MCP604-E/SL - 2.8MHz Quad Op Amp | Microchip
MPN: MCP604-E/SL ✓ چالاکMCP604-E/SL گشتی
An operational amplifier, commonly called an op amp, is a high-gain differential amplifier used to amplify, buffer, filter, compare, or control voltage signals. The MCP604 belongs to the operational-amplifier hierarchy within analog integrated circuits and combines four independent amplifier channels in one package, reducing board area and simplifying multi-channel signal paths.
Key features include a 2.8 MHz typical gain-bandwidth product, 2.3 V/us slew rate, unity-gain stability, and low typical operating current of 230 uA. Rail-to-rail input and output behavior permits the amplifier to process signals close to the supply rails, while the CMOS implementation provides low bias current and low static power requirements.
The four amplifier channels share common supply connections but operate independently. This arrangement suits instrumentation, sensor interfaces, filtering, buffering, and mixed-signal systems that require multiple low-power gain stages. Because the MCP604 is unity-gain stable, it can be configured as a voltage follower without external frequency-compensation components, although stable operation at higher closed-loop gains still depends on the selected feedback network and load.
Typical applications include battery-powered sensor conditioning, 4-20 mA receiver stages, portable measurement systems, audio preamplification, active filtering, and low-voltage control loops. The 14-SOIC package is also convenient for prototypes and hand-assembled industrial or instrumentation equipment because it exposes each channel's input, output, and supply pins.
The principal design consideration is supply headroom. The output can approach the supply limits, but large-signal operation and capacitive loading require conservative output-voltage and current margins. Place bypass capacitors close to the supply pins and keep sensitive input and feedback traces away from switching nodes and high-current return paths to minimize injected noise.
This page combines the MCP604-E/SL electrical characteristics with package guidance, application-specific engineering advice, and a comparison of pin-compatible Microchip alternatives. It helps engineers distinguish electrical-temperature variants from true cross-manufacturer replacements before modifying a 14-SOIC PCB.
جێگرەوەکانی جێگۆڕکێ بۆ MCP604-E/SL — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCP604-E/SL (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Typical Operating Current, Package, Supply Voltage Range, Gain-Bandwidth Product, Amplifier Type.
MCP604-I/SL
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP604T-E/ST
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP604-E/SL زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Number of Amplifier Circuits | 4 circuits |
| Amplifier Type | General-purpose CMOS operational amplifier |
| Gain-Bandwidth Product | 2.8 MHz typical |
| Slew Rate | 2.3 V/us typical |
| Typical Operating Current | 230 uA |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Rail-to-Rail Input | Yes |
| Rail-to-Rail Output | Yes |
| Unity-Gain Stability | Yes |
| Maximum Input Voltage | 6.0 V maximum supply referenced |
| پاکێج | 14-SOIC, 3.90 mm body width |
| جۆری دامەزراندن | Surface mount |
| Shipping Format | Tube |
ڕێکخستنی پینی MCP604-E/SL
| پین 1 | OUTA — Amplifier A output |
| پین 2 | INA- — Amplifier A inverting input |
| پین 3 | INA+ — Amplifier A non-inverting input |
| پین 4 | V+ — Positive supply connection |
| پین 5 | INB+ — Amplifier B non-inverting input |
| پین 6 | INB- — Amplifier B inverting input |
| پین 7 | OUTB — Amplifier B output |
| پین 8 | OUTC — Amplifier C output |
| پین 9 | INC- — Amplifier C inverting input |
| پین 10 | INC+ — Amplifier C non-inverting input |
| پین 11 | V- — Negative supply connection |
| پین 12 | IND+ — Amplifier D non-inverting input |
| پین 13 | IND- — Amplifier D inverting input |
| پین 14 | OUTD — Amplifier D output |
بەکارهێنانە باوەکان
MCP604-E/SL گونجاوە بۆ 6 بەکارھێنانs: Battery-Powered Sensor Conditioning, Industrial 4-20 mA Receiver, Audio Preamplification, Active Analog Filtering, Portable Measurement Instrumentation, Low-Voltage Control Loops.
Battery-Powered Sensor Conditioning
The MCP604-E/SL fits low-power sensor interfaces because its 2.7 V minimum supply and 230 uA typical operating current suit portable systems with limited energy budgets. The 2.8 MHz gain-bandwidth product is appropriate for sensors producing relatively slow electrical signals, while four channels can amplify, filter, or buffer multiple measurements. Rail-to-rail input and output behavior helps retain signal range near the supply limits. In a typical sensor board, each channel could provide gain or buffering before an ADC input, provided the design includes suitable bypass capacitance and keeps high-impedance traces short.
