SN74LS540H - 8-Channel 5V 3-State Buffer | onsemi
MPN: SN74LS540H ✓ چالاکSN74LS540H گشتی
A logic buffer is a digital IC that strengthens a signal for reliable propagation through a circuit or board. The SN74LS540 belongs to the bipolar TTL family and occupies the hierarchy digital IC > logic IC > buffer/line driver. Its inverting channels complement the 74LS541 non-inverting function, while its three-state outputs add bus isolation that a conventional two-state buffer cannot provide.
The device contains eight inverters and one common active-low output enable. According to the Texas Instruments SN74LS540 datasheet SDLS180, the circuit has input and output pins placed on opposite sides of the package, simplifying routing and reducing signal-bus congestion. Its 4.75 V to 5.25 V operating range is characteristic of 5 V bipolar TTL systems, where it is intended to operate from a regulated 5 V supply.
The three-state output stage is the key technical feature. When the output-enable input is low, all eight outputs are actively driven in their inverted logic state. When it is high, the outputs enter the high-impedance state and cease driving the connected bus. The 74LS540 has no individual enable input for each channel; all eight outputs are controlled together, making it appropriate for coordinated eight-bit bus isolation.
Typical uses include bus-interface buffering, digital test equipment, computer peripheral interfacing, and data-routing systems that require inverted data and shared-bus control. The 20-pin DIP package is also useful for prototypes, legacy industrial equipment, and repair assemblies designed around through-hole logic boards. Designers should still verify the exact mechanical dimensions and pin numbering of the onsemi orderable variant before fabrication.
When laying out the circuit, place the shared output-enable trace away from high-speed data paths and use a defined logic level whenever the enable pin is not actively controlled. Maintain a stable 5 V rail with sufficient decoupling, and treat the high-impedance outputs as undriven buses rather than outputs that actively produce a logic zero or one. This distinction is essential when receivers remain connected while the SN74LS540H is disabled.
This product record combines the device function, electrical limits, pin assignment, source documentation, practical application guidance, and same-footprint replacement analysis. It is intended to help engineers distinguish a genuine pin-compatible replacement from a functional substitute that changes the package, enable polarity, logic family, or output behavior.
جێگرەوەکانی جێگۆڕکێ بۆ SN74LS540H — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ SN74LS540H (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package.
SN74LS540N
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →SN74LS540J
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
SN74LS540N
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →74LS540
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
DM74LS540
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
SN74LS540H زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | Octal inverting buffer/line driver with 3-state outputs |
| Number of Channels | 8 channels |
| Bits per Channel | 1 bit per channel |
| ڕێکخستنی دەرچوون | 3-state, inverting |
| Operating Supply Voltage Range | 4.75 V to 5.25 V |
| Logic Technology | Bipolar TTL |
| Output Enable Polarity | Active-low, common control for all channels |
| Number of Output Enable Inputs | 1 common output-enable input |
| پاکێج | DIP-20 |
| ژمارەی پین | 20 pins |
| جۆری دامەزراندن | Through-hole |
| Input and Output Pin Arrangement | Inputs and outputs on opposite sides of the package |
ڕێکخستنی پینی SN74LS540H
| پین 1 | 1A — Data input for channel 1 |
| پین 2 | 2A — Data input for channel 2 |
| پین 3 | 3A — Data input for channel 3 |
| پین 4 | 4A — Data input for channel 4 |
| پین 5 | 5A — Data input for channel 5 |
| پین 6 | 6A — Data input for channel 6 |
| پین 7 | 7A — Data input for channel 7 |
| پین 8 | 8A — Data input for channel 8 |
| پین 9 | GND — Ground reference |
| پین 10 | 1OE — Common active-low output enable |
| پین 11 | 8Y — Inverting output for channel 8 |
| پین 12 | 7Y — Inverting output for channel 7 |
| پین 13 | 6Y — Inverting output for channel 6 |
| پین 14 | 5Y — Inverting output for channel 5 |
| پین 15 | 4Y — Inverting output for channel 4 |
| پین 16 | 3Y — Inverting output for channel 3 |
| پین 17 | 2Y — Inverting output for channel 2 |
| پین 18 | 1Y — Inverting output for channel 1 |
| پین 19 | VCC — Positive power supply |
| پین 20 | NC — Not connected |
بەکارهێنانە باوەکان
SN74LS540H گونجاوە بۆ 6 بەکارھێنانs: Shared Digital Data Bus, Legacy Industrial Control Interface, Computer Peripheral Data Interface, Digital Test and Measurement Equipment, Instrumentation Signal Routing, Prototyping and Legacy Logic Repair.
Shared Digital Data Bus
The SN74LS540H fits shared eight-bit bus buffering because all eight outputs can be disabled together through the common active-low output-enable input. In the enabled state, the device actively drives inverted data across the 4.75 V to 5.25 V supply range; in the disabled state, its outputs become high-impedance and release the bus. This arrangement helps prevent two buffers from driving the same net simultaneously when system timing coordinates the enable interval. Because the logic is inverting and the enable control is shared, downstream circuitry must account for both inversion and common switching. The 20-pin DIP package is particularly practical for legacy boards, test fixtures, and industrial control systems that use through-hole logic.
