PCA9534RGVR - 8-Bit I2C I/O Expander | Texas Instruments
MPN: PCA9534RGVR ✓ فعالPCA9534RGVR جائزہ
An I/O expander is an interface IC that extends the number of digital input/output lines available to a controller. The PCA9534 belongs to the broader hierarchy of I2C interface controllers, SMBus peripherals, GPIO expanders, and interface ICs. It communicates with a host through the two-wire SDA and SCL bus, while the eight port pins can be configured individually as inputs or outputs through internal registers.
Key device features include three address pins, A0, A1, and A2, which allow up to eight PCA9534 devices to share one I2C or SMBus bus. The interrupt output provides a change-detection path to the host, while configuration registers support input, output, and quasi-bidirectional operating modes. According to the manufacturer product page, the device operates from 2.3 V to 5.5 V and is compatible with 400 kHz I2C signaling.
The PCA9534 uses a host-controlled serial interface rather than dedicating a microcontroller port to each external signal. Address selection is established by the A0, A1, and A2 pins, and the controller accesses configuration, input, output, and interrupt-related registers through the bus. This architecture makes the device suitable for systems whose fixed controller pin count is insufficient for relays, sensors, LEDs, keys, or other digital peripherals.
Typical uses include industrial control panels, battery-powered instruments, automated test equipment, and embedded systems with multiple digital loads. It can also provide bus-managed GPIO nodes in communications equipment, measurement systems, and compact controller boards. The device is particularly useful when the required expansion is eight lines rather than a large, high-speed parallel interface.
Designers should treat SDA and SCL as bus signals requiring suitable pull-up resistors and careful board layout. Account for address-pin strapping, power-supply decoupling, and the electrical characteristics of every attached peripheral. Although the PCA9534 is pin-to-pin and I2C-address compatible with the PCF8574, the manufacturer states that software changes are required because of the PCA9534 register enhancements.
This page combines manufacturer specifications, sourcing guidance, package details, application engineering notes, and a strict same-package replacement comparison. It is designed to help engineers determine whether the PCA9534RGVR fits a voltage range, bus topology, interrupt architecture, and PCB footprint without relying on a basic distributor listing alone.
کے لیے ڈراپ اِن متبادل PCA9534RGVR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PCA9534RGVR (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف I2C Bus Frequency, Package Dimensions.
PCA9534RGVRG4
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PCA9534RGVR تفصیلات
| Number of I/O Ports | 8 ports |
| I/O Port Resolution | 8 bits |
| آپریٹنگ سپلائی وولٹیج | 2.3 V to 5.5 V |
| I2C Bus Frequency | 400 kHz |
| انٹرفیس ٹائپ | I2C and SMBus |
| Address Configuration Inputs | 3 inputs |
| Devices per Bus | Up to 8 devices |
| Interrupt Outputs | 1 output |
| Configuration Registers | Present |
| Package Pin Count | 16 pins |
| Package Dimensions | 4 x 4 mm |
| Package Type | 16-pin VQFN |
| ماؤنٹنگ ٹائپ | Surface mount |
| RoHS اسٹیٹس | RoHS3 compliant |
| REACH Status | Not specified |
| Moisture Sensitivity Level | MSL 2, 260 C, 1 year |
PCA9534RGVR پن کنفیگریشن
| پن 1 | INT — Interrupt output |
| پن 2 | P0 — Bidirectional I/O port 0 |
| پن 3 | P1 — Bidirectional I/O port 1 |
| پن 4 | P2 — Bidirectional I/O port 2 |
| پن 5 | P3 — Bidirectional I/O port 3 |
| پن 6 | P4 — Bidirectional I/O port 4 |
| پن 7 | P5 — Bidirectional I/O port 5 |
| پن 8 | P6 — Bidirectional I/O port 6 |
| پن 9 | P7 — Bidirectional I/O port 7 |
| پن 10 | A2 — Address input 2 |
| پن 11 | A1 — Address input 1 |
| پن 12 | A0 — Address input 0 |
| پن 13 | SDA — Serial data input/output |
| پن 14 | SCL — Serial clock input |
| پن 15 | VSS — Ground reference |
| پن 16 | VDD — Positive supply voltage |
عام استعمالات
PCA9534RGVR کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Control Panel I/O Expansion, Battery-Powered Test and Measurement, Communications Equipment Status Inputs, LED and Relay Control Expansion, Embedded Sensor and Key Interface, Compact Automation and Robotics Control.
Industrial Control Panel I/O Expansion
The PCA9534RGVR is suitable for adding keypad inputs, status indicators, relay-control outputs, and discrete sensor inputs to a compact industrial controller. Its eight ports share one 2-wire interface at up to 400 kHz, while A0, A1, and A2 permit several expanders to occupy distinct addresses on the same bus. The 2.3 V to 5.5 V operating range accommodates common industrial control rails. The interrupt output can notify the controller when an input state changes, avoiding continuous polling. Port setup should be completed through the configuration registers before external loads are enabled, and external pull-ups should be added wherever a port must actively source a defined HIGH level.
