Texas Instruments

PCF8574RGTR - 8-Bit I2C I/O Expander | Texas Instruments

MPN: PCF8574RGTR ✓ چالاک
2.5 V to 5.5 V Vdss 16-pin VQFN (RGT) Package 100 kHz Speed
MOQ: 1 |

PCF8574RGTR گشتی

The Texas Instruments PCF8574RGTR is an 8-bit I2C/SMBus input/output expander with interrupt, operating from 2.5 V to 5.5 V at up to 100 kHz in a 16-pin VQFN (RGT) package measuring 3 mm by 3 mm. It adds eight quasi-bidirectional GPIO lines to a host microcontroller through a two-wire serial bus.

An I/O expander is an interface IC that extends the number of general-purpose input and output pins available to a microcontroller or system-on-chip. The PCF8574 belongs to the parallel I/O expander family within the interface IC hierarchy, connects to a host through I2C, and presents each remote port as a standard logic-level GPIO. Its compact package and interrupt output make it useful when a design lacks sufficient pins for switches, indicators, relays, or control inputs.

Key features include eight configurable I/O ports, operation from 2.5 V to 5.5 V, a 100 kHz I2C interface, three hardware address inputs, and an active-low open-drain interrupt output. The interface is compatible with both I2C and SMBus systems, while the small 3 mm by 3 mm VQFN footprint saves board area in space-constrained control boards. The manufacturer specifies an operating temperature range of -40 °C to +85 °C.

Each port can operate as an input or output and is designed for devices that source or sink modest logic-level current. The quasi-bidirectional architecture includes a weak output driver that can be actively pulled low or released for input detection. This arrangement works well with pull-up-based buses and typical digital peripherals, although firmware must account for the port's input and output drive characteristics when resolving multiple low-level signals.

Typical uses include expanding GPIO on an 8-bit microcontroller, driving LED indicators and key inputs in an industrial control panel, reading switch banks in an appliance, and supporting addressable bus nodes in embedded equipment. The interrupt pin can wake or notify the host when a port changes state, reducing the need for continuous polling when the application allows interrupt-driven I/O handling.

Place pull-up resistors on SDA and SCL according to the bus voltage and capacitance, and route the interrupt trace away from high-current switching nodes. Confirm that connected peripherals remain within the port's voltage, current, and timing limits. The exposed-pad package also requires a proper thermal and electrical ground connection under the device.

This page combines manufacturer specifications, package details, application guidance, and verified drop-in alternatives in a form useful for schematic capture, PCB layout, sourcing, and lifecycle review. It also highlights the differences between electrically similar expanders that use different port architectures.

جێگرەوەکانی جێگۆڕکێ بۆ PCF8574RGTR — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ PCF8574RGTR (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە RoHS Status, I2C Bus Frequency, Interface Type, Interrupt Output, Operating Temperature Range.

Texas Instruments
I2C Bus Frequency: 400 kHz
Interface Type: I2C and SMBus
بەراوردکردن لەگەڵ PCF8574RGTR →
NXP Semiconductors
RoHS Status: Compliant (lead-free)
Interface Type: I2C (SCL/SDA), 2-wire serial
Interrupt Output: Yes, active-low INT pin (open-drain)

PCF8574RGTRG4

✅ جێگرەوەی ڕاستەوخۆ
📦 16-VQFN (RGT) 3 mm x 3 mm
Same PCF8574 function, 8-bit I/O organization, and 16-VQFN land pattern; ordering-code qualification differs, with no quantified electrical difference stated

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

PCA9534RGVR

✅ جێگرەوەی ڕاستەوخۆ
Texas Instruments
📦 16-VQFN (RGT) 3 mm x 3 mm
8 ports · 8 bits · 2.3 V to 5.5 V · 400 kHz · I2C and SMBus · 3 inputs · Up to 8 devices · 1 output

پەیوەندی بۆ نرخ

بینینی داتاشیت →

PCA9534ARGVR

✅ جێگرەوەی ڕاستەوخۆ
📦 16-VQFN (RGT) 3 mm x 3 mm
Same 8-bit I2C expander in a comparable 16-VQFN footprint; push-pull output architecture differs from the PCF8574 quasi-bidirectional ports

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

PCF8574RGTR

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 16-VQFN (RGT) 3 mm x 3 mm
8-bit I2C/SMBus input/output expander with interrupt · 8 ports · 8 bits · 2.5 V to 5.5 V · 100 kHz · I2C/SMBus, two-wire bidirectional bus · Open-drain interrupt output · 3 hardware address inputs

