NE5534ADG - Low-Noise 10MHz Op Amp | onsemi | Audio
MPN: NE5534ADG ✓ چالاکNE5534ADG گشتی
An operational amplifier is an analog integrated circuit that uses high-gain differential amplification with negative feedback to create stable signal-processing functions. The NE5534 family combines a bipolar input stage with internal frequency compensation, placing it in the general-purpose operational-amplifier hierarchy. This makes the device useful for audio preamplification, active filtering, buffer amplification, and low-frequency instrumentation while remaining distinct from CMOS rail-to-rail amplifiers designed for very-low-voltage or micropower systems.
The principal strengths are low input noise, a 10 MHz gain-bandwidth product, and 13 V/us slew rate. The bandwidth supports accurate amplification of audio-band and other moderate-frequency signals, while the slew rate helps preserve large-signal fidelity in filters, mixers, and control paths. The NE5534 family also offers improved output-drive capability compared with common TL08x-class amplifiers, making it a practical choice when the output must drive a moderately demanding load.
According to the onsemi datasheet, the amplifier is internally compensated for stable operation at gain values of one or higher and is specified as a single general-purpose amplifier. The device operates from 3 V to 20 V, allowing its use in conventional single-supply and dual-supply analog systems. The 8-SOIC package measures approximately 0.154 inch, or 3.90 mm, in body width and supports conventional surface-mount assembly.
Typical applications include audio mixer input stages, low-noise voltage buffers, active low-pass and band-pass filters, servo-control loops, and instrumentation signal conditioning. In an audio preamplifier, the amplifier can provide channel gain while its low-noise characteristic helps preserve the signal floor. In an active filter, the 10 MHz gain-bandwidth product and 13 V/us slew rate provide useful headroom beyond the audible range, while compensation and feedback stability determine the usable filter bandwidth.
Designers should use the manufacturer datasheet pin-description table when assigning tracks and should preserve the specified compensation and supply arrangements. Input and output layout should minimize parasitic capacitance, maintain short feedback paths, and decouple the supply pins close to the device. Stable operation also depends on correct feedback polarity and suitable output-load conditions; compensation pins must not be treated as general-purpose signal inputs.
This product page combines the exact NE5534ADG identity, package information, electrical characteristics, verified sourcing links, and engineering guidance with a practical comparison of documented equivalents. It is intended to help engineers identify the correct low-noise single amplifier, confirm footprint compatibility, and plan the surrounding filter, decoupling, and signal-conditioning circuitry.
جێگرەوەکانی جێگۆڕکێ بۆ NE5534ADG — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ NE5534ADG (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Slew Rate, Common-Mode Rejection Ratio, Amplifier Type, Supply Voltage Range.
NE5534ADR2G
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →NE5534DG
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →NE5534DR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →NE5534ADG زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | Single low-noise operational amplifier |
| Number of Amplifiers | 1 circuit |
| Supply Voltage Range | 3 V to 20 V |
| Gain-Bandwidth Product | 10 MHz |
| Slew Rate | 13 V/us |
| Amplifier Type | General purpose |
| پاکێج | 8-SOIC, 0.154 inch (3.90 mm) width |
| جۆری دامەزراندن | Surface mount |
| Packaging | Tube |
ڕێکخستنی پینی NE5534ADG
| پین 1 | OFFSET NULL — Offset-voltage null adjustment |
| پین 2 | COMPENSATION — External compensation connection |
| پین 3 | IN- — Inverting input |
| پین 4 | IN+ — Non-inverting input |
| پین 5 | COMPENSATION — External compensation connection |
| پین 6 | OUT — Amplifier output |
| پین 7 | V+ — Positive supply input |
| پین 8 | NC — Not connected |
بەکارهێنانە باوەکان
NE5534ADG گونجاوە بۆ 6 بەکارھێنانs: Low-Noise Audio Preamplifier, Active Audio Filter, Instrumentation Signal Conditioning, Servo and Control Loop, Mixer and Summing Amplifier, Audio Distribution Buffer.
Low-Noise Audio Preamplifier
The NE5534ADG fits a low-noise audio preamplifier because it combines low-noise operation with a 10 MHz gain-bandwidth product and 13 V/us slew rate. It can amplify a source signal before a mixer, volume-control stage, or line-level output while preserving small-signal detail. The single-amplifier package also avoids allocating a second active channel when the board requires only one audio path. Stable operation depends on selecting the correct feedback network, observing the compensation-pin arrangement, and placing the device where grounding and supply return currents do not pass through sensitive input nodes.
