Texas Instruments

OPA134UA - 8MHz FET Audio Op Amp | Texas Instruments

MPN: OPA134UA ✓ چالاک
±18 V Vdss 50 pA Id 8-SOIC, 0.154 inch (3.90 mm) width Package
MOQ: 1 |

OPA134UA گشتی

Texas Instruments OPA134UA is a single, high-performance SoundPlus audio operational amplifier with an 8 MHz gain-bandwidth product, true FET input stage, 20 V/us slew rate, 8 nV/Hz noise density, and an 8-pin SOIC package. According to the Texas Instruments product page, the OPA134 is specified for low-distortion audio applications and combines a 50 pA input bias current with a wide ±18 V supply range.

An operational amplifier is an analog signal-conditioning semiconductor that compares two input voltages and drives its output to amplify the difference between them. The OPA134 belongs to the SoundPlus high-performance audio operational-amplifier family, where low noise, low distortion, wide bandwidth, and high output drive are more important than the very low cost or minimal power of general-purpose precision amplifiers.

The OPA134UA uses a true FET-input architecture, with the manufacturer listing input bias current at 50 pA and noise density at 8 nV/Hz. Its 8 MHz gain-bandwidth product supports wide-band signal paths, while the 20 V/us slew rate improves large-signal behavior. The family is fully specified for audio applications and is available in single, dual, and quad configurations. The UA ordering code places this single amplifier in an 8-pin SOIC package.

The OPA134 series is designed for audio equipment where low distortion is critical to signal quality. The manufacturer identifies 0.00008% ultra-low distortion as a family feature. A true FET input stage supports low-bias operation, while the combination of wide bandwidth, high slew rate, and strong DC performance is intended to preserve signal fidelity across demanding audio paths.

Typical uses include high-end audio preamplifiers, line-level stages, active crossover networks, headphone-driver signal chains, mixer blocks, and instrumentation requiring low-noise voltage amplification. Its wide ±18 V power-supply capability makes it suitable for professional and consumer audio systems that operate from conventional dual-supply rails. Headphone-buffer designs should still verify output-current and load requirements for the selected external circuit.

For PCB implementation, place the bypass capacitors close to the supply pins and preserve the package pin arrangement defined in the manufacturer datasheet. Because no complete OPA134UA pin table appears in the product-page snippets, use the pin-description diagram in the manufacturer documentation before assigning amplifier inputs, output, and supply connections.

This product record combines the manufacturer's defining electrical characteristics, package information, practical application guidance, and a focused comparison with related operational amplifiers. It also distinguishes verified drop-in candidates from options that require footprint and electrical review before substitution.

جێگرەوەکانی جێگۆڕکێ بۆ OPA134UA — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ OPA134UA (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Package, Slew Rate, Input Bias Current, Gain-Bandwidth Product.

Texas Instruments
Amplifier Type: Single, General Purpose, FET-Input Operational Amplifier
Package: 8-pin SOIC (D), surface mount
Slew Rate: 2 V/us
بەراوردکردن لەگەڵ OPA134UA →
Texas Instruments
Amplifier Type: Single operational amplifier
Package: 8-pin SOIC
Slew Rate: 20 V/µs
بەراوردکردن لەگەڵ OPA134UA →
Texas Instruments
Amplifier Type: Single FET-input operational amplifier
Package: 8-SOIC, 0.154 in (3.90 mm) width
Slew Rate: 3.5 V/µs
بەراوردکردن لەگەڵ OPA134UA →

OPA132UA

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-SOIC
Single operational amplifier · 5 pA nominal · 50 pA · 8 MHz · 20 V/µs · ±18 V · 130 dB with 600 Ω load · 500 µV

✓ بەردەستە

$3.6094 / یەکە

بینینی داتاشیت →

OPA137UA

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-SOIC
Single FET-input operational amplifier · 1 channel · 36 V · 1 MHz · Rail-to-rail to the positive supply · ±10 pA · 5 pA · 120 µA per channel

پەیوەندی بۆ نرخ

بینینی داتاشیت →

OPA130UA

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 8-SOIC
Single, General Purpose, FET-Input Operational Amplifier · 1 · 1 MHz · 2 V/us · 20 pA typical · 530 uA typical · +/-2.25 V to +/-18 V · 8-pin SOIC (D), surface mount