پەیوەندی بۆ نرخ

بینینی داتاشیت →

PCF8574AT/3,518

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
NXP Semiconductors
📦 16-VQFN (RGT) 3 mm x 3 mm
PCF8574AT/3,518 · 8-bit I/O Expander with I2C-bus interface · 8 · I2C (SCL/SDA), 2-wire serial · 100 kHz · 2.5 V to 6 V · 0x38-0x3F (PCF8574A family: 0x38-0x3F) · Quasi-bidirectional (weak pull-up current source)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

PCF8574RGTR تایبەتمەندییەکان

Device Type 8-bit I2C/SMBus input/output expander with interrupt
Number of I/O Ports 8 ports
Number of Bits 8 bits
Supply Voltage Range 2.5 V to 5.5 V
I2C Bus Frequency 100 kHz
Serial Interface I2C/SMBus, two-wire bidirectional bus
Interrupt Output Open-drain interrupt output
Address Inputs 3 hardware address inputs
Port Architecture Quasi-bidirectional input/output ports
مەودای پلەی گەرمیی کارکردن -40 °C to +85 °C
پاکێج 16-pin VQFN (RGT)
Package Dimensions 3 mm x 3 mm
جۆری دامەزراندن Surface mount
Exposed Pad Yes
ئاستی MSL MSL 1 - 260 °C unlimited floor life
دۆخی RoHS RoHS3 compliant
Automotive Qualification Not applicable
دۆخی چرخەی ژیان Active

ڕێکخستنی پینی PCF8574RGTR

QFN-16 Package Pinout Diagram QFN-16 3x3mm, P0.5mm, EP 1.7x1.7mm, JEDEC MO-220. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 QFN-16
پین 1 INT — Open-drain interrupt output
پین 2 SCL — Serial clock input for the I2C/SMBus interface
پین 3 SDA — Bidirectional serial data for the I2C/SMBus interface
پین 4 P0 — Quasi-bidirectional input/output port 0
پین 5 P1 — Quasi-bidirectional input/output port 1
پین 6 P2 — Quasi-bidirectional input/output port 2
پین 7 P3 — Quasi-bidirectional input/output port 3
پین 8 GND — Ground connection
پین 9 P4 — Quasi-bidirectional input/output port 4
پین 10 P5 — Quasi-bidirectional input/output port 5
پین 11 P6 — Quasi-bidirectional input/output port 6
پین 12 P7 — Quasi-bidirectional input/output port 7
پین 13 VDD — Positive supply voltage input
پین 14 A2 — Address input A2
پین 15 A1 — Address input A1
پین 16 A0 — Address input A0

بەکارهێنانە باوەکان

PCF8574RGTR گونجاوە بۆ 6 بەکارھێنانs: Microcontroller GPIO Expansion, Industrial Control Panel Interfaces, LED Status and Indicator Expansion, Appliance Keypad and Switch Interface, Remote Sensor and Discrete Input Hub, Communication Interface Auxiliary Node.

🔧

Microcontroller GPIO Expansion

The PCF8574RGTR is appropriate when a microcontroller has too few pins for a control panel, keypad, relay bank, or status display. Its eight ports operate from the same 2.5 V to 5.5 V supply range as many 3.3 V and 5 V controllers, while the 100 kHz I2C interface preserves the controller's other pins. This is particularly useful with small devices such as the ATTINY13A-SUR, where eight additional general-purpose lines can eliminate multiplexers and reduce routing complexity. Firmware should define each port as input or output, account for the quasi-bidirectional drive behavior, and use the interrupt line when polling overhead must be reduced.

🏭

Industrial Control Panel Interfaces

A PCF8574RGTR can consolidate pushbuttons, selector switches, status lamps, and relay-control outputs into one compact I2C node. Its 16-pin 3 mm by 3 mm VQFN package leaves more board area available for power components and connectors than a larger 16-pin SOIC, while the -40 °C to +85 °C rating supports industrial-temperature environments. The open-drain interrupt output allows the controller to detect switch activity without continuously reading the bus. Use pull-up resistors appropriate to the bus voltage, and keep the compact footprint's exposed pad connected to the ground plane for both electrical and thermal performance.

💡

LED Status and Indicator Expansion

The eight quasi-bidirectional ports of the PCF8574RGTR can drive low-current LED indicators or control the enable inputs of upstream driver devices. A single 3.3 V I2C bus connection replaces several dedicated microcontroller pins, making the expander useful in display, instrument, and appliance controllers where panel space is limited. Because the ports include a weak output driver, high-current LEDs should use transistor or MOSFET drivers rather than being connected directly. Confirm the continuous sink-current limit of every driven output in the manufacturer datasheet, and test the selected resistor value against the intended brightness and supply voltage.

