Texas Instruments

OPA234UA - Low-Power Precision Op Amp | Texas Instruments

MPN: OPA234UA ✓ چالاک
Up to 36 V Vdss 250 µA per amplifier Id 8-pin SOIC Package
MOQ: 1 |

OPA234UA گشتی

Texas Instruments OPA234UA is a low-power, precision, single-supply operational amplifier with 350 kHz gain-bandwidth product, 0.2 V/µs slew rate, and 250 µA quiescent current per amplifier, packaged in an 8-pin SOIC. It operates from a single supply as high as 36 V or from dual supplies up to ±18 V, with guaranteed performance identified at 2.7 V, 5 V, and ±15 V.

An operational amplifier is an analog signal-conditioning integrated circuit that uses high open-loop gain to amplify small voltage differences. In the broader electronics hierarchy, the OPA234UA belongs to the linear amplifier, operational amplifier, and analog integrated-circuit categories. Its low-power architecture makes it especially useful in battery-powered instrumentation, portable measurement systems, industrial sensors, and low-voltage signal-conditioning circuits where both supply-voltage range and current consumption matter.

The OPA234 series combines low offset voltage, high common-mode rejection ratio, and high power-supply rejection ratio. Its input common-mode range can extend below ground in single-supply operation, while the output can swing to within 50 mV of ground. These characteristics support direct sensing of low-level signals referenced to ground without a separate negative supply. The combination of 350 kHz bandwidth and 0.2 V/µs slew rate also provides useful response speed for precision DC and low-frequency AC signal paths.

OPA234UA is intended for low-voltage, low-power applications and can operate from either single or dual power supplies. Single-supply operation extends to 36 V, while dual operation reaches ±18 V. The low 250 µA-per-amplifier quiescent current reduces supply demand in portable systems, although input bias current, offset voltage, noise, and load-capacitance limits must still be checked against the application’s precision and stability requirements.

Typical uses include low-level sensor conditioning, portable instrumentation, buffered analog measurements, and precision current-voltage signal chains. The device is particularly appropriate when the source signal is close to ground and a negative supply would otherwise be required. It is also suitable for industrial systems that need a wide supply range, although input and output common-mode limits must be respected at each supply voltage.

When designing a circuit around the OPA234UA, place input and output decoupling capacitors close to their corresponding supply pins and keep feedback components compact to minimize parasitic capacitance and instability. Check the datasheet’s common-mode, output-swing, and capacitive-load limits before operating near a supply rail. Avoid assuming that the rail-to-rail input capability permits arbitrary source voltages outside the specified common-mode range.

This product data combines supply-range, bandwidth, slew-rate, packaging, and cross-reference information with application guidance, comparison parameters, and practical design considerations. It helps engineers evaluate whether the OPA234UA fits a low-power precision signal path and identify a pin-compatible replacement without overlooking the electrical limits of the SOIC-8 footprint.

جێگرەوەکانی جێگۆڕکێ بۆ OPA234UA — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

OPA234UAG4

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin SOIC
0% principal rated-performance difference; terminals, functional characteristics, and package are described as consistent

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

OPA234UA زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Number of Amplifiers 1 amplifier
Product Type Low-power precision operational amplifier
Single-Supply Voltage Range Up to 36 V
Dual-Supply Voltage Range ±18 V
Guaranteed Supply Configurations 2.7 V, 5 V, and ±15 V
ئێستای ئارام 250 µA per amplifier
Gain-Bandwidth Product 350 kHz
Slew Rate 0.2 V/µs
Single-Supply Common-Mode Range Extends below ground
Minimum Output Swing to Ground 50 mV
پاکێج 8-pin SOIC
جۆری دامەزراندن Surface mount

ڕێکخستنی پینی OPA234UA

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 NC — Unused amplifier-channel pin; connection must follow the manufacturer datasheet
پین 2 NC — Unused amplifier-channel pin; connection must follow the manufacturer datasheet
پین 3 NC — Unused amplifier-channel pin; connection must follow the manufacturer datasheet
پین 4 V- — Negative supply connection
پین 5 NC — Unused amplifier-channel pin; connection must follow the manufacturer datasheet
پین 6 NC — Unused amplifier-channel pin; connection must follow the manufacturer datasheet
پین 7 NC — Unused amplifier-channel pin; connection must follow the manufacturer datasheet
پین 8 V+ — Positive supply connection

بەکارهێنانە باوەکان

OPA234UA گونجاوە بۆ 6 بەکارھێنانs: Portable Sensor Signal Conditioning, Battery-Powered Measurement, Industrial Process Monitoring, Low-Voltage Audio and Control Signals, Precision Current-to-Voltage Conversion, Precision Data-Acquisition Front End.

