NXP Semiconductors

PCA9646D - 4-Channel 1 MHz I2C Bus Buffer | NXP

MPN: PCA9646D ✗ کۆتایی ژیان
16-pin SOIC, 3.90 mm body width Package 1 MHz Speed
MOQ: 1 |

PCA9646D گشتی

The NXP Semiconductors PCA9646D is a buffered four-channel 2-wire bus switch operating up to 1 MHz in a 16-pin SOIC package. Each of its four outputs can be enabled independently through the programmable control register, allowing unused branches to remain isolated. The monolithic CMOS device supports I2C-bus, SMBus, PMBus, and compatible two-wire systems, with electrical isolation between all five branches.

A buffered 2-wire bus switch is an interface IC that regenerates bus signals while separating capacitive loads into independently controlled branches. In the hierarchy of semiconductor components, it belongs to the bus switch and interface-switch class, within logic and interface ICs. This differs from a basic multiplexer because the buffered outputs are designed to drive larger bus capacitance and maintain signal quality as branches are added.

The PCA9646D provides four independently enabled output channels, a maximum operating frequency of 1 MHz, and support for five branches when the input bus is included. The NXP datasheet states that the device can support up to five 400 pF loads for Fm+ I2C-bus operation at 1 MHz. At lower operating frequencies, the stated capability extends to five 4 nF loads. Every I/O is impedance-isolated from the others, helping prevent inactive branches from degrading signal integrity.

Control is performed through a programmable register, allowing any combination of the four outputs to be enabled. Multiple PCA9646 devices may also be cascaded when a system needs more segmented branches. This architecture is useful where bus capacitance, propagation delay, or branch loading would make a direct multi-device connection impractical. The device is designed for industrial-temperature operation from -40°C to +85°C and is supplied in a surface-mount 16-pin SOIC package.

Typical uses include isolating sensors on an I2C bus, connecting LED controllers to PMBus-compatible systems, partitioning SMBus devices, and supporting multi-branch industrial control boards. The four independently controlled outputs are especially useful when several devices share the same bus address or when a branch must be disconnected to prevent leakage from an inactive peripheral.

PCB design should preserve short, symmetric routing between the upstream bus and each output branch, while keeping ground returns continuous. The input and output nets must observe the capacitance limits stated in the manufacturer datasheet because longer branches or excessive loading can reduce rise time and cause communication errors even when the nominal clock is below 1 MHz.

This page consolidates the device architecture, operating limits, branch-loading capabilities, lifecycle information, and application guidance into a practical engineering reference for I2C-bus and SMBus buffer design.

جێگرەوەکانی جێگۆڕکێ بۆ PCA9646D — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ PCA9646D (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package.

NXP Semiconductors
Package: 16-SOIC (0.154 in, 3.90 mm width)
بەراوردکردن لەگەڵ PCA9646D →

PCA9546AD,112

✅ جێگرەوەی ڕاستەوخۆ
NXP Semiconductors
📦 SOIC-16
4-channel bidirectional translating I2C-bus switch with reset · I2C, SMBus · 2.3 V to 5.5 V · 4 (1 upstream pair, 4 downstream SCx/SDx pairs) · 30 ohm · Active-LOW RESET · 3 (A0, A1, A2) - up to 8 devices on one bus · 1.8 V, 2.5 V, 3.3 V and 5 V buses

پەیوەندی بۆ نرخ

بینینی داتاشیت →

PCA9646D تایبەتمەندییەکان

Product Type Buffered 4-channel 2-wire bus switch
Number of Output Channels 4 channels
Maximum Bus Frequency 1 MHz
Total Supported Branches 5 branches including the input branch
Maximum Fm+ I2C-Bus Loading at 1 MHz 5 × 400 pF
Maximum Loading at Lower Frequencies 5 × 4 nF
Process Technology Monolithic CMOS
Output Control 4 independently programmable outputs
Bus Compatibility I2C-bus, SMBus, PMBus, and similar 2-wire systems
Branch Isolation All I/O channels impedance-isolated
مەودای پلەی گەرمیی کارکردن -40°C to +85°C
پاکێج 16-pin SOIC, 3.90 mm body width
جۆری دامەزراندن Surface mount
Standard Packaging Tape and reel

ڕێنمایی ڕێکخستنی پینی PCA9646D 16-pin soic, 3.90 mm body width

ڕێکخستنی پین بۆ PCA9646D (پاکێجی 16-pin soic, 3.90 mm body width). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 16-pin soic, 3.90 mm body width بۆ PCA9646D

هیچ داتای وردی پینئاوت بەردەست نییە بۆ PCA9646D.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

PCA9646D گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Bus Segmentation, PMBus Power Management Isolation, SMBus Equipment Isolation, Multi-Branch LED Control, Test and Measurement Fixture, Embedded Communication Port Isolation.

🏭

Industrial Sensor Bus Segmentation

The PCA9646D fits industrial sensor networks where several remote I2C devices create excessive capacitive loading on one bus segment. Place the device between the controller and four sensor branches, then use the programmable control register to enable only the populated branches. At 1 MHz, the NXP datasheet specifies support for five 400 pF loads, allowing the bus to remain segmented into controlled paths. The isolation between channels can reduce the effect of an unused or inactive sensor branch on signal rise time. Keep each branch physically short and verify that its total capacitance, pull-up resistance, and propagation delay remain within the system timing budget.

⚡

PMBus Power Management Isolation

The PCA9646D is appropriate for PMBus-based power systems in which several controllers, monitors, or converters must share a two-wire management bus. Its four independently enabled outputs can isolate power-management branches and prevent one heavily loaded peripheral from dominating the complete bus. The device supports PMBus and similar two-wire systems at rates up to 1 MHz, while the buffered outputs help preserve edge quality across segmented branches. Configure the control register for the required channel combination and use the NXP timing and capacitance limits as the basis for pull-up selection. This approach is especially helpful when converters are placed at different distances from the system controller.

🖥️

SMBus Equipment Isolation

The PCA9646D can divide an SMBus network into independently managed branches for computer, storage, or industrial test equipment. Its four programmable outputs allow firmware to disconnect unused ports during boot, isolate a peripheral during recovery, or maintain communication with active devices when one branch is inactive. The buffered architecture operates up to 1 MHz, and the manufacturer specifies five 400 pF branch loads at that frequency. Designers should account for the added propagation delay of each buffer stage, select pull-ups for the worst branch capacitance, and avoid configuring the device as a general-purpose bidirectional multiplexer without reviewing the control logic in the datasheet.

💡

Multi-Branch LED Control

The PCA9646D can support compact LED-control boards that distribute multiple lighting channels or drivers over a common two-wire control bus. Rather than attaching every LED controller directly to one long bus, the device provides four independently enabled outputs that partition the network and can leave unused driver branches isolated. This arrangement helps manage branch capacitance while retaining operation up to 1 MHz. The application benefits when LED controllers use compatible two-wire protocols and require selective startup. Use short, symmetric traces, confirm pull-up placement, and account for buffer propagation delay when timing dimming commands across multiple branches.

🧩

Test and Measurement Fixture

The PCA9646D is useful in test and measurement fixtures that connect several instruments, programmable components, or sensor adapters over a shared two-wire bus. Independent output enables let the fixture isolate unpopulated or faulted branches and reduce their influence on the active test path. With operation up to 1 MHz and support for five 400 pF loads at that rate, the device can organize higher-capacitance fixture wiring into controlled segments. The buffered outputs help maintain usable rise times when the master controller is located away from the test hardware. Validate the complete timing budget, including cable capacitance, connector parasitics, pull-up strength, and the additional delay introduced by the buffered switch.

🔧

Embedded Communication Port Isolation

The PCA9646D can isolate communication ports on embedded boards that serve several external sensors, memory devices, or interface adapters. Its four output channels may be enabled in any combination, allowing firmware to separate unused connectors and preserve a clean upstream bus during startup or fault recovery. This is particularly useful where cable-connected accessories add capacitance beyond the comfortable loading of a direct board bus. The NXP specification supports up to five 400 pF branches at 1 MHz, enabling a compact port-partitioning strategy. Check input and output rise-time limits, maintain a continuous return path, and confirm that the control interface does not conflict with other bus-management devices on the same board.

What is the PCA9646D used for?
The PCA9646D is a buffered four-channel 2-wire bus switch used to segment I2C-bus, SMBus, PMBus, and similar communication buses. It provides four independently enabled outputs and can support five branches, including the upstream branch, at up to 1 MHz. According to the NXP PCA9646 datasheet, each I/O is impedance-isolated, helping reduce the loading impact of inactive branches on the master bus.
How many channels and branches does the PCA9646D support?
The PCA9646D contains four independently controlled output channels and supports five total branches when the upstream input is counted. The NXP datasheet specifies that each output may be enabled in any combination through the programmable control register. This branch architecture is useful when a system has more I/O devices or a longer load than can safely be attached to one undivided two-wire bus.
What is the maximum operating frequency of PCA9646D?
The PCA9646D operates up to 1 MHz. Its buffered outputs are intended to maintain communication quality when bus capacitance is distributed across multiple branches. According to the NXP datasheet, the device supports five 400 pF loads for Fm+ I2C-bus operation at 1 MHz, while lower-frequency operation can accommodate up to five 4 nF loads.
Can the four PCA9646D outputs be enabled independently?
Yes, all four PCA9646D outputs can be enabled in any combination by programming the control register. This allows a system designer to disconnect an unused or temporarily inactive peripheral branch while keeping other branches operating. The NXP datasheet identifies the four outputs as independently enabled and electrically isolated from one another through impedance isolation.
What is the difference between PCA9646D and PCA9546AD,112?
The PCA9646D is a buffered four-channel 2-wire bus switch optimized for fan-out and branch isolation, while the PCA9546AD,112 is identified in cross-reference records as a 16-pin SOIC 2.3 V to 5.5 V I2C or SMBus interface IC. The PCA9646D is preferable when branch isolation and buffered signal regeneration are required, although final substitution still requires verification of every control-register and logic-level detail against the manufacturer datasheets.
When should I choose PCA9646D instead of PCA9546AD,112?
Choose the PCA9646D when the design needs four independently controlled buffered outputs for a segmented I2C-bus, SMBus, or PMBus network. The PCA9546AD,112 is appropriate when a basic four-channel bus multiplexer is sufficient and the design does not depend on the PCA9646D's buffered branch architecture. Verify pin, register, voltage, and timing compatibility before using either part as a replacement.
Is PCA9646D suitable for I2C and SMBus systems?
The PCA9646D is suitable for I2C-bus, SMBus, PMBus, and other systems based on similar two-wire principles. Its four buffered outputs can isolate capacitive loads while maintaining operation up to 1 MHz. According to the NXP datasheet, the device supports five 400 pF branches at 1 MHz for Fm+ I2C-bus operation, making it suitable for multi-branch industrial and embedded control systems.
Where can I download the PCA9646D datasheet PDF?
The official PCA9646D datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/PCA9646.pdf. Use the manufacturer document for the complete pin description, control-register definition, timing characteristics, electrical limits, and recommended application circuit. The NXP product page at https://www.nxp.com/part/PCA9646D provides the archived product overview and additional historical information.
Where can I find the PCA9646D pinout?
The PCA9646D pinout is identified in the official NXP PCA9646 datasheet under the package and pin-description information. The device uses a 16-pin SOIC package, but the complete numbered pin list should be assigned directly from the manufacturer's pin-description table rather than inferred from a generic SOIC-16 drawing. This prevents incorrect connections to the supply, ground, address, and control pins.
How much bus capacitance can PCA9646D drive at 1 MHz?
At 1 MHz, the PCA9646D can support five 400 pF loads for Fm+ I2C-bus operation. This statement comes from the NXP PCA9646 datasheet and includes the maximum specified branch arrangement. At lower operating frequencies, the datasheet states that the device can support five 4 nF loads, so frequency and capacitance must be considered together when designing the bus.
Can multiple PCA9646 devices be used on one bus?
Yes, multiple PCA9646 devices may be used when a system needs more branches or additional bus segmentation. The NXP datasheet specifically notes that more than one PCA9646 may be connected. Designers should account for address selection, control-register configuration, propagation delay, and the aggregate loading presented to the upstream bus when planning the hierarchy.
What is the lifecycle status of PCA9646D?
The PCA9646D is obsolete. NXP describes its product-page content as archived and no longer updated, and a distributor product listing also identifies the PCA9646D,118 as obsolete. For new production, request current lifecycle and sourcing options through the Request a Quote form on this page. Legacy systems can use the same form to ask about availability, lot traceability, and obsolete-part handling.
What can replace the PCA9646D?
The closest documented candidate is the NXP PCA9546AD,112, which is listed as a 16-pin SOIC I2C and SMBus interface device with a 2.3 V to 5.5 V operating range. It offers the same channel count and package, but its control and buffering behavior must be checked before substitution. No cross-brand drop-in replacement was established, so board-level pin, register, and timing verification is mandatory.
Is PCA9646D the same as PCA9546AD,112?
No. The PCA9646D is a buffered four-channel 2-wire bus switch, while the PCA9546AD,112 is classified as an I2C and SMBus interface IC. Both are associated with 16-pin SOIC packages, but sharing a package does not prove functional interchangeability. The PCA9646D's programmable channel enable, isolation behavior, and bus timing must be reconciled with the PCA9546AD,112 before interchange.
What are the key specifications engineers should know about PCA9646D?
The key PCA9646D specifications are four independently enabled channels, operation up to 1 MHz, a 16-pin SOIC package, and support for five branches including the upstream bus. The NXP datasheet states that all I/O channels are impedance-isolated and gives loading limits of five 400 pF at 1 MHz or five 4 nF at lower frequencies. The device also supports I2C-bus, SMBus, PMBus, and similar two-wire systems.
Where can I buy PCA9646D, and what is its price and lead time?
Use the Request a Quote form on this page to inquire about PCA9646D price, stock, minimum order quantity, and current lead time. The part is obsolete, so supply may depend on remaining factory inventory, previously manufactured lots, and authorized-channel traceability. Request the lot date, packaging suffix, and quality documentation when obtaining a quote for an obsolete device.

داتای سەرچاوەی ئەندازیاری بۆ PCA9646D — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the PCA9646D when a legacy design needs a buffered, independently controlled four-output branch for an I2C-bus, SMBus, or PMBus network operating at up to 1 MHz. Its documented support for five 400 pF branches and impedance-isolated channels is especially useful when direct fan-out would create excessive bus loading. The PCA9546AD,112 is the closest documented candidate when its four-channel 16-pin SOIC implementation and control behavior satisfy the design, particularly when a basic multiplexer is sufficient rather than the PCA9646D's buffered branch architecture. For either part, review supply-voltage limits, logic thresholds, propagation delay, reset behavior, channel states, and control-register mapping. Because the PCA9646D is obsolete, a replacement decision should also include long-term availability, traceability, and qualification of any proposed substitute before production use.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە PCA9546AD,112
Brand NXP Semiconductors NXP Semiconductors
Package 16-pin SOIC 16-pin SOIC
Device Type Buffered 4-channel 2-wire bus switch I2C/SMBus interface IC
Channel Count 4 output channels 4 channels

جیاکەرەوە سەرەکییەکان

  • Buffered branch-oriented bus switching (بەراورد بەPCA9546AD,112)
  • Independent programming of every output branch (بەراورد بەPCA9546AD,112)
  • Higher documented operating frequency (بەراورد بەPCA9546AD,112)

تێبینییەکانی دیزاین

Treat each PCA9646D output as a separate branch and keep its route short and symmetric relative to the device pins. At the maximum 1 MHz operating frequency, the NXP datasheet specifies support for five 400 pF loads. Check the combined wiring, connector, and device capacitance rather than relying on the nominal bus frequency alone. Incorrect pull-up strength can produce slow rising edges or excessive ringing even when the branch count is acceptable.

Place pull-up resistors at the physical end of the relevant two-wire bus segment and provide an uninterrupted ground plane beneath the buffered paths. Avoid routing unrelated high-current or switching signals between the upstream bus and output branches, because the added coupling can reduce noise margin. When several PCA9646 devices are cascaded, preserve symmetric branch geometry and verify the combined propagation delay against the protocol timing budget.

Do not assume that a 16-pin SOIC footprint alone establishes drop-in compatibility with the PCA9546AD,112. The PCA9646D uses programmable channel enables and a buffered two-wire-switch architecture, so control logic, address behavior, timing, and electrical limits must be checked against both datasheets before substitution. Also confirm that unused channels are configured as intended rather than leaving an output state undefined during reset.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

No specific compliance declarations were stated in the available manufacturer or distributor product information.

داتا پشتڕاستکراوەتەوە لە: 2026-11-19 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

PCA9646D datasheet PCA9646D datasheet pdf PCA9646D pinout PCA9646D SOIC-16 PCA9646D 1 MHz PCA9646D 4 channel bus switch PCA9646D I2C bus buffer PCA9646D PMBus application PCA9646D equivalent PCA9646D replacement PCA9646D vs PCA9546AD,112 PCA9646D price PCA9646D stock NXP PCA9646D PCA9646D application circuit

پێکهاتە و زاراوە پەیوەندیدارەکان

NXP Semiconductors PCA9646D PCA9646 PCA9546AD,112 buffered 2-wire bus switch bus switch interface IC logic IC semiconductor I2C-bus SMBus PMBus two-wire bus 1 MHz bus speed four output channels impedance isolation programmable control register 400 pF bus capacitance 4 nF bus capacitance SOIC-16 SOIC package surface-mount package industrial temperature grade semiconductor
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