پەیوەندی بۆ نرخ

بینینی داتاشیت →

OPA134UA زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Amplifier Type Single audio operational amplifier
Number of Circuits 1 circuit
Technology True FET input
Gain-Bandwidth Product 8 MHz
Slew Rate 20 V/us
Input Bias Current 50 pA
چڕیی دەنگ 8 nV/Hz
Total Harmonic Distortion 0.00008%
Open-Loop Gain 600
Supply Voltage Range ±18 V
پاکێج 8-SOIC, 0.154 inch (3.90 mm) width
جۆری دامەزراندن Surface mount
Product Family OPAx134 SoundPlus audio operational amplifiers

ڕێنمایی ڕێکخستنی پینی OPA134UA 8-soic, 0.154 inch (3.90 mm) width

ڕێکخستنی پین بۆ OPA134UA (پاکێجی 8-soic, 0.154 inch (3.90 mm) width). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.

نەخشەی پینئاوتی پاکێجی 8-soic, 0.154 inch (3.90 mm) width بۆ OPA134UA

هیچ داتای وردی پینئاوت بەردەست نییە بۆ OPA134UA.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

OPA134UA گونجاوە بۆ 6 بەکارھێنانs: High-End Audio Preamplifier, Headphone Driver Signal Chain, Active Crossover Network, Line-Level Audio Mixer, Professional Audio Interface, Precision Test and Measurement Amplifier.

🎧

High-End Audio Preamplifier

The OPA134UA fits a low-noise voltage-gain stage in a high-end audio preamplifier because the Texas Instruments device combines 8 nV/Hz noise density, 50 pA input bias current, and 0.00008% distortion. Place it in a stable non-inverting or inverting topology selected for the required gain, with feedback components chosen against the amplifier’s stability data. Its 8 MHz gain-bandwidth product and 20 V/us slew rate preserve both small-signal detail and larger transients. Compared with a general-purpose amplifier selected mainly for input impedance, this part gives the designer explicit audio-oriented noise and distortion targets.

🎧

Headphone Driver Signal Chain

OPA134UA can serve in the voltage-amplification section ahead of a discrete headphone output stage when the design needs low-noise amplification with fast transient response. The 20 V/us slew rate helps reproduce attack and decay edges, while the 8 nV/Hz noise density limits added broadband noise in a quiet listening path. Its true FET input stage and 50 pA bias current are useful with high-impedance sources. Output-current capability, load impedance, thermal margin, and stability must be verified for the exact headphone topology because those requirements are not established by the headline frequency and slew-rate figures.

💡

Active Crossover Network

The OPA134UA is appropriate for active crossover sections that process multiple audio bands and require low distortion across the passband. Its 8 MHz gain-bandwidth product provides headroom above the crossover frequencies, and the 20 V/us slew rate supports accurate large-signal transitions in the filtered signal. The 50 pA input bias current reduces disturbance from high-impedance source networks. Each filter section should be checked for closed-loop stability, noise-gain versus crossover frequency, component tolerances, and maximum output level to ensure the wide-band device remains stable throughout the passband and stopband transition.

🔧

Line-Level Audio Mixer

OPA134UA can amplify and sum low-level line signals in a mixer where low distortion and low noise are central to preserving program material. The 0.00008% distortion specification and 8 nV/Hz noise density support accurate handling of quiet passages, while the 8 MHz bandwidth provides ample audio-band margin. Use resistor-based summing networks with appropriate values and verify that the feedback network remains stable at every practical gain setting. Headroom and output-drive requirements should be calculated from the maximum number of simultaneously active inputs rather than inferred solely from the amplifier’s bandwidth.

🎙️

Professional Audio Interface

OPA134UA is suitable for a professional audio interface’s analog input conditioning when low-noise gain and low distortion are required ahead of conversion. Its true FET input stage, 50 pA input bias current, and 8 nV/Hz noise density support source-connected instrumentation, while ±18 V supply capability supports conventional split-rail analog circuits. The 8 MHz gain-bandwidth product allows useful bandwidth margin above the audio band. Designers should still check input common-mode range, output swing, slew behavior into the converter’s sample-and-hold input, and stability with source capacitance before finalizing the stage.