🧩

Portable Sensor Signal Conditioning

The OPA234UA fits portable sensor-conditioning circuits because its single-supply operation extends to 36 V, its input common-mode range extends below ground, and its quiescent current is 250 µA per amplifier. It can amplify a sensor output close to 0 V without adding a negative supply rail, helping reduce board complexity. The 350 kHz gain-bandwidth product and 0.2 V/µs slew rate are sufficient for many pressure, temperature, and position sensors operating at low or moderate frequencies. Confirm the actual sensor output range against the amplifier’s common-mode limits, and verify settling requirements at the selected closed-loop gain before finalizing the filter network.

📱

Battery-Powered Measurement

OPA234UA is appropriate for battery-powered measurement equipment where amplifier power consumption affects operating time. Its 250 µA-per-amplifier quiescent current is low enough to support compact portable instruments, while operation from 2.7 V single supply covers common low-energy systems. The device can process signals near ground because its single-supply input common-mode range extends below ground. Designers should include the output load, feedback network, and protection leakage in the complete power budget, and confirm that output settling remains adequate for the measurement bandwidth before choosing the final gain and compensation values.

🏭

Industrial Process Monitoring

The OPA234UA can be used in industrial process-monitoring front ends that need a wide supply range and precision DC performance. A single 36 V supply provides useful input headroom, while ±18 V dual operation supports legacy instrumentation. The low offset voltage, high common-mode rejection ratio, and high power-supply rejection ratio described by the manufacturer help preserve measurement accuracy near supply-distribution noise. However, compliance details and the exact operating-temperature range must be confirmed for the installation environment. The complete front end should also include input filtering, surge protection, and a defined grounding strategy.

🎧

Low-Voltage Audio and Control Signals

OPA234UA can amplify low-level control or audio-related signals in compact single-supply systems. Its 350 kHz gain-bandwidth product and 0.2 V/µs slew rate are adequate for many low-frequency audio and control paths, while the output can approach ground to within 50 mV. This makes it useful where the signal is centered near the lower supply rail and a bipolar output would be inconvenient. For higher-bandwidth audio or capacitive loads, verify the required frequency response, output swing, and stability margin rather than assuming general-purpose performance is sufficient.

⚡

Precision Current-to-Voltage Conversion

OPA234UA is well suited to precision transimpedance and current-to-voltage conversion when the source current is low frequency and the output must operate from a single supply. The input common-mode range extending below ground allows feedback arrangements referenced to ground, and the low 250 µA quiescent current helps preserve measurement-system efficiency. Feedback-resistor noise and input-bias current can dominate accuracy at very small currents, so use stable resistors and verify temperature coefficients. The 350 kHz bandwidth also limits how quickly the loop can respond to transients, making the complete sensor bandwidth a key design criterion.

📺

Precision Data-Acquisition Front End

OPA234UA can serve as the analog amplifier ahead of a data-acquisition converter in a precision measurement chain. Its low offset voltage, high common-mode rejection ratio, and high power-supply rejection ratio help reduce systematic errors, while operation from 2.7 V, 5 V, or ±15 V supports multiple instrument architectures. The 350 kHz gain-bandwidth product should be compared with the required closed-loop bandwidth and settling time, not merely with the converter’s sample rate. Input antialiasing, common-mode-range checks, and layout measures that minimize parasitic pickup remain necessary for accurate acquisition results.