پێشنیارکراو
Active Audio Filter
The NE5534ADG is appropriate for an active low-pass, high-pass, or band-pass filter when the closed-loop bandwidth remains comfortably below its 10 MHz gain-bandwidth product. Its 13 V/us slew rate also provides useful large-signal capability when filter components generate appreciable output transitions. The amplifier is internally compensated for a minimum closed-loop gain of one, so the resistor and capacitor network must preserve stable feedback operation. Place feedback components close to the device and use short ground returns to prevent added noise and phase shift.
پێشنیارکراو
Instrumentation Signal Conditioning
The NE5534ADG can serve as a buffer or gain stage for instrumentation signals because its 3 V to 20 V supply range supports conventional analog supplies and its 10 MHz gain-bandwidth product handles signals well above many sensor bandwidths. The low-noise architecture is useful when the amplifier must not add substantial noise to a weak measurement. At higher closed-loop gains, verify the exact bandwidth, input-noise, and compensation arrangement in the onsemi datasheet. Use a clean analog ground and provide local supply bypassing to prevent coupling from adjacent digital circuitry.
پێشنیارکراو
Servo and Control Loop
The NE5534ADG is suitable for a general-purpose control loop that requires more bandwidth and output drive than a basic precision amplifier. Its 10 MHz gain-bandwidth product supports loop dynamics beyond the audio range, while 13 V/us slew rate can improve response to fast control errors. The amplifier is normally used with negative feedback, making loop stability, compensation, and output loading essential design checks. Keep the forward and feedback paths short, place the compensation network according to the manufacturer guidance, and avoid routing high-current return paths through the reference-ground connection.
پێشنیارکراو
Mixer and Summing Amplifier
The NE5534ADG can implement a low-noise summing or mixer channel when multiple source signals are combined through carefully selected feedback networks. Its 13 V/us slew rate provides greater large-signal capability than slower general-purpose amplifiers, while the 10 MHz gain-bandwidth product leaves bandwidth margin above typical audio frequencies. Feedback resistors should be arranged to preserve stable operation, and each summed input should be isolated as required to prevent interaction between sources. The single-package format is useful when each mixer board channel requires one dedicated amplifier.
پێشنیارکراو
Audio Distribution Buffer
The NE5534ADG works as a unity-gain audio buffer when the source must drive a longer cable, a mixer input, or another stage without additional attenuation. The internal compensation supports a minimum closed-loop gain of one, and the amplifier's 10 MHz gain-bandwidth product provides more than enough bandwidth for conventional audio signals. Output-drive capability is stronger than that of several common TL08x-type amplifiers, making the device useful for moderately demanding analog loads. Confirm output-current and swing limits from the datasheet, and isolate the buffer from high-current return paths.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ NE5534ADG — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | NE5534ADR2G | NE5534DG | NE5534DR |
|---|---|---|---|---|
| Package | 8-SOIC (0.154 inch, 3.90 mm width) | 8-SOIC (0.154 inch, 3.90 mm width) - same | 8-SOIC (0.154 inch, 3.90 mm width) - same | 8-SOIC (0.154 inch, 3.90 mm width) - same |
| Brand | onsemi | onsemi | onsemi | Texas Instruments |
| Number of Amplifiers | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 10 MHz | 10 MHz | 10 MHz | 10 MHz |
| Slew Rate | 13 V/us | 13 V/us | 13 V/us | 13 V/us |
جیاکەرەوە سەرەکییەکان
- A-grade low-noise family selection (بەراورد بەNE5534DG)
- Identical core bandwidth and slew performance (بەراورد بەNE5534ADR2G)
- Drop-in footprint continuity for NE5534-family boards (بەراورد بەNE5534DR)
تێبینییەکانی دیزاین
Route the non-inverting input directly to the source, and place feedback resistors close to pins 3, 4, and 6 to minimize parasitic capacitance. Keep input nodes away from supply pins, compensation pins, and switching nodes. A compact ground return for the amplifier is preferable to routing input return current through a noisy analog-ground region. The datasheet pin table should be used directly when assigning PCB tracks.
Do not treat compensation pins as ordinary inputs or outputs. Their configuration depends on the amplifier's stability requirements and operating gain, so removing or adding components without consulting the manufacturer guidance can cause oscillation. Likewise, do not assume that unity-gain operation alone eliminates all stability checks; verify source capacitance, load impedance, feedback topology, and any external compensation required for the final board.
Place the supply-decoupling capacitor close to the positive supply pin and provide a low-impedance return path to the supply ground. For audio and instrumentation boards, separate sensitive input routing from power converters, relay drivers, and high-current outputs. Keep the footprint compatible with the 8-SOIC body dimensions and verify pin orientation, solder-paste land pattern, and tube-versus-reel handling requirements before release to production.
زانیاری پابەندبوون
No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact NE5534ADG ordering code. AEC-Q100 is not applicable because NE5534ADG is a general-purpose commercial operational amplifier rather than an automotive-qualified variant.