🔧

Precision Test and Measurement Amplifier

OPA134UA can serve as a low-noise, wide-band voltage amplifier in test and measurement equipment when the signal path benefits from its 8 nV/Hz noise density, 20 V/us slew rate, and low 0.00008% distortion. The 8 MHz closed-loop capability permits measurement bandwidth well above the audible range when the chosen noise gain allows it. A true FET input stage with 50 pA bias current can suit high-impedance sensors. The source impedance, input capacitance, grounding method, resistor accuracy, and required settling time must be evaluated because low noise alone does not guarantee accurate transient measurements.

What are the key specifications of OPA134UA that engineers should know?
The OPA134UA is a single true-FET-input audio operational amplifier with an 8 MHz gain-bandwidth product, 20 V/us slew rate, 50 pA input bias current, 8 nV/Hz noise density, and an 8-pin SOIC package. According to the Texas Instruments OPA134 product page, the device is intended specifically for high-performance audio. Its amplifier family also specifies ultra-low distortion of 0.00008%, high open-loop gain of 600, and operation from dual supplies up to ±18 V. These characteristics make it more appropriate for demanding audio signal paths than a basic low-cost amplifier selected only for closed-loop gain and supply voltage.
Where can I download the OPA134UA datasheet PDF?
The OPA134UA datasheet PDF is available from Texas Instruments through the manufacturer document link at https://www.ti.com/lit/ds/symlink/opa2134.pdf. The linked document covers the OPA134, OPA2134, and OPA4134 SoundPlus audio operational-amplifier family and describes the true FET input stage, audio performance, ordering information, and application details. The OPA134UA product page at https://www.ti.com/product/OPA134 provides the official product landing page, parameter filters, quality information, and links for selecting the precise UA ordering option.
Where can I find the OPA134UA pinout?
The OPA134UA pinout is found in the pin-configuration and pin-description tables in the Texas Instruments OPAx134 family datasheet. The UA package is an 8-pin SOIC, but the product-page snippets do not reproduce the numbered signal assignments. Use the manufacturer datasheet rather than a generic SOIC drawing because the offset null, supply, input, output, and feedback connections must be assigned exactly as specified for OPA134. Place the bypass capacitors near the supply pins after confirming their pin numbers from that diagram.
Is OPA134UA suitable for high-end audio preamplifiers?
The OPA134UA is suitable for high-end audio preamplifiers because its family combines a true FET input stage, 8 nV/Hz noise density, 0.00008% distortion, 8 MHz bandwidth, and 20 V/us slew rate. The Texas Instruments manufacturer description identifies OPA134 as a high-performance audio amplifier with FET inputs. In a low-gain voltage-amplification stage, these characteristics preserve small musical signals and reproduce larger transients with low added distortion. The final design should still be checked for closed-loop stability, output loading, supply headroom, and the required input/output impedance.
What can replace OPA134UA in the same circuit?
OPA132UA is the clearest same-brand replacement candidate identified for the OPA134UA because it is an 8-pin SOIC device in the related TI single-op-amplifier family. Other related parts require closer review because their key ratings may differ. According to the manufacturer’s family organization, the OPA134 series emphasizes 8 MHz bandwidth, 20 V/us slew rate, 50 pA bias current, 8 nV/Hz noise, and 0.00008% distortion. Confirm the candidate’s supply range, output drive, stability, and exact pin mapping in its datasheet before accepting it as a drop-in substitution.
Is OPA134UA the same as OPA132UA?
No. OPA134UA and OPA132UA are related Texas Instruments single operational amplifiers in 8-pin SOIC packages, but they are not specified as identical parts. OPA134UA is the SoundPlus high-performance audio device associated with 8 MHz bandwidth, 20 V/us slew rate, 50 pA input bias current, and 8 nV/Hz noise density. OPA132UA may provide a practical footprint-compatible alternative, yet its own electrical ratings and stability requirements govern the substitution. Review both datasheets and verify every pin and critical specification before updating the BOM.
What is the best Analog Devices equivalent for OPA134UA?
No specific Analog Devices equivalent can be confirmed as a drop-in replacement from the available cross-reference information. A defensible selection requires an 8-pin SOIC footprint, compatible input and output pin assignments, suitable supply voltage, adequate output drive, acceptable noise and distortion, and stable operation at the intended closed-loop gain. The cross-reference source identifies Analog Devices among manufacturers represented in OPA134 comparisons, but it does not expose a verified part number with all required match details. Request a component-level comparison from XAIPART and verify the proposed replacement against both manufacturers’ datasheets.
OPA134UA vs OPA137UA - which is better for audio?