What is the operating voltage of OPA234UA?
The OPA234UA operates from a single supply up to 36 V or from dual supplies up to ±18 V. According to the manufacturer datasheet, guaranteed performance is specified at 2.7 V, 5 V, and ±15 V. This wide range allows the same precision amplifier to support low-voltage portable systems and higher-voltage industrial instrumentation. Check the common-mode and output-swing limits at the actual supply voltage before finalizing the signal path.
What are the key specifications of OPA234UA that engineers should know?
The OPA234UA combines a 350 kHz gain-bandwidth product, 0.2 V/µs slew rate, and 250 µA quiescent current per amplifier in an 8-pin SOIC package. According to the manufacturer datasheet, the device operates from a single supply up to 36 V or from dual supplies up to ±18 V. Its single-supply input common-mode range extends below ground, and the output can swing to within 50 mV of ground.
Is OPA234UA suitable for single-supply applications?
Yes, the OPA234UA is specifically designed for low-voltage, low-power, single-supply operation. According to the manufacturer datasheet, the single-supply range extends to 36 V, while performance is guaranteed at 2.7 V and 5 V. The input common-mode range extends below ground, allowing signals near ground to be processed without a negative supply. Output swing and input limits must still be checked at the selected rail voltage.
Where can I download the OPA234UA datasheet PDF?
The OPA234UA datasheet PDF is available through the manufacturer datasheet link on this page and through the listed technical-document sources. The document describes the OPA234, OPA2234, and OPA4234 family, including supply ranges, electrical characteristics, pin assignments, and application guidance. Use the pin-description table and electrical characteristic tables when assigning tracks and checking the OPA234UA operating limits.
Where can I find the OPA234UA pinout?
The OPA234UA pinout is shown in the manufacturer datasheet and uses an 8-pin SOIC footprint. The pin-description table should be used for final board routing because unused amplifier-channel pins must be left in their specified conditions. The package drawing also identifies the physical pin-1 orientation. Verify the land pattern against the chosen SOIC-8 manufacturer footprint rather than relying only on a schematic symbol.
What can replace OPA234UA?
OPA234UAG4 is a documented pin-to-pin replacement candidate for OPA234UA. Its terminals, package, and principal performance characteristics are described as consistent with OPA234UA, making it suitable for footprint-level substitution after checking current availability and temperature-grade requirements. Only this replacement was explicitly identified in the cross-reference information; additional alternatives should not be treated as drop-in without confirming the complete pinout and electrical characteristics.
Is OPA234UA the same as OPA234UAG4?
OPA234UAG4 is identified as a direct replacement for OPA234UA with consistent terminals, package, and functional characteristics. The 8-pin SOIC package permits the same board footprint, but engineers should still verify lot traceability, operating-temperature requirements, and supply availability for the specific production build. The replacement is best viewed as an electrically and physically compatible option rather than a change to the original circuit function.
OPA234UA vs OPA234UAG4: which is better for an existing design?
OPA234UAG4 is the stronger choice for an existing OPA234UA design when equivalent pins, terminals, package, and principal performance are required, because it is explicitly identified as a complete replacement. OPA234UA remains appropriate when a particular approved source or lifecycle arrangement is needed. For either choice, verify the latest ordering information, temperature range, and production qualification before releasing the design.
When should I choose OPA234UA over a higher-speed amplifier?
Choose OPA234UA when the signal path needs precision rather than high bandwidth and the design benefits from a 250 µA quiescent-current amplifier. Its 350 kHz gain-bandwidth product and 0.2 V/µs slew rate are appropriate for low-frequency measurement and sensor-conditioning circuits. Choose a faster amplifier only when the required closed-loop bandwidth, slew rate, or capacitive-load capability exceeds those limits.
Is OPA234UA suitable for low-level sensor signals?
The OPA234UA is suitable for many low-level sensor signals because its input common-mode range extends below ground in single-supply operation. This supports sensors whose outputs are close to 0 V without requiring a negative rail. According to the manufacturer datasheet, the device also provides low offset voltage, high common-mode rejection, and high power-supply rejection, helping reduce errors from sensor mismatch and supply ripple.
What is the quiescent current of OPA234UA?
The OPA234UA has a quiescent current of 250 µA per amplifier. According to the manufacturer datasheet, the OPA234 series was designed to reduce supply demand compared with older precision operational-amplifier families. Actual board consumption also depends on the output state, feedback network, load current, and any attached compensation network, so quiescent current should not be treated as the only contributor to total power.
Where to buy OPA234UA online?
Use the Request a Quote form on this page to request OPA234UA availability, lot information, and a current quotation. The form provides a direct purchasing route without relying on stale listings or third-party seller claims. When requesting a quote, include the required quantity, package marking, date code tolerance, and any special handling or traceability requirements that apply to the finished assembly.
What is the price of OPA234UA?
Use the Request a Quote form on this page for the current OPA234UA quotation. Commercial terms can change with quantity, inventory, package markings, and sourcing conditions, so the Request a Quote response should be treated as the purchasing reference. Include your required quantity and delivery expectations so the quotation reflects the actual production need.
What is the lead time for OPA234UA?
The current lead time for OPA234UA should be requested through the Request a Quote form on this page. Lead time can depend on order quantity, package choice, date-code requirements, and current factory availability. Provide the production quantity, requested delivery date, and whether assembly traceability is required when submitting the request.
Is OPA234UA in stock?
Current OPA234UA stock status should be confirmed through the Request a Quote form on this page. Inventory can change quickly, and a listing does not guarantee allocation for production quantities. State the required quantity, package marking, acceptable date-code range, and target delivery date so the response can reflect a meaningful supply commitment.
What is the best cross-brand equivalent for OPA234UA?
No cross-brand drop-in equivalent can be confirmed from the identified OPA234 replacement information. According to the cross-reference results, the available entry is a Texas Instruments part rather than a cross-brand device. A foreign-manufacturer amplifier should be selected only after its 8-pin SOIC pinout, supply range, common-mode behavior, offset voltage, noise, bias current, output drive, and stability requirements are verified against the OPA234UA design.

