Texas Instruments

PCA9534RGVR - 8-Bit I2C I/O Expander | Texas Instruments

MPN: PCA9534RGVR ✓ چالاک
2.3 V to 5.5 V Vdss 16 pins Package 400 kHz Speed
MOQ: 1 |

PCA9534RGVR گشتی

The Texas Instruments PCA9534RGVR is an 8-bit I2C/SMBus low-power I/O expander supporting a 2.3 V to 5.5 V supply range, 400 kHz bus operation, and remote general-purpose I/O expansion in a 16-pin VQFN package measuring 4 x 4 mm. It provides eight configurable ports, one interrupt output, and three hardware address inputs. The PCA9534RGVR is designed to add eight GPIOs to a host microcontroller without consuming eight direct I/O pins.

An I/O expander is an interface IC that extends the number of digital input/output lines available to a controller. The PCA9534 belongs to the broader hierarchy of I2C interface controllers, SMBus peripherals, GPIO expanders, and interface ICs. It communicates with a host through the two-wire SDA and SCL bus, while the eight port pins can be configured individually as inputs or outputs through internal registers.

Key device features include three address pins, A0, A1, and A2, which allow up to eight PCA9534 devices to share one I2C or SMBus bus. The interrupt output provides a change-detection path to the host, while configuration registers support input, output, and quasi-bidirectional operating modes. According to the manufacturer product page, the device operates from 2.3 V to 5.5 V and is compatible with 400 kHz I2C signaling.

The PCA9534 uses a host-controlled serial interface rather than dedicating a microcontroller port to each external signal. Address selection is established by the A0, A1, and A2 pins, and the controller accesses configuration, input, output, and interrupt-related registers through the bus. This architecture makes the device suitable for systems whose fixed controller pin count is insufficient for relays, sensors, LEDs, keys, or other digital peripherals.

Typical uses include industrial control panels, battery-powered instruments, automated test equipment, and embedded systems with multiple digital loads. It can also provide bus-managed GPIO nodes in communications equipment, measurement systems, and compact controller boards. The device is particularly useful when the required expansion is eight lines rather than a large, high-speed parallel interface.

Designers should treat SDA and SCL as bus signals requiring suitable pull-up resistors and careful board layout. Account for address-pin strapping, power-supply decoupling, and the electrical characteristics of every attached peripheral. Although the PCA9534 is pin-to-pin and I2C-address compatible with the PCF8574, the manufacturer states that software changes are required because of the PCA9534 register enhancements.

This page combines manufacturer specifications, sourcing guidance, package details, application engineering notes, and a strict same-package replacement comparison. It is designed to help engineers determine whether the PCA9534RGVR fits a voltage range, bus topology, interrupt architecture, and PCB footprint without relying on a basic distributor listing alone.

جێگرەوەکانی جێگۆڕکێ بۆ PCA9534RGVR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ PCA9534RGVR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە I2C Bus Frequency, Package Dimensions.

Texas Instruments
I2C Bus Frequency: 100 kHz
Package Dimensions: 3 mm x 3 mm
بەراوردکردن لەگەڵ PCA9534RGVR →

PCA9534RGVRG4

✅ جێگرەوەی ڕاستەوخۆ
📦 16-pin VQFN (4 x 4 mm)
Same PCA9534 function, pinout, 2.3 V to 5.5 V supply, 8 I/O ports, and 400 kHz bus; qualification and environmental ordering details are 0% different in the identified core interfaces

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

PCA9534RGVR تایبەتمەندییەکان

Number of I/O Ports 8 ports
I/O Port Resolution 8 bits
ڤۆڵتاژی دابینکردنی کارکردن 2.3 V to 5.5 V
I2C Bus Frequency 400 kHz
جۆری ڕووکار I2C and SMBus
Address Configuration Inputs 3 inputs
Devices per Bus Up to 8 devices
Interrupt Outputs 1 output
Configuration Registers Present
Package Pin Count 16 pins
Package Dimensions 4 x 4 mm
Package Type 16-pin VQFN
جۆری دامەزراندن Surface mount
دۆخی RoHS RoHS3 compliant
REACH Status Not specified
Moisture Sensitivity Level MSL 2, 260 C, 1 year