OPA134UA is generally the more directly specified choice when the design calls for the Texas Instruments SoundPlus audio position: 8 MHz bandwidth, 20 V/us slew rate, 50 pA input bias current, 8 nV/Hz noise density, and 0.00008% distortion. OPA137UA is a related device but must be judged against the OPA134 on power, noise, distortion, output drive, and package pinout. The comparison evidence does not establish that OPA137UA is universally drop-in equivalent. Use OPA134UA when its published audio ratings align with the design, and evaluate OPA137UA only after checking its exact datasheet.
OPA134UA vs OPA130UA - which is better for a low-noise audio path?
OPA134UA is the clearer choice when the design prioritizes the manufacturer-defined SoundPlus audio performance of 8 MHz bandwidth, 20 V/us slew rate, 50 pA input bias current, 8 nV/Hz noise density, and 0.00008% distortion. OPA130UA is a related TI operational amplifier whose noise, speed, supply, and distortion ratings must be reviewed independently. The available comparison page does not establish identical electrical performance or a guaranteed drop-in relationship. Choose OPA134UA when its published ratings match the target gain, bandwidth, load, and distortion budget; otherwise compare OPA130UA against the full design requirements.
When should I choose OPA134UA over OPA132UA?
Choose OPA134UA when the audio design benefits from its published 8 MHz gain-bandwidth product, 20 V/us slew rate, 50 pA input bias current, 8 nV/Hz noise density, and 0.00008% distortion. Consider OPA132UA when its verified ratings meet the same signal-chain requirements and it offers a better fit for supply, output-load, or sourcing constraints. Both are associated with 8-pin SOIC single-amplifier options, but package similarity alone does not establish identical behavior. Validate closed-loop stability, output swing, and every pin connection before making a production substitution.
Is OPA134UA suitable for active crossover and mixer circuits?
The OPA134UA is suitable for active crossover and mixer circuits when the stage operates inside its specified bandwidth, slew rate, output-load, and supply limits. Its 8 MHz gain-bandwidth product supports audio-frequency filtering stages, while 20 V/us slew rate preserves large-signal edges. The 50 pA FET-input bias current and 8 nV/Hz noise density are favorable for high-impedance source paths. Use the manufacturer application information to select the feedback network and ensure the chosen noise-gain configuration remains stable with the actual source and load impedances.
How much supply voltage does OPA134UA require?
OPA134UA supports a wide supply range extending to ±18 V, as identified in the family feature description. Actual operating limits must still be checked in the manufacturer datasheet for the specific ordering code and temperature grade. A ±18 V capability means the amplifier can operate from split 18 V rails, subject to the total supply and common-mode restrictions applicable to the device. Provide local decoupling close to the supply pins and verify output voltage swing before operating near either rail.
Where can I buy OPA134UA online?
Use the Request a Quote form on this page to request OPA134UA availability, current lead time, minimum order quantity, and the exact UA packaging configuration. The Texas Instruments product page is also appropriate for confirming device identity and quality information. Commercial terms can change, so a current quotation is preferable to a static listing. The requested part should be confirmed as OPA134UA in an 8-SOIC package rather than the dual OPA2134 or quad OPA4134 family members.
What is the price of OPA134UA?
The current price of OPA134UA depends on quantity, package suffix, market conditions, and required availability. Use the Request a Quote form on this page to obtain a current quotation for the exact OPA134UA ordering code and requested quantities. The price is rendered from structured commercial data where a qualifying quantity-break listing is available, while quote-based fulfillment can also be arranged. Confirm that the quoted line item is the 8-SOIC UA version before releasing a purchase order.
What is the lead time for OPA134UA?
The current lead time for OPA134UA should be requested through the Request a Quote form on this page, with the required quantity and delivery destination stated. Lead time can vary with order quantity, inventory, and the exact UA package and reel configuration. The manufacturer product page can confirm the device’s supported ordering options and quality status. For production planning, request a committed lead time rather than relying on a historical distributor stock statement, because inventory levels change rapidly.
Is OPA134UA in stock?
Current OPA134UA stock status should be confirmed through the Request a Quote form on this page. Some distributor search pages display historical or changing inventory messages, but those notices do not guarantee allocation for a specific order. Include the required quantity, package suffix, reel orientation, and target delivery date in the request. The Texas Instruments product page remains the authoritative source for product identity and ordering information, while XAIPART can confirm commercial availability for the requested configuration.