پێشنیارکراو
Industrial 4-20 mA Receiver
The MCP604-E/SL is suitable for buffering and signal conditioning in a 4-20 mA industrial receiver when the required bandwidth is moderate. Its rail-to-rail input capability supports operation near the low end of a 2.7 V to 5.5 V supply, while the 2.3 V/us slew rate can reproduce small, filtered current-loop signals without requiring a high-speed amplifier. Four channels allow simultaneous conditioning, filtering, or test-point buffering, although protection components must handle the external industrial transient environment before the signal reaches an op amp input.
پێشنیارکراو
Audio Preamplification
The MCP604-E/SL can implement a compact low-noise preamplifier for microphone, line-level, or headphone-driver input stages operating from a low-voltage supply. The 2.8 MHz gain-bandwidth product supports audio-band amplification, and rail-to-rail output swing increases usable signal range at 2.7 V or 3.3 V. Four channels permit stereo or multichannel routing in one package. The principal tradeoff is that the MCP604 is intended for general-purpose CMOS amplification rather than a specialized ultra-low-noise audio device, so source impedance, gain, bandwidth, and output loading require practical evaluation.
پێشنیارکراو
Active Analog Filtering
The MCP604-E/SL is useful for active low-pass, high-pass, and notch-filter stages where a 2.8 MHz gain-bandwidth product provides more bandwidth than the target signal requires. Its unity-gain stability simplifies follower-based buffer stages, while four channels allow cascading two second-order sections within one package. Component tolerances and the amplifier's open-loop gain response will influence filter accuracy. Keep feedback components close to the relevant amplifier pins and verify stability with the intended source resistance, load capacitance, and supply condition.
پێشنیارکراو
Portable Measurement Instrumentation
The MCP604-E/SL supports portable measurement instruments that combine sensor inputs, excitation control, and signal conditioning on a low-power PCB. Its four independent channels can condition different sensor ranges or provide buffering around multiplexed measurement paths, while the 14-SOIC package simplifies breadboard and through-hole prototype assembly. The 230 uA typical operating current helps control battery drain, but total system power depends on sensor current, display circuitry, and conversion devices. A 2.7 V to 5.5 V operating range also supports common single-supply rails.
پێشنیارکراو
Low-Voltage Control Loops
The MCP604-E/SL can serve as the error amplifier in low-voltage control, current-feedback, or actuator-control loops. The 2.8 MHz gain-bandwidth product offers useful loop bandwidth for slow-to-moderate control loops, while the 2.3 V/us slew rate helps the output follow changing control commands. Four channels allow parallel control, monitoring, and diagnostic functions. Compensation must be designed around the actual loop gain and load, and the rail-to-rail output should not be interpreted as unlimited current capability. Verify output current and stability limits in the manufacturer datasheet before finalizing the compensation network.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MCP604-E/SL — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MCP604-I/SL | MCP604T-E/ST |
|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Number of Amplifier Circuits | 4 circuits | 4 circuits | 4 circuits |
| Gain-Bandwidth Product | 2.8 MHz typical | 2.8 MHz typical | 2.8 MHz typical |
| Minimum Supply Voltage | 2.7 V | 2.7 V | 2.7 V |
| Rail-to-Rail Input | Yes | Yes | Yes |
| Rail-to-Rail Output | Yes | Yes | Yes |
| Unity-Gain Stability | Yes | Yes | Yes |
| Temperature Grade | E grade | I grade | T-grade E variant |
جیاکەرەوە سەرەکییەکان
- Four independent amplifiers in one 14-SOIC package (بەراورد بەMCP604-I/SL)
- Low operating current with practical signal bandwidth (بەراورد بەMCP604-I/SL)
- Rail-to-rail operation on a 2.7 V minimum supply (بەراورد بەMCP604T-E/ST)
تێبینییەکانی دیزاین
Place the positive and negative bypass capacitors close to the MCP604-E/SL supply pins. Keep the ground return path short and connect it directly to the device ground pin rather than routing supply current through the analog input network. High-impedance inputs, such as sensor or feedback nodes, should remain away from switching nodes and digital return paths to reduce parasitic coupling.
Do not treat rail-to-rail operation as an unlimited output-current or unlimited output-voltage capability. Confirm the output-current limit and output-voltage headroom in the manufacturer datasheet for the selected supply, load, and temperature. Use resistor isolation when driving capacitive loads, and verify stable operation with the actual source impedance because the MCP604 is unity-gain stable rather than unconditionally stable in every feedback configuration.
Keep each channel's input, feedback resistor, and compensation components in a compact group. Avoid sharing narrow input traces between amplifier channels and avoid routing feedback routes underneath digital or switching circuitry. For low-noise sensor signals, use short guarded traces, a quiet ground reference, and decoupling placed at the amplifier rather than relying on remote bulk capacitance.
زانیاری پابەندبوون
Compliance attributes are not stated in the referenced manufacturer and distributor records. Confirm the current declarations for the exact MCP604-E/SL orderable configuration with Microchip Technology.