ڕێکخستنی پینی PCA9534RGVR

QFN-16 Package Pinout Diagram QFN-16 3x3mm, P0.5mm, EP 1.7x1.7mm, JEDEC MO-220. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 QFN-16
پین 1 INT — Interrupt output
پین 2 P0 — Bidirectional I/O port 0
پین 3 P1 — Bidirectional I/O port 1
پین 4 P2 — Bidirectional I/O port 2
پین 5 P3 — Bidirectional I/O port 3
پین 6 P4 — Bidirectional I/O port 4
پین 7 P5 — Bidirectional I/O port 5
پین 8 P6 — Bidirectional I/O port 6
پین 9 P7 — Bidirectional I/O port 7
پین 10 A2 — Address input 2
پین 11 A1 — Address input 1
پین 12 A0 — Address input 0
پین 13 SDA — Serial data input/output
پین 14 SCL — Serial clock input
پین 15 VSS — Ground reference
پین 16 VDD — Positive supply voltage

بەکارهێنانە باوەکان

PCA9534RGVR گونجاوە بۆ 6 بەکارھێنانs: Industrial Control Panel I/O Expansion, Battery-Powered Test and Measurement, Communications Equipment Status Inputs, LED and Relay Control Expansion, Embedded Sensor and Key Interface, Compact Automation and Robotics Control.

🏭

Industrial Control Panel I/O Expansion

The PCA9534RGVR is suitable for adding keypad inputs, status indicators, relay-control outputs, and discrete sensor inputs to a compact industrial controller. Its eight ports share one 2-wire interface at up to 400 kHz, while A0, A1, and A2 permit several expanders to occupy distinct addresses on the same bus. The 2.3 V to 5.5 V operating range accommodates common industrial control rails. The interrupt output can notify the controller when an input state changes, avoiding continuous polling. Port setup should be completed through the configuration registers before external loads are enabled, and external pull-ups should be added wherever a port must actively source a defined HIGH level.

🔧

Battery-Powered Test and Measurement

The PCA9534RGVR can expand a low-power measurement controller with eight digital lines for fixture control, limit comparison, and instrument triggering. Operating from 2.3 V to 5.5 V supports systems built around low-voltage supplies, and the I2C interface reduces the number of host-controller pins required. When most ports remain low between measurements, the external pull-up network can dominate standby dissipation, so resistor values and state control should be reviewed. The 400 kHz bus rate is suitable for configuration commands and low-speed status updates rather than continuous high-rate waveform sampling. Firmware should configure ports and masks interrupts before enabling connected peripherals.

🌐

Communications Equipment Status Inputs

The PCA9534RGVR is useful in communications equipment that needs more status, fault, or control lines than the host processor can expose directly. Eight ports can represent module-present, alarm, reset, or peripheral-enable signals while using only SDA, SCL, and an optional interrupt connection. The A0, A1, and A2 inputs allow multiple identification or configuration nodes on a shared bus, helping isolate subsystems on one controller. At the 2.3 V minimum supply voltage, the device fits low-voltage logic domains, although every attached signal must remain within its voltage limits. Firmware should validate pin direction and mask unintended wake events when the interrupt line is connected to a shared controller resource.

💡

LED and Relay Control Expansion

The PCA9534RGVR provides a compact way to control LEDs, relay drivers, and discrete loads when a host controller has limited output pins. The eight ports are grouped logically on a register-addressed device, allowing software to update multiple outputs through the I2C bus and use the interrupt line for monitoring. The 16-pin 4 x 4 mm VQFN saves board area compared with a discrete 8-bit parallel interface. Loads that exceed the port ratings must use suitable transistor or driver circuitry, and inductive loads require appropriate suppression. External port pull-ups should be sized for the required output state and current, while firmware should initialize outputs to a safe inactive condition before enabling attached hardware.

