OPA552UA - 380mA, 60V, 12MHz Operational Amplifier | TI
MPN: OPA552UA ✓ چالاکOPA552UA گشتی
An operational amplifier is an active analog signal-processing component that uses differential feedback to amplify the voltage difference between its non-inverting and inverting inputs. The OPA552 belongs to the operational-amplifier hierarchy within analog and power-management semiconductors. Its combination of wide supply-voltage range, high output-current capability, and wide bandwidth allows it to drive loads that are beyond the practical limits of many conventional precision amplifiers.
The principal features of the OPA552 include 380 mA typical output current, operation across a 60 V supply range, 12 MHz gain-bandwidth performance, and a slew rate of 24 V/µs. These characteristics make it appropriate for amplifier stages requiring both signal bandwidth and substantial load-driving capability. The device is also available in SOIC-8, PDIP-8, and higher-current power-package options within the OPA55x family.
OPA551 and OPA552 devices use laser-trimmed monolithic integrated circuits and are specified over the extended industrial temperature range from -40 °C to +125 °C. The OPA552 is positioned as the faster, higher-current member of the related OPA551 and OPA552 comparison. A feedback-network design using gains of 5 or greater helps preserve bandwidth and stability in applications that need to drive low-impedance or current-sensitive loads.
Typical uses include telephone-interface amplification, audio output stages, servo and motor-control loops, waveform-generation circuits, laboratory instrumentation, and power-supply feedback networks. In each case, the amplifier combines a wide common-mode operating range with the ability to source or sink considerably more current than a conventional small-signal operational amplifier.
The principal design trade-off is thermal dissipation. At high supply voltage and sustained output current, power converted into heat can become substantial, so PCB copper area, enclosure temperature, and nearby heat sources require attention. Decoupling capacitors should be placed close to the supply pins, and the feedback components should use values consistent with the intended gain and bandwidth.
This product page combines manufacturer specifications, a same-package OPA551UA alternative, application guidance, and parameter-level comparison information to support faster component evaluation and board-level sourcing decisions.
جێگرەوەکانی جێگۆڕکێ بۆ OPA552UA — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ OPA552UA (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Amplifier Type, Gain-Bandwidth Product, Package, Slew Rate.
OPA551UA/2K5
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →OPA552UA زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Amplifier Type | Single operational amplifier |
| Maximum Supply Voltage | 60 V |
| Typical Output Current | 380 mA |
| Gain-Bandwidth Product | 12 MHz |
| Slew Rate | 24 V/µs |
| Optimized Minimum Gain | 5 |
| مەودای پلەی گەرمیی کارکردن | -40 °C to +125 °C |
| پاکێج | 8-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Output Offset Voltage | 3000 µV maximum |
ڕێنمایی ڕێکخستنی پینی OPA552UA 8-pin soic
ڕێکخستنی پین بۆ OPA552UA (پاکێجی 8-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ OPA552UA.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
OPA552UA گونجاوە بۆ 6 بەکارھێنانs: Telephony Signal Amplification, Audio Output Amplification, Servo and Motor-Control Loops, Laboratory Test and Measurement, Waveform and Pulse Generation, Power-Supply Feedback Networks.
Telephony Signal Amplification
OPA552UA fits telephone-interface circuits that require amplification from a comparatively high-voltage signal environment. Its 60 V supply capability provides operating headroom for line-connected stages, while 380 mA typical output current offers more drive than a standard small-signal operational amplifier. The 12 MHz gain-bandwidth product supports wider-band voice or control signals when the feedback network is designed for gains of 5 or greater. Because line-interface boards may be exposed to sustained signal levels, evaluate output swing and thermal dissipation at the worst load rather than relying only on the typical output-current rating.
پێشنیارکراو
Audio Output Amplification
OPA552UA can serve as an audio output or line-drive stage where the load demands substantially more current than a conventional precision amplifier. Its 380 mA typical output current, 12 MHz gain-bandwidth product, and 24 V/µs slew rate provide a useful combination for low-impedance audio paths, while the 60 V high-voltage class allows operation from elevated bipolar supply rails. The main design issue is power dissipation: high rail voltage and sustained current rapidly increase junction temperature. Use a feedback network appropriate for the intended gain, and verify clipping, output swing, crossover behavior, and enclosure temperature.