داتای سەرچاوەی ئەندازیاری بۆ OPA234UA — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose OPA234UA when designing a low-power precision signal path that operates from a single supply as high as 36 V, especially when the source signal is near ground. Its 250 µA quiescent current, 350 kHz gain-bandwidth product, and 0.2 V/µs slew rate make it appropriate for sensor conditioning, portable measurement, current-to-voltage conversion, and precision data-acquisition front ends. OPA234UAG4 is the documented drop-in option when equivalent terminals, performance, and the 8-pin SOIC footprint are required. Do not select either part without checking the required signal bandwidth, output swing, input common-mode range, and capacitive loading. A faster amplifier is preferable when settling time or slew-rate requirements exceed the OPA234UA’s capability, while a lower-power device may be better when supply current dominates the design.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە OPA234UAG4
Brand Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC - same package
Number of Amplifiers 1 amplifier 1 amplifier
Single-Supply Maximum 36 V 36 V
Dual-Supply Maximum ±18 V ±18 V
Quiescent Current 250 µA per amplifier 250 µA per amplifier
Gain-Bandwidth Product 350 kHz 350 kHz
Slew Rate 0.2 V/µs 0.2 V/µs
Output Swing to Ground Within 50 mV of ground Within 50 mV of ground
Special Features Single-supply common-mode range extends below ground Same principal characteristics and terminal arrangement

جیاکەرەوە سەرەکییەکان

  • Pin-compatible replacement with no principal performance change (بەراورد بەOPA234UAG4)
  • Wide single-supply operating range (بەراورد بەOPA234UAG4)
  • Low quiescent current with useful signal bandwidth (بەراورد بەOPA234UAG4)

تێبینییەکانی دیزاین

Use the manufacturer pin-description table when assigning the eight SOIC pins, especially the unused amplifier-channel pins. Place supply-bypass capacitors close to pins 4 and 8 and keep the feedback loop compact. A short, narrow input route and a stable ground-return path help prevent parasitic capacitance and common-mode pickup from degrading the 350 kHz gain-bandwidth capability.

Estimated: at a 5 V single supply, 250 µA quiescent current and a 100 kΩ load to ground produce approximately 5 V × (250 µA + 50 µA) = 1.5 mW of estimated amplifier power, excluding output-current variation and external-network current. These inputs illustrate why OPA234UA is attractive for portable designs. Confirm total system consumption using the actual load, feedback network, and operating state.

Do not assume that an input can be driven beyond the common-mode range even though it can operate from a single supply and accept signals below ground. Likewise, the output reaching within 50 mV of ground does not guarantee a zero-volt output. Review the manufacturer’s input-range and output-swing graphs for the selected supply voltage, load, and temperature before setting signal or feedback limits.

Keep input and feedback components close to the SOIC pins and avoid long parallel routes around the amplifier. For low-level measurements, use a single grounded reference point and shield or guard sensitive input traces where appropriate. The 350 kHz closed-loop bandwidth and 0.2 V/µs slew rate limit large-signal performance, so verify the required signal amplitude and frequency rather than relying on small-signal bandwidth alone.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

No explicit OPA234UA compliance declarations were identified in the manufacturer or distributor information. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status from current manufacturer documentation before qualification.

داتا پشتڕاستکراوەتەوە لە: 2026-11-19 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

OPA234UA datasheet OPA234UA pinout OPA234UA datasheet pdf OPA234UA specifications OPA234UA operating voltage OPA234UA quiescent current OPA234UA 8-SOIC pinout OPA234UA single supply amplifier OPA234UA sensor signal conditioning OPA234UA equivalent OPA234UA replacement OPA234UA vs OPA234UAG4 OPA234UA price OPA234UA stock Texas Instruments OPA234UA

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments OPA234UA OPA234UAG4 OPA234 series operational amplifier precision amplifier low-power amplifier single-supply amplifier dual-supply amplifier analog integrated circuit linear amplifier gain-bandwidth product slew rate quiescent current common-mode rejection ratio power-supply rejection ratio input offset voltage input bias current common-mode range 8-pin SOIC SOIC package family surface-mount package portable instrumentation sensor signal conditioning precision data acquisition
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