تجویز کردہ
Battery-Powered Test and Measurement
The PCA9534RGVR can expand a low-power measurement controller with eight digital lines for fixture control, limit comparison, and instrument triggering. Operating from 2.3 V to 5.5 V supports systems built around low-voltage supplies, and the I2C interface reduces the number of host-controller pins required. When most ports remain low between measurements, the external pull-up network can dominate standby dissipation, so resistor values and state control should be reviewed. The 400 kHz bus rate is suitable for configuration commands and low-speed status updates rather than continuous high-rate waveform sampling. Firmware should configure ports and masks interrupts before enabling connected peripherals.
تجویز کردہ
Communications Equipment Status Inputs
The PCA9534RGVR is useful in communications equipment that needs more status, fault, or control lines than the host processor can expose directly. Eight ports can represent module-present, alarm, reset, or peripheral-enable signals while using only SDA, SCL, and an optional interrupt connection. The A0, A1, and A2 inputs allow multiple identification or configuration nodes on a shared bus, helping isolate subsystems on one controller. At the 2.3 V minimum supply voltage, the device fits low-voltage logic domains, although every attached signal must remain within its voltage limits. Firmware should validate pin direction and mask unintended wake events when the interrupt line is connected to a shared controller resource.
تجویز کردہ
LED and Relay Control Expansion
The PCA9534RGVR provides a compact way to control LEDs, relay drivers, and discrete loads when a host controller has limited output pins. The eight ports are grouped logically on a register-addressed device, allowing software to update multiple outputs through the I2C bus and use the interrupt line for monitoring. The 16-pin 4 x 4 mm VQFN saves board area compared with a discrete 8-bit parallel interface. Loads that exceed the port ratings must use suitable transistor or driver circuitry, and inductive loads require appropriate suppression. External port pull-ups should be sized for the required output state and current, while firmware should initialize outputs to a safe inactive condition before enabling attached hardware.
تجویز کردہ
Embedded Sensor and Key Interface
The PCA9534RGVR can gather digital sensor states, selector switches, and push-button events while preserving controller I/O for higher-bandwidth functions. Its interrupt output supports change-driven handling when the host does not need to poll all eight inputs continuously. Address strapping permits multiple expansion nodes, and the 2.3 V to 5.5 V range covers several common logic systems. Mechanical inputs may bounce, so firmware should use debouncing appropriate to the switch type rather than assuming every interrupt is a valid transition. External pull-ups can maintain defined input states, while the configuration registers should be set for input or output operation before external circuitry is energized.
تجویز کردہ
Compact Automation and Robotics Control
The PCA9534RGVR is appropriate for distributed digital I/O in compact automation equipment where several nodes must communicate over a shared bus. Eight independently configurable ports can handle discrete actuator commands and equipment interlocks, while A0, A1, and A2 provide straightforward bus addressing. The 400 kHz I2C rate supports typical command and status traffic, and the small 4 x 4 mm VQFN supports compact controller boards. The interrupt output can prompt the controller to inspect changed inputs, reducing unnecessary polling. Designers should account for electrical isolation, actuator transients, grounding, and safe power-up states because the expander is intended for logic-level signaling rather than direct high-power load control.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PCA9534RGVR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PCA9534RGVRG4 |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 16-pin VQFN (4 x 4 mm) | 16-pin VQFN (4 x 4 mm) |
| I/O Port Count | 8 ports | 8 ports |
| Operating Supply Voltage | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| I2C Bus Frequency | 400 kHz | 400 kHz |
| Interface | I2C and SMBus | I2C and SMBus |
| Address Inputs | 3 inputs | 3 inputs |
| Interrupt Output | 1 output | 1 output |
| Configuration Registers | Present | Present |
اہم امتیازی خصوصیات
- Identical core interface and port capacity (بمقابلہPCA9534RGVRG4)
- Direct pin-to-pin PCB reuse (بمقابلہPCA9534RGVRG4)
- Eight shared-bus expansion lines (بمقابلہPCA9534RGVRG4)
ڈیزائن نوٹس
Place the device close to the SDA and SCL bus routing and keep the address-strapping traces away from long high-impedance branches. Confirm the exposed-pad connection and land pattern against the 4 x 4 mm VQFN package drawing. Maintain the recommended ground-plane connection, route supply current away from sensitive signal paths, and place the local supply-decoupling capacitor close to VDD and ground pins.
Size SDA and SCL pull-ups from the bus voltage, total capacitance, leakage, and required rise time rather than using one resistor value for every board. An undersized resistor increases low-level sink current, while an oversized resistor can produce slow rising edges and ringing. Confirm that the complete bus, including PCA9534 inputs and other attached devices, remains compatible with 400 kHz operation.
Do not assume that a PCA9534 can replace a PCF8574 without changing firmware. Texas Instruments states that the devices are pin-to-pin and I2C-address compatible, but software changes are required for the PCA9534 register enhancements. Also avoid assuming that a generic PCA9534 orderable number is a PCB-level drop-in replacement until its exact package, suffix, temperature range, and pinout have been verified.
Budget the PCA9534 supply current together with port load current and pull-up dissipation. External port pull-ups can create a continuing path to VDD when a port is held LOW, so resistor values directly affect low-power operation. Select external loads that remain within the electrical limits stated in the manufacturer datasheet and add appropriate buffering for high-current or inductive loads.
تعمیل کی معلومات
The part listing identifies RoHS3 compliance and MSL 2 at 260 C for one year. No manufacturer statement confirming AEC-Q100 qualification, lead-free construction, halogen-free construction, or conflict-minerals compliance was identified.