.
زانیاری پابەندبوون
The product listings identify the package, protocol, interface, and operating-temperature information but do not explicitly establish the listed compliance fields.