پێشنیارکراو
Servo and Motor-Control Loops
OPA552UA is suitable for servo-control and motor-drive feedback networks that need both high supply-voltage tolerance and stronger output drive than ordinary precision amplifiers provide. The 380 mA typical output current can support lower-impedance control signals, while the 60 V capability accommodates elevated actuator or supply rails. Its 12 MHz bandwidth and 24 V/µs slew rate help preserve loop response when gain is set to 5 or greater. Designers must still account for output saturation, feedback compensation, noise sensitivity, and the substantial heat that can be generated across a large supply-to-output voltage difference.
پێشنیارکراو
Laboratory Test and Measurement
OPA552UA is well suited to laboratory test equipment that must condition signals across a wide voltage range and drive moderately low-impedance inputs. The 60 V operating capability supports high-amplitude test signals, while 380 mA typical output current gives the amplifier more authority than conventional precision op amps. Its 12 MHz gain-bandwidth product is useful for moderate-bandwidth instrumentation and waveform circuits, particularly when the design targets gains of 5 or greater. For accurate measurement results, check input and output ranges, distortion, settling behavior, and thermal drift rather than assuming that high output drive alone ensures precision.
پێشنیارکراو
Waveform and Pulse Generation
OPA552UA can generate and shape moderate-frequency waveforms where the load requires substantial current and the output must operate from a high-voltage supply. Its 12 MHz gain-bandwidth product and 24 V/µs slew rate provide useful large-signal performance, while 380 mA typical output current helps maintain waveform control into lower-impedance loads. The manufacturer recommends optimization for gains of 5 or greater, making the device appropriate for non-inverting amplifier and gain blocks in test systems. Watch output-current limits, slew-limited accuracy, thermal rise, and output saturation when selecting the load and feedback values.
پێشنیارکراو
Power-Supply Feedback Networks
OPA552UA can be used in high-voltage power-supply feedback or error-amplifier circuits because it combines a 60 V supply class with substantial output-current capability. The 380 mA typical drive allows the amplifier to influence a control node through a more demanding feedback network than a conventional precision op amp, while the 12 MHz bandwidth can respond quickly to loop corrections. Designers should optimize gain for stability, place compensation components close to the amplifier, and account for the power dissipated when the output operates far from the supply rails. Thermal analysis is especially important in high-line industrial systems.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ OPA552UA — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | OPA551UA |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC |
| Maximum Supply Voltage | 60 V | 60 V |
| Typical Output Current | 380 mA | 200 mA |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C |
| Number of Circuits | 1 circuit | 1 circuit |
جیاکەرەوە سەرەکییەکان
- Higher typical output-current capability (بەراورد بەOPA551UA)
- Faster large-signal performance (بەراورد بەOPA551UA)
- Same-package family alternative available (بەراورد بەOPA551UA)
تێبینییەکانی دیزاین
Estimated: use P = (VIN - VOUT) × IOUT to estimate amplifier dissipation before applying the package thermal limits from the manufacturer datasheet. For example, 30 V across the output device with 100 mA load produces about 3 W. Verify that PCB copper, ambient temperature, and adjacent heat sources keep the junction below its rated limit; otherwise reduce the voltage difference, load, or duty cycle.
Place the supply-bypass capacitors directly between the positive and negative supply pins and the corresponding ground reference, using the shortest possible traces. Keep the feedback-resistor network close to the inverting input to minimize parasitic capacitance and feedback-loop length. For an 8-pin SOIC, verify every pin function against the official pin-description table before laying out tracks.
Do not assume that the 380 mA typical output-current rating permits continuous operation at every supported voltage. Check output swing, short-circuit behavior, power dissipation, and thermal limits at the actual load. Also avoid treating the 60 V capability as permission to exceed the device's absolute-maximum limits; include startup transients and fault conditions in the design review.
زانیاری پابەندبوون
The available manufacturer product information does not state a component-level RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration. The OPA55x family is described as an industrial-temperature operational amplifier, not an AEC-Q100-qualified automotive device.