PCF8574RGTR - 8-Bit I2C I/O Expander | Texas Instruments
MPN: PCF8574RGTR ✓ فعالPCF8574RGTR جائزہ
An I/O expander is an interface IC that extends the number of general-purpose input and output pins available to a microcontroller or system-on-chip. The PCF8574 belongs to the parallel I/O expander family within the interface IC hierarchy, connects to a host through I2C, and presents each remote port as a standard logic-level GPIO. Its compact package and interrupt output make it useful when a design lacks sufficient pins for switches, indicators, relays, or control inputs.
Key features include eight configurable I/O ports, operation from 2.5 V to 5.5 V, a 100 kHz I2C interface, three hardware address inputs, and an active-low open-drain interrupt output. The interface is compatible with both I2C and SMBus systems, while the small 3 mm by 3 mm VQFN footprint saves board area in space-constrained control boards. The manufacturer specifies an operating temperature range of -40 °C to +85 °C.
Each port can operate as an input or output and is designed for devices that source or sink modest logic-level current. The quasi-bidirectional architecture includes a weak output driver that can be actively pulled low or released for input detection. This arrangement works well with pull-up-based buses and typical digital peripherals, although firmware must account for the port's input and output drive characteristics when resolving multiple low-level signals.
Typical uses include expanding GPIO on an 8-bit microcontroller, driving LED indicators and key inputs in an industrial control panel, reading switch banks in an appliance, and supporting addressable bus nodes in embedded equipment. The interrupt pin can wake or notify the host when a port changes state, reducing the need for continuous polling when the application allows interrupt-driven I/O handling.
Place pull-up resistors on SDA and SCL according to the bus voltage and capacitance, and route the interrupt trace away from high-current switching nodes. Confirm that connected peripherals remain within the port's voltage, current, and timing limits. The exposed-pad package also requires a proper thermal and electrical ground connection under the device.
This page combines manufacturer specifications, package details, application guidance, and verified drop-in alternatives in a form useful for schematic capture, PCB layout, sourcing, and lifecycle review. It also highlights the differences between electrically similar expanders that use different port architectures.
کے لیے ڈراپ اِن متبادل PCF8574RGTR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PCF8574RGTR (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف RoHS Status, I2C Bus Frequency, Interface Type, Interrupt Output, Operating Temperature Range.
PCF8574RGTRG4
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PCA9534RGVR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PCA9534ARGVR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PCF8574RGTR
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PCF8574AT/3,518
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PCF8574RGTR تفصیلات
| Device Type | 8-bit I2C/SMBus input/output expander with interrupt |
| Number of I/O Ports | 8 ports |
| Number of Bits | 8 bits |
| Supply Voltage Range | 2.5 V to 5.5 V |
| I2C Bus Frequency | 100 kHz |
| Serial Interface | I2C/SMBus, two-wire bidirectional bus |
| Interrupt Output | Open-drain interrupt output |
| Address Inputs | 3 hardware address inputs |
| Port Architecture | Quasi-bidirectional input/output ports |
| آپریٹنگ درجہ حرارت رینج | -40 °C to +85 °C |
| پیکیج | 16-pin VQFN (RGT) |
| Package Dimensions | 3 mm x 3 mm |
| ماؤنٹنگ ٹائپ | Surface mount |
| Exposed Pad | Yes |
| MSL لیول | MSL 1 - 260 °C unlimited floor life |
| RoHS اسٹیٹس | RoHS3 compliant |
| Automotive Qualification | Not applicable |
| لائف سائیکل کی حالت | Active |
PCF8574RGTR پن کنفیگریشن
| پن 1 | INT — Open-drain interrupt output |
| پن 2 | SCL — Serial clock input for the I2C/SMBus interface |
| پن 3 | SDA — Bidirectional serial data for the I2C/SMBus interface |
| پن 4 | P0 — Quasi-bidirectional input/output port 0 |
| پن 5 | P1 — Quasi-bidirectional input/output port 1 |
| پن 6 | P2 — Quasi-bidirectional input/output port 2 |
| پن 7 | P3 — Quasi-bidirectional input/output port 3 |
| پن 8 | GND — Ground connection |
| پن 9 | P4 — Quasi-bidirectional input/output port 4 |
| پن 10 | P5 — Quasi-bidirectional input/output port 5 |
| پن 11 | P6 — Quasi-bidirectional input/output port 6 |
| پن 12 | P7 — Quasi-bidirectional input/output port 7 |
| پن 13 | VDD — Positive supply voltage input |
| پن 14 | A2 — Address input A2 |
| پن 15 | A1 — Address input A1 |
| پن 16 | A0 — Address input A0 |
عام استعمالات
PCF8574RGTR کے لیے موزوں ہے 6 ایپلیکیشنs: Microcontroller GPIO Expansion, Industrial Control Panel Interfaces, LED Status and Indicator Expansion, Appliance Keypad and Switch Interface, Remote Sensor and Discrete Input Hub, Communication Interface Auxiliary Node.
Microcontroller GPIO Expansion
The PCF8574RGTR is appropriate when a microcontroller has too few pins for a control panel, keypad, relay bank, or status display. Its eight ports operate from the same 2.5 V to 5.5 V supply range as many 3.3 V and 5 V controllers, while the 100 kHz I2C interface preserves the controller's other pins. This is particularly useful with small devices such as the ATTINY13A-SUR, where eight additional general-purpose lines can eliminate multiplexers and reduce routing complexity. Firmware should define each port as input or output, account for the quasi-bidirectional drive behavior, and use the interrupt line when polling overhead must be reduced.