📱

Appliance Keypad and Switch Interface

The PCF8574RGTR is well suited to reading a matrix or bank of appliance controls while also driving a small number of status signals. Its three address inputs permit several expanders to share one I2C bus, and the interrupt output lets the appliance controller sleep between user actions. The 2.5 V minimum supply accommodates low-voltage control rails, while the 100 kHz bus rate provides ample bandwidth for short button reads. Because the device uses quasi-bidirectional ports, design the switch inputs with suitable pull-up or pull-down arrangements so every inactive line reaches a valid logic level.

🧩

Remote Sensor and Discrete Input Hub

A PCF8574RGTR can act as a remote input hub for dry contacts, limit switches, interlocks, and other discrete signals distributed across a control board. Eight inputs share one I2C address, and the interrupt line provides a hardware indication that at least one input changed. This arrangement reduces the number of interconnects between a central controller and a peripheral board. Select pull-up or pull-down networks for reliable inactive-state levels, maintain separate return paths for noisy relays, and test debounce timing in firmware because mechanical contacts can generate multiple transitions during one physical event.

🌐

Communication Interface Auxiliary Node

The PCF8574RGTR can supplement a communications processor that needs local control lines for modem, transceiver, or peripheral-enable functions. Its I2C interface allows auxiliary control logic to share the bus with transceivers such as the SP3232EUEY-L, avoiding dedicated GPIO pins on the main processor. The small VQFN package is advantageous in multi-function boards where connector placement limits available area. Address the auxiliary node through the A0, A1, and A2 straps, keep its interrupt trace away from switching edges, and confirm that every enabled peripheral has a defined state during controller reset and bus startup.