داتای سەرچاوەی ئەندازیاری بۆ OPA134UA — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose OPA134UA when a single-amplifier, 8-SOIC audio stage needs the manufacturer’s explicit combination of 8 MHz bandwidth, 20 V/us slew rate, 50 pA input bias current, 8 nV/Hz noise density, and 0.00008% distortion. Consider OPA132UA when its complete electrical ratings satisfy the circuit and its sourcing or functional fit is preferable, but confirm the exact pin and performance differences before substitution. OPA137UA is relevant when its distinct electrical profile better serves the target gain, bandwidth, or power requirements, and OPA130UA is similarly useful when its verified characteristics improve the design. The shared 8-SOIC format simplifies mechanical comparison, yet production use still requires pin-level, stability, loading, supply, noise, and distortion review.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە OPA132UA OPA137UA OPA130UA
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Amplifier Configuration Single Single Single Single

جیاکەرەوە سەرەکییەکان

  • Manufacturer-defined ultra-low audio distortion (بەراورد بەOPA132UA)
  • Fast 20 V/us slew rate for large-signal audio (بەراورد بەOPA137UA)
  • True FET input with 50 pA bias current (بەراورد بەOPA130UA)

تێبینییەکانی دیزاین

Confirm the exact OPA134UA pin assignments in the Texas Instruments family datasheet before routing the board. Place the supply-bypass capacitors close to the device's positive and negative supply pins, with short, low-loop-area traces and a solid ground reference. Keep sensitive audio input traces away from switching nodes and high-current output paths. Because the available product snippets do not show the complete pin table, do not infer SOIC pinout from another amplifier or another member of the OPAx134 family.

Design each feedback network for the intended closed-loop gain and source impedance. The OPA134UA has an 8 MHz gain-bandwidth product, so higher closed-loop gains leave less bandwidth for stability and signal shaping. Check capacitive loading at the output and source capacitance at the input against the manufacturer guidance. For active filters or crossover networks, calculate noise gain across the passband and transition region rather than evaluating stability only at the nominal midband gain.

Do not treat a shared SOIC footprint as proof of an interchangeable amplifier. Before replacing OPA134UA with OPA132UA, OPA137UA, or OPA130UA, compare pin functions, input common-mode range, output swing, output-current capability, supply limits, noise, distortion, slew rate, and stability at the actual closed-loop gain. The 20 V/us slew rate and ±18 V supply capability describe OPA134UA; a substitute must be checked independently rather than inheriting those ratings.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The verified product information identifies OPA134UA as a Texas Instruments audio operational amplifier but does not state the requested compliance attributes.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

opa134ua datasheet OPA134UA pinout OPA134UA datasheet pdf OPA134UA specifications OPA134UA SOIC-8 OPA134UA audio amplifier OPA134UA equivalent OPA134UA replacement OPA134UA vs OPA132UA OPA134UA vs OPA137UA Texas Instruments OPA134UA OPA134UA price OPA134UA stock OPA134UA 8MHz FET op amp

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments OPA134UA OPA134 OPA132UA OPA137UA OPA130UA Operational amplifier Audio operational amplifier SoundPlus True FET input JFET Gain-bandwidth product Slew rate Noise density Input bias current Total harmonic distortion Open-loop gain 8-SOIC SOIC family Surface mount Audio preamplifier Active crossover Headphone amplifier Line-level mixer Professional audio interface
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