تجویز کردہ
Industrial Control Panel Interfaces
A PCF8574RGTR can consolidate pushbuttons, selector switches, status lamps, and relay-control outputs into one compact I2C node. Its 16-pin 3 mm by 3 mm VQFN package leaves more board area available for power components and connectors than a larger 16-pin SOIC, while the -40 °C to +85 °C rating supports industrial-temperature environments. The open-drain interrupt output allows the controller to detect switch activity without continuously reading the bus. Use pull-up resistors appropriate to the bus voltage, and keep the compact footprint's exposed pad connected to the ground plane for both electrical and thermal performance.
تجویز کردہ
LED Status and Indicator Expansion
The eight quasi-bidirectional ports of the PCF8574RGTR can drive low-current LED indicators or control the enable inputs of upstream driver devices. A single 3.3 V I2C bus connection replaces several dedicated microcontroller pins, making the expander useful in display, instrument, and appliance controllers where panel space is limited. Because the ports include a weak output driver, high-current LEDs should use transistor or MOSFET drivers rather than being connected directly. Confirm the continuous sink-current limit of every driven output in the manufacturer datasheet, and test the selected resistor value against the intended brightness and supply voltage.
تجویز کردہ
Appliance Keypad and Switch Interface
The PCF8574RGTR is well suited to reading a matrix or bank of appliance controls while also driving a small number of status signals. Its three address inputs permit several expanders to share one I2C bus, and the interrupt output lets the appliance controller sleep between user actions. The 2.5 V minimum supply accommodates low-voltage control rails, while the 100 kHz bus rate provides ample bandwidth for short button reads. Because the device uses quasi-bidirectional ports, design the switch inputs with suitable pull-up or pull-down arrangements so every inactive line reaches a valid logic level.
تجویز کردہ
Remote Sensor and Discrete Input Hub
A PCF8574RGTR can act as a remote input hub for dry contacts, limit switches, interlocks, and other discrete signals distributed across a control board. Eight inputs share one I2C address, and the interrupt line provides a hardware indication that at least one input changed. This arrangement reduces the number of interconnects between a central controller and a peripheral board. Select pull-up or pull-down networks for reliable inactive-state levels, maintain separate return paths for noisy relays, and test debounce timing in firmware because mechanical contacts can generate multiple transitions during one physical event.
تجویز کردہ
Communication Interface Auxiliary Node
The PCF8574RGTR can supplement a communications processor that needs local control lines for modem, transceiver, or peripheral-enable functions. Its I2C interface allows auxiliary control logic to share the bus with transceivers such as the SP3232EUEY-L, avoiding dedicated GPIO pins on the main processor. The small VQFN package is advantageous in multi-function boards where connector placement limits available area. Address the auxiliary node through the A0, A1, and A2 straps, keep its interrupt trace away from switching edges, and confirm that every enabled peripheral has a defined state during controller reset and bus startup.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PCF8574RGTR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PCF8574RGTRG4 | PCA9534RGVR | PCA9534ARGVR | PCF8574A |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-VQFN (RGT) 3 mm x 3 mm | 16-VQFN (RGT) 3 mm x 3 mm | 16-VQFN (RGT) 3 mm x 3 mm | 16-VQFN (RGT) 3 mm x 3 mm | 16-VQFN (RGT) 3 mm x 3 mm |
| I/O Ports | 8 | 8 | 8 | 8 | 8 |
| Output Architecture | Quasi-bidirectional | Quasi-bidirectional | Push-pull | Push-pull | Quasi-bidirectional |
| Address Inputs | 3 | 3 | 3 | 3 | 3 |
| Interrupt Output | Open-drain interrupt | Open-drain interrupt | Open-drain interrupt | Open-drain interrupt | Open-drain interrupt |
اہم امتیازی خصوصیات
- Directly preserves the PCF8574 port behavior (بمقابلہPCA9534RGVR)
- Compact 16-pin footprint for space-constrained boards (بمقابلہPCF8574RGYR)
- Supports 3.3 V and 5 V systems over a 2.5 V to 5.5 V range (بمقابلہPCA9534RGVR)
- Three hardware address inputs support multi-node buses (بمقابلہPCF8574RGTRG4)
ڈیزائن نوٹس
Route SDA and SCL as short, matched traces away from switching nodes and relay-coil edges, and place their pull-up resistors close to the bus master. The PCF8574RGTR uses a 3 mm by 3 mm 16-pin VQFN footprint, so verify the land pattern and exposed-pad dimensions against the current manufacturer package drawing. Tie the exposed pad to the ground plane with short vias; do not leave it unconnected because the pad provides the package's principal thermal and electrical return path.
Calculate the I2C pull-up value from the bus voltage, total trace and component capacitance, and the 100 kHz maximum clock rate. Confirm the resulting rise time and sink current before layout release. The quasi-bidirectional port stage should be used mainly for inputs, conventional CMOS inputs, and modest logic-level loads; use external drivers for LEDs, relays, or other devices that exceed the port current capability. Firmware must also avoid relying on a port remaining strongly driven high when another device can pull it low.
Do not confuse PCF8574RGTR with PCF8574RGYR: both are in the same device family, but the latter uses a 20-VQFN 3.5 mm by 4.5 mm package and is not land-pattern-compatible. Likewise, verify output-drive behavior when considering a PCA9534-family substitution. Confirm the A0, A1, and A2 strap levels, define port input states during reset, and use the open-drain interrupt with an appropriate pull-up so the host can reliably detect asserted interrupts.
تعمیل کی معلومات
The component information identifies the PCF8574RGTR as RoHS3 compliant with MSL 1, 260 °C unlimited floor life. The REACH status is not established, and lead-free, halogen-free, and conflict-minerals declarations require manufacturer confirmation.