What is the operating voltage of the PCF8574RGTR?
The PCF8574RGTR operates from 2.5 V to 5.5 V according to the Texas Instruments PCF8574 product page. This range supports both 3.3 V and 5 V systems, provided that the I2C pull-up voltage and every attached peripheral remain compatible with the selected supply. The manufacturer datasheet describes the device as an 8-bit remote I/O expander for the two-line bidirectional bus and includes detailed operating-condition information for design verification.
How many GPIO pins can the PCF8574RGTR add to a microcontroller?
The PCF8574RGTR adds eight general-purpose I/O ports to an I2C or SMBus host. Each port can be configured as a logic input or quasi-bidirectional output, allowing the expander to read switches and control indicators, relays, or logic inputs. Texas Instruments identifies the device as an 8-bit I2C/SMBus I/O expander with interrupt, so the eight ports are reached over a two-wire interface rather than individual host-controller pins.
Where can I download the PCF8574RGTR datasheet PDF?
The manufacturer datasheet is available from the Texas Instruments literature server at https://www.ti.com/lit/ds/symlink/pcf8574.pdf. It describes the remote 8-bit I/O expander for the I2C bus, including the electrical characteristics, port behavior, address configuration, timing, and application information. Use the manufacturer document as the primary reference for PCB footprint, exposed-pad handling, and operating limits when designing a new layout.
What is the PCF8574RGTR pinout?
The 16-pin VQFN pinout provides INT, SCL, SDA, eight I/O ports, ground, supply, and three address inputs. Pin 1 is INT, pins 2 and 3 are SCL and SDA, pins 4 through 7 are P0 through P3, pin 8 is GND, pins 9 through 12 are P4 through P7, pin 13 is VDD, and pins 14 through 16 are A2, A1, and A0. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
What is the best drop-in replacement for the PCF8574RGTR?
The closest verified same-footprint replacement is the Texas Instruments PCF8574RGTRG4, which retains the PCF8574RGTR pin arrangement and core 8-bit I/O-expander function. The PCA9534RGVR and PCA9534ARGVR are electrically similar 8-bit I2C expanders, but their output-driver architecture differs, so firmware and pull-up arrangements should be reviewed before substitution. The Texas Instruments option is preferred when functional identity is more important than a different port-drive implementation.
Can the PCA9534ARGVR replace the PCF8574RGTR?
The PCA9534ARGVR can serve as a redesign-level alternative because it is also an 8-bit I2C I/O expander in a comparable small-footprint package and supports a similar 2.3 V to 5.5 V supply range. It is not a perfect functional drop-in because its output stage uses push-pull drivers rather than the PCF8574's quasi-bidirectional ports, which can change current, polarity, and firmware behavior. Verify every connected load and pin arrangement against the relevant datasheets.
When should I choose the PCF8574RGTR instead of another 8-bit I2C expander?
Choose the PCF8574RGTR when you need eight quasi-bidirectional ports, a compact 3 mm by 3 mm footprint, an interrupt output, and established compatibility with 3.3 V or 5 V I2C systems. It is especially suitable for passive pull-up inputs and modest logic-level loads. Choose a push-pull expander instead when outputs must source current more aggressively or when firmware benefits from strongly defined output states.
Is the PCF8574RGTR suitable for a 3.3 V microcontroller system?
Yes, the PCF8574RGTR is suitable for a 3.3 V system because its specified operating range of 2.5 V to 5.5 V includes the 3.3 V rail. Pull SDA and SCL up to 3.3 V rather than to 5 V when the host uses 3.3 V logic. Also check that connected sensors, relays, or indicator drivers have 3.3 V-compatible inputs and that their output levels meet the expander's input thresholds.
How many I2C addresses can PCF8574 devices use?
Three address inputs, A0 through A2, let the PCF8574RGTR occupy multiple addresses on the same I2C bus. Texas Instruments identifies the device as an 8-bit I2C/SMBus expander, and the package exposes three hardware address inputs. Set each address strap to the required logic level before the device is enabled, then confirm the resulting seven-bit bus address in firmware rather than relying only on the software address constant.
What are the key specifications of the PCF8574RGTR that engineers should know?
The PCF8574RGTR provides eight I/O ports, a 2.5 V to 5.5 V supply range, a 100 kHz I2C interface, an interrupt output, and three address inputs in a 16-pin 3 mm by 3 mm VQFN package. Its -40 °C to +85 °C temperature range suits industrial-temperature operation. The port architecture and exposed-pad connection are as important as the headline pin count when planning firmware and layout.
Does the PCF8574RGTR need pull-up resistors on SDA and SCL?
Yes, SDA and SCL normally require pull-up resistors because the I2C bus uses open-drain signaling. Select the resistance from the bus voltage, total capacitance, and the highest clock rate of 100 kHz, then validate the rise time on the assembled board. Avoid excessively strong pull-ups because they increase the low-state sink current required from the bus driver.
What can replace the PCF8574RGTR in an existing PCB design?
The PCF8574RGTRG4 is the most direct replacement for the same Texas Instruments PCF8574 family because it preserves the device type, 8-port organization, address inputs, and interrupt function. A PCA9534-family device can also be considered when the board can tolerate different output-drive behavior. Any substitution requires checking the footprint, exposed pad, address strapping, interrupt polarity, port-current limits, and firmware assumptions.
Is the PCF8574RGTR active or discontinued?
The PCF8574RGTR is listed as active. Texas Instruments lists PCF8574RGTR as a 16-pin RGT package option with an operating temperature range of -40 °C to +85 °C, and a component-lifecycle source also identifies PCF8574 as active. Check the manufacturer orderable-parts page before committing a long-term production design because availability and lead time can change independently of lifecycle status.
Where can I buy the PCF8574RGTR and check its current price?
Use the Request a Quote form on this page to request the current unit price, stock position, minimum order quantity, and lead time for the Texas Instruments PCF8574RGTR. The manufacturer part-details page confirms the exact RGT ordering option, while distributor listings provide market availability information. Request a written quotation when production scheduling depends on a committed delivery date or volume allocation.
How does the PCF8574RGTR interrupt work in an embedded design?
The PCF8574RGTR provides an open-drain interrupt output that can notify the host when a port input changes. The host can then read the port register over I2C to determine which input changed, reducing unnecessary bus traffic compared with continuous polling. Because the interrupt is open drain, it can be wired to a shared system interrupt line, and the host software should still include timeout and recovery handling for bus faults.
What are the main differences between the PCF8574RGTR and PCF8574RGYR?
PCF8574RGTR and PCF8574RGYR both belong to the Texas Instruments PCF8574 8-bit I2C/SMBus I/O-expander family, but their packages differ. PCF8574RGTR uses a 16-VQFN 3 mm by 3 mm RGT package, while PCF8574RGYR uses a 20-VQFN 3.5 mm by 4.5 mm package. They are therefore functional family alternatives but are not land-pattern-compatible; PCF8574RGTR is the appropriate choice for a 16-pin compact footprint.