🧩

Embedded Sensor and Key Interface

The PCA9534RGVR can gather digital sensor states, selector switches, and push-button events while preserving controller I/O for higher-bandwidth functions. Its interrupt output supports change-driven handling when the host does not need to poll all eight inputs continuously. Address strapping permits multiple expansion nodes, and the 2.3 V to 5.5 V range covers several common logic systems. Mechanical inputs may bounce, so firmware should use debouncing appropriate to the switch type rather than assuming every interrupt is a valid transition. External pull-ups can maintain defined input states, while the configuration registers should be set for input or output operation before external circuitry is energized.

🏭

Compact Automation and Robotics Control

The PCA9534RGVR is appropriate for distributed digital I/O in compact automation equipment where several nodes must communicate over a shared bus. Eight independently configurable ports can handle discrete actuator commands and equipment interlocks, while A0, A1, and A2 provide straightforward bus addressing. The 400 kHz I2C rate supports typical command and status traffic, and the small 4 x 4 mm VQFN supports compact controller boards. The interrupt output can prompt the controller to inspect changed inputs, reducing unnecessary polling. Designers should account for electrical isolation, actuator transients, grounding, and safe power-up states because the expander is intended for logic-level signaling rather than direct high-power load control.

What is the PCA9534RGVR and what does it do?
The PCA9534RGVR is an 8-bit I2C/SMBus I/O expander that adds eight configurable digital lines to a host controller. It operates from 2.3 V to 5.5 V, supports bus speeds up to 400 kHz, and is packaged in a 16-pin VQFN. According to the Texas Instruments product page, it includes one interrupt output and registers for configuring the ports.
What is the operating voltage of PCA9534RGVR?
The PCA9534RGVR operates from 2.3 V to 5.5 V. This range allows the device to interface with common 3.3 V and 5 V embedded systems. The Texas Instruments product page identifies the device as an 8-bit, 2.3 V to 5.5 V I2C/SMBus I/O expander, making the supply requirements suitable for industrial, consumer, and instrument applications.
Where can I download the PCA9534RGVR datasheet PDF?
The official PCA9534RGVR datasheet PDF is available from the Texas Instruments document link on this page. It describes the 8-bit port architecture, register map, electrical characteristics, address configuration, interrupt behavior, and application information. Use the manufacturer PDF rather than a third-party mirror when establishing the authoritative pinout and operating limits for a new design.
Where can I find the PCA9534RGVR pinout?
The PCA9534RGVR pinout is shown in the manufacturer datasheet under the pin configuration and pin functions tables. The device uses a 16-pin VQFN arrangement, with VDD, ground, SDA, SCL, three address inputs, eight port pins, and an interrupt output. Assign PCB tracks by following the numbered land pattern and exposed-pad requirements in the package drawing.
How many PCA9534 devices can share one I2C bus?
Up to eight PCA9534 devices can share one I2C or SMBus bus. The A0, A1, and A2 hardware inputs select the fixed bus address, allowing eight distinct address combinations. According to the Texas Instruments product page, these three address pins are used to program and vary the I2C address of each device on the shared two-wire bus.
Is PCA9534RGVR pin-compatible with PCF8574?
The PCA9534RGVR is pin-to-pin and I2C-address compatible with the PCF8574, but firmware changes are required. Texas Instruments specifically notes that software must change to accommodate the PCA9534 register enhancements. The cross-reference also references NXP Application Note AN469 for guidance when migrating an existing PCF8574 design.
Can PCA9534RGVR replace PCF8574ADWR in an existing design?
