MCP6282-E/P - 5MHz Dual RRIO Op Amp | Microchip
MPN: MCP6282-E/P ✓ چالاکMCP6282-E/P گشتی
An operational amplifier, commonly called an op amp, is an analog signal-conditioning semiconductor that uses high open-loop gain to amplify voltage differences. In the signal-chain hierarchy, the MCP6282-E/P belongs to the operational-amplifier class, within analog amplifiers and integrated circuits. Rail-to-rail input allows the input common-mode voltage to approach either supply rail, while rail-to-rail output allows the output swing to approach the available supply limits under suitable load conditions.
The MCP6282 family provides a 5 MHz gain-bandwidth product and a 65° phase margin. A typical supply current of 450 µA supports low-power signal conditioning, while operation down to 1.8 V permits use with low-voltage systems. The device also provides an extended-temperature option reaching +125°C. Its low-offset voltage, low-bias-current characteristics, and rail-to-rail operation make it useful for sensor interfaces, current sensing, filtering, and general-purpose analog processing.
The dual MCP6282-E/P combines two amplifiers in an 8-pin PDIP package, simplifying analog boards where two gain stages are required. Its 5 MHz bandwidth is suitable for higher-frequency instrumentation than a conventional low-frequency precision amplifier, while the 65° phase margin supports stable closed-loop operation in common non-inverting and inverting configurations. Input and output capability near the supply rails can reduce the need for additional headroom in low-voltage designs.
Typical applications include portable sensor conditioning, low-voltage instrumentation, active filtering, audio and communications interface circuits, and current measurement. The dual format is particularly useful for differential sensing, closed-loop control, or two-stage signal chains. Designers should still evaluate output swing, load current, noise, stability, and common-mode limits against the specific operating conditions.
For a new PCB, place the decoupling capacitor close to the supply pins and route both amplifier channels symmetrically. For an existing design, MCP6282-E/P requires an 8-pin PDIP footprint with the same dual-amplifier pin arrangement; alternative package or function variants cannot be treated as direct drop-in replacements without schematic and footprint verification.
This page combines the manufacturer family information, ordering details for the exact MCP6282-E/P designation, compatibility constraints, application guidance, and practical design considerations to support component selection and board-level implementation.
جێگرەوەکانی جێگۆڕکێ بۆ MCP6282-E/P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCP6282-E/P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Mounting Type, Phase Margin, Typical Supply Current.
هیچ جێگرەوەی ڕاستەوخۆ بۆ ئەم بەرهەمە بەردەست نییە.
داوای جێگرەوەکان بکەMCP6282-E/P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 5 MHz typical |
| Phase Margin | 65° |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Typical Supply Current | 450 µA per amplifier |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Input Offset Voltage | 150 µV typical |
| پلەی گەرمیی کارکردن | Up to +125°C |
| پاکێج | 8-pin PDIP |
| جۆری دامەزراندن | Through-hole |
| Automotive Qualification | Automotive application variant indicated |
ڕێنمایی ڕێکخستنی پینی MCP6282-E/P 8-pin pdip
ڕێکخستنی پین بۆ MCP6282-E/P (پاکێجی 8-pin pdip). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MCP6282-E/P.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MCP6282-E/P گونجاوە بۆ 6 بەکارھێنانs: Low-Voltage Sensor Signal Conditioning, Portable Measurement and Monitoring, Active Filtering and Audio Conditioning, Current Sensing and Feedback Control, Industrial Interface Circuit, Communications and Instrumentation Front End.
Low-Voltage Sensor Signal Conditioning
The MCP6282-E/P fits sensor interfaces because it operates from 1.8 V to 5.5 V and accepts input and output signals approaching the supply rails. A typical circuit can amplify a bridge, resistive sensor, or low-level detector signal in a non-inverting or differential configuration. Its 5 MHz gain-bandwidth product provides more bandwidth than a basic precision op amp, while the 65° phase margin supports stable closed-loop operation. The dual package also allows one channel to condition the sensor and the other to buffer a reference or output signal.