داتای سەرچاوەی ئەندازیاری بۆ PCF8574RGTR — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the PCF8574RGTR for a new compact 3.3 V or 5 V design that needs eight conventional quasi-bidirectional I/O ports, three addressable bus nodes, and an open-drain interrupt. It is particularly suitable for pull-up-based switch inputs and modest logic-level loads. Choose PCF8574RGTRG4 when that exact function and footprint are needed but the preferred ordering suffix is unavailable. Choose a PCA9534RGVR or PCA9534ARGVR only after checking the push-pull output behavior, port current, reset defaults, and firmware assumptions; their stronger output drivers can be beneficial but may alter system behavior. Do not substitute PCF8574RGYR on an existing PCF8574RGTR board because its 20-VQFN package has a different land pattern. For designs needing more than eight ports, multiple PCF8574 devices can share the I2C bus through the A0, A1, and A2 address straps.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە PCF8574RGTRG4 PCA9534RGVR PCA9534ARGVR PCF8574A
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 16-VQFN (RGT) 3 mm x 3 mm 16-VQFN (RGT) 3 mm x 3 mm 16-VQFN (RGT) 3 mm x 3 mm 16-VQFN (RGT) 3 mm x 3 mm 16-VQFN (RGT) 3 mm x 3 mm
I/O Ports 8 8 8 8 8
Output Architecture Quasi-bidirectional Quasi-bidirectional Push-pull Push-pull Quasi-bidirectional
Address Inputs 3 3 3 3 3
Interrupt Output Open-drain interrupt Open-drain interrupt Open-drain interrupt Open-drain interrupt Open-drain interrupt

جیاکەرەوە سەرەکییەکان

  • Directly preserves the PCF8574 port behavior (بەراورد بەPCA9534RGVR)
  • Compact 16-pin footprint for space-constrained boards (بەراورد بەPCF8574RGYR)
  • Supports 3.3 V and 5 V systems over a 2.5 V to 5.5 V range (بەراورد بەPCA9534RGVR)
  • Three hardware address inputs support multi-node buses (بەراورد بەPCF8574RGTRG4)

تێبینییەکانی دیزاین

Route SDA and SCL as short, matched traces away from switching nodes and relay-coil edges, and place their pull-up resistors close to the bus master. The PCF8574RGTR uses a 3 mm by 3 mm 16-pin VQFN footprint, so verify the land pattern and exposed-pad dimensions against the current manufacturer package drawing. Tie the exposed pad to the ground plane with short vias; do not leave it unconnected because the pad provides the package's principal thermal and electrical return path.

Calculate the I2C pull-up value from the bus voltage, total trace and component capacitance, and the 100 kHz maximum clock rate. Confirm the resulting rise time and sink current before layout release. The quasi-bidirectional port stage should be used mainly for inputs, conventional CMOS inputs, and modest logic-level loads; use external drivers for LEDs, relays, or other devices that exceed the port current capability. Firmware must also avoid relying on a port remaining strongly driven high when another device can pull it low.

Do not confuse PCF8574RGTR with PCF8574RGYR: both are in the same device family, but the latter uses a 20-VQFN 3.5 mm by 4.5 mm package and is not land-pattern-compatible. Likewise, verify output-drive behavior when considering a PCA9534-family substitution. Confirm the A0, A1, and A2 strap levels, define port input states during reset, and use the open-drain interrupt with an appropriate pull-up so the host can reliably detect asserted interrupts.

زانیاری پابەندبوون

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The component information identifies the PCF8574RGTR as RoHS3 compliant with MSL 1, 260 °C unlimited floor life. The REACH status is not established, and lead-free, halogen-free, and conflict-minerals declarations require manufacturer confirmation.

داتا پشتڕاستکراوەتەوە لە: 2026-11-19 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

pcf8574rgtr umw PCF8574RGTR datasheet PCF8574RGTR datasheet pdf PCF8574RGTR pinout PCF8574RGTR VQFN-16 pinout Texas Instruments PCF8574RGTR PCF8574RGTR equivalent PCF8574RGTR drop-in replacement PCF8574RGTR vs PCA9534RGVR PCF8574RGTR 8-bit I2C expander PCF8574RGTR application circuit PCF8574RGTR price PCF8574RGTR stock PCF8574RGTR footprint

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments PCF8574 PCF8574RGTR PCF8574RGTRG4 PCF8574RGYR PCA9534RGVR PCA9534ARGVR I2C SMBus I/O expander interface IC semiconductor quasi-bidirectional GPIO push-pull GPIO interrupt output 100 kHz I2C 2.5 V to 5.5 V 16-VQFN RGT QFN package family surface-mount package 3 mm x 3 mm footprint RoHS REACH MSL 1 industrial control panel microcontroller GPIO expansion
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