The PCA9534 can replace a PCF8574 electrically and by address, but the host firmware must be revised for the enhanced PCA9534 registers. Texas Instruments states that the devices are pin-to-pin and I2C-address compatible while warning that software changes are required. Verify the original PCB package and port behavior before treating any particular orderable suffix as a drop-in replacement.
What is the best drop-in replacement for PCA9534RGVR?
The closest same-package replacement identified is the Texas Instruments PCA9534RGVRG4, which uses the same 16-pin VQFN footprint and PCA9534 function. A decisive drop-in recommendation still requires confirmation of temperature grade, qualification status, and ordering configuration against the original design. Fewer than five qualified drop-in alternatives were identified, so functionally similar but differently packaged devices are not presented as replacements.
Is PCA9534RGVR the same as NXP PCA9534?
The NXP PCA9534 provides the same fundamental 8-bit I2C/SMBus GPIO-expansion function and is described as pin-to-pin and I2C-address compatible with the PCF8574 series. However, the NXP generic product number does not establish the exact VQFN orderable suffix required for a PCB-level drop-in decision. Confirm the NXP package drawing, pinout, address behavior, and register map before substitution.
When should I choose PCA9534RGVR over a direct MCU GPIO?
Choose the PCA9534RGVR when a controller lacks eight free GPIO pins or when bus-managed expansion simplifies the PCB. It adds eight configurable lines over I2C, supports address sharing, and provides an interrupt path. Direct MCU GPIO is preferable when the application requires very low latency, frequent high-speed toggling, or no shared-bus overhead.
How should I configure PCA9534RGVR pull-ups and address pins?
Configure SDA and SCL pull-ups for the intended bus voltage and loading, and strap A0, A1, and A2 to valid logic levels before the device begins communicating. Texas Instruments specifies three hardware address inputs and up to eight devices per bus. Confirm the address-selection levels and bus capacitance from the manufacturer datasheet so that address collisions and excessive RC loading are avoided.
Does PCA9534RGVR require an external pull-up on each I/O pin?
The PCA9534 is identified as a low-power I/O expander whose configuration differs from devices with internal port pull-up resistors. Applications generally need external pull-ups when the port must source a defined HIGH state, particularly when the output is otherwise left unconnected. Select resistor values from the port sink-current, rise-time, bus-capacitance, and leakage requirements in the manufacturer datasheet.
What is the maximum I2C clock rate of PCA9534RGVR?
The PCA9534RGVR supports I2C operation up to 400 kHz. The verified distributor listing identifies the part as an 8-bit I2C/SMBus expander with 400 kHz signaling, while the manufacturer describes its two-wire bus interface. The actual system bus rate must also satisfy the rise-time and pull-up requirements of the complete bus.
Is PCA9534RGVR suitable for low-power embedded systems?
The PCA9534RGVR is suitable for low-power embedded systems because it provides eight remote digital lines through a two-wire interface and is specified as a low-power I/O expander. Its 2.3 V to 5.5 V operating range also supports common low-voltage rails. Final power budgeting should include the supply current, attached load current, pull-up dissipation, and the duration of any active port states.
What are the key specifications of PCA9534RGVR that engineers should know?
The principal PCA9534RGVR specifications are 8 configurable I/O ports, a 2.3 V to 5.5 V operating range, 400 kHz I2C/SMBus operation, three address inputs, support for up to eight devices per bus, one interrupt output, and a 16-pin 4 x 4 mm VQFN package. These parameters define its electrical, bus, addressing, and PCB constraints in compact systems.

داتای سەرچاوەی ئەندازیاری بۆ PCA9534RGVR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose PCA9534RGVR when a design needs eight configurable digital lines over I2C or SMBus within a 2.3 V to 5.5 V supply range and a 16-pin 4 x 4 mm VQFN footprint. It is especially useful when the host controller lacks spare GPIO and the application can tolerate serial bus access. PCA9534RGVRG4 is the closest same-package alternative because its core interface, port count, voltage range, bus rate, and pinout are identical; review its qualification and ordering details before transferring an existing design. Do not substitute the NXP PCA9534 solely by function. Although the manufacturer describes it as pin-to-pin and I2C-address compatible with the PCF8574 family, the exact NXP package and register differences must be verified. Direct microcontroller GPIO remains preferable for latency-sensitive or continuously toggled signals, while the PCA9534 is strongest for moderate-speed status, control, and change-detection tasks.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە PCA9534RGVRG4
Brand Texas Instruments Texas Instruments
Package 16-pin VQFN (4 x 4 mm) 16-pin VQFN (4 x 4 mm)
I/O Port Count 8 ports 8 ports
Operating Supply Voltage 2.3 V to 5.5 V 2.3 V to 5.5 V
I2C Bus Frequency 400 kHz 400 kHz
Interface I2C and SMBus I2C and SMBus
Address Inputs 3 inputs 3 inputs
Interrupt Output 1 output 1 output
Configuration Registers Present Present

جیاکەرەوە سەرەکییەکان

  • Identical core interface and port capacity (بەراورد بەPCA9534RGVRG4)
  • Direct pin-to-pin PCB reuse (بەراورد بەPCA9534RGVRG4)
  • Eight shared-bus expansion lines (بەراورد بەPCA9534RGVRG4)

تێبینییەکانی دیزاین

Place the device close to the SDA and SCL bus routing and keep the address-strapping traces away from long high-impedance branches. Confirm the exposed-pad connection and land pattern against the 4 x 4 mm VQFN package drawing. Maintain the recommended ground-plane connection, route supply current away from sensitive signal paths, and place the local supply-decoupling capacitor close to VDD and ground pins.

Size SDA and SCL pull-ups from the bus voltage, total capacitance, leakage, and required rise time rather than using one resistor value for every board. An undersized resistor increases low-level sink current, while an oversized resistor can produce slow rising edges and ringing. Confirm that the complete bus, including PCA9534 inputs and other attached devices, remains compatible with 400 kHz operation.

Do not assume that a PCA9534 can replace a PCF8574 without changing firmware. Texas Instruments states that the devices are pin-to-pin and I2C-address compatible, but software changes are required for the PCA9534 register enhancements. Also avoid assuming that a generic PCA9534 orderable number is a PCB-level drop-in replacement until its exact package, suffix, temperature range, and pinout have been verified.

Budget the PCA9534 supply current together with port load current and pull-up dissipation. External port pull-ups can create a continuing path to VDD when a port is held LOW, so resistor values directly affect low-power operation. Select external loads that remain within the electrical limits stated in the manufacturer datasheet and add appropriate buffering for high-current or inductive loads.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The part listing identifies RoHS3 compliance and MSL 2 at 260 C for one year. No manufacturer statement confirming AEC-Q100 qualification, lead-free construction, halogen-free construction, or conflict-minerals compliance was identified.

داتا پشتڕاستکراوەتەوە لە: 2026-11-19 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

PCA9534RGVR datasheet PCA9534RGVR pinout PCA9534RGVR datasheet pdf Texas Instruments PCA9534RGVR PCA9534RGVR equivalent PCA9534RGVR replacement PCA9534RGVR drop-in substitute PCA9534RGVR VQFN-16 footprint PCA9534RGVR I2C address configuration PCA9534RGVR PCF8574 compatibility PCA9534RGVR price PCA9534RGVR stock PCA9534RGVR lead time PCA9534RGVR GPIO expander application PCA9534RGVR vs PCA9534RGVRG4

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments PCA9534RGVR PCA9534RGVRG4 PCA9534 I/O expander GPIO expander I2C SMBus interface IC semiconductor remote 8-bit I/O port SDA SCL interrupt output configuration registers A0 A1 A2 16-pin VQFN QFN family surface mount SMD industrial control test and measurement MSL 2 RoHS
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