پێشنیارکراو
Portable Measurement and Monitoring
The MCP6282-E/P is appropriate for portable measurement systems that require two analog channels but must limit supply current. Its typical current consumption is 450 µA per amplifier, while operation from 1.8 V supports low-energy sensor nodes and handheld instruments. Rail-to-rail input improves utilization of the available measurement range, and rail-to-rail output helps drive subsequent converter stages. Board designers should still budget input-noise, offset, bias-current, and settling-time margins when resolving very small signals.
پێشنیارکراو
Active Filtering and Audio Conditioning
The MCP6282-E/P can implement active filters and small-signal audio conditioning stages where a 5 MHz typical gain-bandwidth product is appropriate. Two channels in one 8-pin PDIP allow a cascade, band-pass section, or dual signal path without using two separate packages. The 65° phase margin is useful when assessing closed-loop stability, and the low typical supply current supports compact analog boards. Filter design should verify actual gain, noise, slew behavior, output loading, and component tolerances at the intended operating frequency.
پێشنیارکراو
Current Sensing and Feedback Control
The MCP6282-E/P suits low-side or high-side current-sense and closed-loop feedback circuits that benefit from rail-to-rail operation. One channel can amplify a shunt voltage while the second can provide gain, filtering, or an error-amplifier function. Its 5 MHz bandwidth allows faster feedback loops than a conventional low-frequency error amplifier, while the dual package simplifies routing between sensing and control blocks. The final design must check common-mode limits, output swing, offset, noise, and phase margin over the complete current range.
پێشنیارکراو
Industrial Interface Circuit
The MCP6282-E/P can support industrial interface and control boards requiring two general-purpose analog channels in a through-hole package. Rail-to-rail input and output improve compatibility with low-voltage sensor and logic levels, while the 5 MHz bandwidth is useful for moderate-frequency instrumentation. The -E/P temperature option reaches +125°C, supporting designs across extended commercial and industrial temperature ranges. Qualification and application requirements should still be reviewed for each finished equipment category.
پێشنیارکراو
Communications and Instrumentation Front End
The MCP6282-E/P is suitable for communications and test-instrument front ends that require amplification and buffering within a low-voltage signal chain. The 5 MHz gain-bandwidth product provides useful bandwidth for moderate-frequency signals, and rail-to-rail operation reduces the headroom required at low supply voltages. Two channels can process complementary or sequential signals without separate dual packages. Designers should assess noise density, input capacitance, settling time, output drive, and stability against the source impedance and required measurement bandwidth.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MCP6282-E/P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە |
|---|---|
| Package | 8-pin PDIP |
| Brand | Microchip Technology |
| Amplifier Configuration | Dual |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 5 MHz typical |
| Phase Margin | 65° |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Typical Supply Current | 450 µA per amplifier |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
جیاکەرەوە سەرەکییەکان
- Combines two amplifiers in an 8-pin PDIP package (بەراورد بەMCP6281)
- Provides 5 MHz gain-bandwidth product with 65° phase margin (بەراورد بەMCP6283)
- Supports low-voltage rail-to-rail operation (بەراورد بەMCP6284)
تێبینییەکانی دیزاین
Place the supply-decoupling capacitor immediately between the positive supply and ground pins, with a short return path. If the two amplifier channels are used for related signals, route their input and output paths symmetrically to minimize channel-to-channel timing and noise differences. For sensitive high-impedance sources, keep copper and test-probe connections away from the input pins, and verify that source impedance does not degrade the intended stability and noise performance.
Do not treat every MCP6282 package or ordering suffix as a drop-in replacement for MCP6282-E/P. The -E/P ordering code identifies an 8-pin PDIP package, while other identified family configurations use surface-mount packages. A replacement must match the footprint, pin assignment, dual-amplifier channel arrangement, supply range, input/output common-mode behavior, and required output drive before PCB or schematic substitution is approved.
Choose feedback resistors and capacitors for the intended closed-loop bandwidth rather than assuming the 5 MHz gain-bandwidth product is directly usable as the signal bandwidth. Confirm noise gain, phase margin, output loading, and capacitive stability at the selected gain. With high-value resistors, bias-current effects can increase output offset, and with high-capacitance loads or long PCB traces, additional stability analysis may be necessary.
زانیاری پابەندبوون
The available product information identifies an automotive application variant, but it does not provide an explicit AEC-Q100 qualification statement for MCP6282-E/P. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation.