PCA9646D - 4-Channel 1 MHz I2C Bus Buffer | NXP
MPN: PCA9646D ✗ پایان تولیدPCA9646D نمای کلی
A buffered 2-wire bus switch is an interface IC that regenerates bus signals while separating capacitive loads into independently controlled branches. In the hierarchy of semiconductor components, it belongs to the bus switch and interface-switch class, within logic and interface ICs. This differs from a basic multiplexer because the buffered outputs are designed to drive larger bus capacitance and maintain signal quality as branches are added.
The PCA9646D provides four independently enabled output channels, a maximum operating frequency of 1 MHz, and support for five branches when the input bus is included. The NXP datasheet states that the device can support up to five 400 pF loads for Fm+ I2C-bus operation at 1 MHz. At lower operating frequencies, the stated capability extends to five 4 nF loads. Every I/O is impedance-isolated from the others, helping prevent inactive branches from degrading signal integrity.
Control is performed through a programmable register, allowing any combination of the four outputs to be enabled. Multiple PCA9646 devices may also be cascaded when a system needs more segmented branches. This architecture is useful where bus capacitance, propagation delay, or branch loading would make a direct multi-device connection impractical. The device is designed for industrial-temperature operation from -40°C to +85°C and is supplied in a surface-mount 16-pin SOIC package.
Typical uses include isolating sensors on an I2C bus, connecting LED controllers to PMBus-compatible systems, partitioning SMBus devices, and supporting multi-branch industrial control boards. The four independently controlled outputs are especially useful when several devices share the same bus address or when a branch must be disconnected to prevent leakage from an inactive peripheral.
PCB design should preserve short, symmetric routing between the upstream bus and each output branch, while keeping ground returns continuous. The input and output nets must observe the capacitance limits stated in the manufacturer datasheet because longer branches or excessive loading can reduce rise time and cause communication errors even when the nominal clock is below 1 MHz.
This page consolidates the device architecture, operating limits, branch-loading capabilities, lifecycle information, and application guidance into a practical engineering reference for I2C-bus and SMBus buffer design.
جایگزینهای drop-in برای PCA9646D — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای PCA9646D (همان فرمفاکتور و فوتپرینت) — متفاوت در Package.
PCA9546AD,112
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PCA9646D مشخصات
| Product Type | Buffered 4-channel 2-wire bus switch |
| Number of Output Channels | 4 channels |
| Maximum Bus Frequency | 1 MHz |
| Total Supported Branches | 5 branches including the input branch |
| Maximum Fm+ I2C-Bus Loading at 1 MHz | 5 × 400 pF |
| Maximum Loading at Lower Frequencies | 5 × 4 nF |
| Process Technology | Monolithic CMOS |
| Output Control | 4 independently programmable outputs |
| Bus Compatibility | I2C-bus, SMBus, PMBus, and similar 2-wire systems |
| Branch Isolation | All I/O channels impedance-isolated |
| محدوده دمای کاری | -40°C to +85°C |
| بستهبندی | 16-pin SOIC, 3.90 mm body width |
| نوع نصب | Surface mount |
| Standard Packaging | Tape and reel |
راهنمای پیکربندی پین PCA9646D 16-pin soic, 3.90 mm body width
پیکربندی پین برای PCA9646D (پکیج 16-pin soic, 3.90 mm body width). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای PCA9646D.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
PCA9646D مناسب است برای 6 کاربردs: Industrial Sensor Bus Segmentation, PMBus Power Management Isolation, SMBus Equipment Isolation, Multi-Branch LED Control, Test and Measurement Fixture, Embedded Communication Port Isolation.
Industrial Sensor Bus Segmentation
The PCA9646D fits industrial sensor networks where several remote I2C devices create excessive capacitive loading on one bus segment. Place the device between the controller and four sensor branches, then use the programmable control register to enable only the populated branches. At 1 MHz, the NXP datasheet specifies support for five 400 pF loads, allowing the bus to remain segmented into controlled paths. The isolation between channels can reduce the effect of an unused or inactive sensor branch on signal rise time. Keep each branch physically short and verify that its total capacitance, pull-up resistance, and propagation delay remain within the system timing budget.
پیشنهادی
PMBus Power Management Isolation
The PCA9646D is appropriate for PMBus-based power systems in which several controllers, monitors, or converters must share a two-wire management bus. Its four independently enabled outputs can isolate power-management branches and prevent one heavily loaded peripheral from dominating the complete bus. The device supports PMBus and similar two-wire systems at rates up to 1 MHz, while the buffered outputs help preserve edge quality across segmented branches. Configure the control register for the required channel combination and use the NXP timing and capacitance limits as the basis for pull-up selection. This approach is especially helpful when converters are placed at different distances from the system controller.
پیشنهادی
SMBus Equipment Isolation
The PCA9646D can divide an SMBus network into independently managed branches for computer, storage, or industrial test equipment. Its four programmable outputs allow firmware to disconnect unused ports during boot, isolate a peripheral during recovery, or maintain communication with active devices when one branch is inactive. The buffered architecture operates up to 1 MHz, and the manufacturer specifies five 400 pF branch loads at that frequency. Designers should account for the added propagation delay of each buffer stage, select pull-ups for the worst branch capacitance, and avoid configuring the device as a general-purpose bidirectional multiplexer without reviewing the control logic in the datasheet.
پیشنهادی
Multi-Branch LED Control
The PCA9646D can support compact LED-control boards that distribute multiple lighting channels or drivers over a common two-wire control bus. Rather than attaching every LED controller directly to one long bus, the device provides four independently enabled outputs that partition the network and can leave unused driver branches isolated. This arrangement helps manage branch capacitance while retaining operation up to 1 MHz. The application benefits when LED controllers use compatible two-wire protocols and require selective startup. Use short, symmetric traces, confirm pull-up placement, and account for buffer propagation delay when timing dimming commands across multiple branches.
پیشنهادی
Test and Measurement Fixture
The PCA9646D is useful in test and measurement fixtures that connect several instruments, programmable components, or sensor adapters over a shared two-wire bus. Independent output enables let the fixture isolate unpopulated or faulted branches and reduce their influence on the active test path. With operation up to 1 MHz and support for five 400 pF loads at that rate, the device can organize higher-capacitance fixture wiring into controlled segments. The buffered outputs help maintain usable rise times when the master controller is located away from the test hardware. Validate the complete timing budget, including cable capacitance, connector parasitics, pull-up strength, and the additional delay introduced by the buffered switch.
پیشنهادی
Embedded Communication Port Isolation
The PCA9646D can isolate communication ports on embedded boards that serve several external sensors, memory devices, or interface adapters. Its four output channels may be enabled in any combination, allowing firmware to separate unused connectors and preserve a clean upstream bus during startup or fault recovery. This is particularly useful where cable-connected accessories add capacitance beyond the comfortable loading of a direct board bus. The NXP specification supports up to five 400 pF branches at 1 MHz, enabling a compact port-partitioning strategy. Check input and output rise-time limits, maintain a continuous return path, and confirm that the control interface does not conflict with other bus-management devices on the same board.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای PCA9646D — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | PCA9546AD,112 |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 16-pin SOIC | 16-pin SOIC |
| Device Type | Buffered 4-channel 2-wire bus switch | I2C/SMBus interface IC |
| Channel Count | 4 output channels | 4 channels |
تفاوتهای کلیدی
- Buffered branch-oriented bus switching (در مقابلPCA9546AD,112)
- Independent programming of every output branch (در مقابلPCA9546AD,112)
- Higher documented operating frequency (در مقابلPCA9546AD,112)
یادداشتهای طراحی
Treat each PCA9646D output as a separate branch and keep its route short and symmetric relative to the device pins. At the maximum 1 MHz operating frequency, the NXP datasheet specifies support for five 400 pF loads. Check the combined wiring, connector, and device capacitance rather than relying on the nominal bus frequency alone. Incorrect pull-up strength can produce slow rising edges or excessive ringing even when the branch count is acceptable.
Place pull-up resistors at the physical end of the relevant two-wire bus segment and provide an uninterrupted ground plane beneath the buffered paths. Avoid routing unrelated high-current or switching signals between the upstream bus and output branches, because the added coupling can reduce noise margin. When several PCA9646 devices are cascaded, preserve symmetric branch geometry and verify the combined propagation delay against the protocol timing budget.
Do not assume that a 16-pin SOIC footprint alone establishes drop-in compatibility with the PCA9546AD,112. The PCA9646D uses programmable channel enables and a buffered two-wire-switch architecture, so control logic, address behavior, timing, and electrical limits must be checked against both datasheets before substitution. Also confirm that unused channels are configured as intended rather than leaving an output state undefined during reset.
اطلاعات انطباق
No specific compliance declarations were stated in the available manufacturer or distributor product information.