پێشنیارکراو
Legacy Industrial Control Interface
SN74LS540H is useful as an interface-conditioning element between older bipolar TTL control logic and a modern peripheral or data-acquisition module. Its eight inverting channels provide signal buffering, while the shared 3-state control can isolate the interface from a shared wiring harness during another subsystem's transfer cycle. Operating from 4.75 V to 5.25 V matches regulated 5 V industrial logic systems and supports point-to-point or shared-bus routing. Designers should use a single defined output-enable level when no controller is connected, preserve adequate supply decoupling, and verify timing margins because the device introduces the propagation delay specified by the SN74LS540 family datasheet.
پێشنیارکراو
Computer Peripheral Data Interface
The SN74LS540H can condition eight parallel data lines between a computer peripheral and an external bus. Its common three-state control lets the interface release all eight lines when the peripheral is not selected, reducing bus contention during transfers to another device. The 74LS540 architecture places inputs and outputs on opposite sides of the package, which can simplify through-hole board routing compared with interleaved input and output pins. Because the channels invert the incoming data, the receiving endpoint must use the expected inverted logic level or include an additional inversion stage. A suitable system design must also confirm voltage compatibility, timing, and the electrical-current requirements of the connected receiver.
پێشنیارکراو
Digital Test and Measurement Equipment
SN74LS540H is appropriate for legacy digital test equipment that needs an eight-line inverting buffer with a shared disable control. The active-low enable can be driven by a fixture controller so that the device drives its test lines during one phase and releases them during another. That controlled high-impedance interval is useful when the same fixture lines connect to multiple DUTs or measurement circuits. Its 20-pin DIP construction supports through-hole prototyping and repair of older instrumentation. Engineers should account for data inversion, account for the common enable rather than assuming eight independent controls, and check fanout and settling requirements against the source and load devices connected to the fixture.
پێشنیارکراو
Instrumentation Signal Routing
The SN74LS540H can serve as a digital control-line buffer in instrumentation that routes commands to multiple subsystems. Eight related logic signals are inverted in a controlled manner and then either drive their loads or enter the high-impedance state, depending on the common output-enable level. This can prevent inactive interface logic from loading a shared control bus. The function is most suitable for digital control and status signals rather than high-speed analog instrumentation, and timing analysis should compare the propagation delay with the system setup and hold requirements. Because the package uses a 20-pin DIP footprint, it also suits older repair platforms where adding a new surface-mount footprint would be impractical.
پێشنیارکراو
Prototyping and Legacy Logic Repair
SN74LS540H is well suited to prototyping and repair of through-hole digital logic boards that call for eight buffered, inverted, three-state lines. The DIP-20 package permits straightforward socketed assembly and replacement of an existing 74LS540-family device after pin and construction checks. Its shared output-enable behavior makes it useful for isolating a failed subsystem from a common bus during diagnosis. When fitting the part, verify that the target board expects an active-low enable and eight inverting channels rather than the non-inverting SN74LS541 function. Also confirm supply tolerance, operating-temperature requirements, and whether the original assembly specifically required a hermetic package before treating a plastic or manufacturer-alternate DIP as equivalent.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ SN74LS540H — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | SN74LS540N | SN74LS540J | SN74LS540N | 74LS540 | DM74LS540 |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments | Motorola, Inc | onsemi |
| Package | DIP-20 | DIP-20 | DIP-20 | DIP-20 | DIP-20 | DIP-20 |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Logic Function | Octal inverting buffer/line driver | Octal inverting buffer/line driver | Octal inverting buffer/line driver | Octal inverting buffer/line driver | Octal inverting buffer/line driver | Octal inverting buffer/line driver |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state | 3-state |
| Operating Supply Voltage Range | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Output Enable | One common active-low output enable | One common active-low output enable | One common active-low output enable | One common active-low output enable | One common active-low output enable | One common active-low output enable |
| Logic Technology | Bipolar TTL | Bipolar TTL | Bipolar TTL | Bipolar TTL | Bipolar TTL | Bipolar TTL |
| Input/Output Pin Arrangement | Inputs and outputs on opposite package sides | Inputs and outputs on opposite package sides | Inputs and outputs on opposite package sides | Inputs and outputs on opposite package sides | Inputs and outputs on opposite package sides | Inputs and outputs on opposite package sides |
جیاکەرەوە سەرەکییەکان
- Common 3-state control for all eight channels (بەراورد بەSN74LS244N)
- Opposite-side input and output arrangement (بەراورد بەSN74LS240N)
- Inverting octal logic retains standard 74LS540 behavior (بەراورد بەSN74LS541N)
تێبینییەکانی دیزاین
Do not treat the high-impedance output state as a driven logic level. When the common active-low output-enable input is high, SN74LS540H releases all eight outputs, and external pull-up or pull-down components determine the voltage seen by connected receivers if the bus is otherwise floating. Confirm that the system intentionally permits this condition. Also verify inversion at the receiver, because every enabled channel reverses the input logic state.
Follow the DIP-20 pin arrangement in datasheet SDLS180 and keep the eight data inputs on one side of the package and the eight outputs on the other. Place the device close to the connector or bus being buffered, and keep the common output-enable trace away from sensitive analog or high-speed timing paths. Provide a low-impedance ground reference and use a solid ground plane rather than routing return current through narrow signal traces.
Analyze setup, hold, propagation delay, fanout, and rise/fall-time requirements before using SN74LS540H in a high-speed bus. The bipolar TTL output stages are intended for conventional 5 V logic systems, so long PCB traces, heavily capacitive loads, or repeated fanout branches may reduce timing margin. Keep the shared enable synchronized with the bus source-selection logic and avoid enabling the device while another driver remains active on the same nets.
زانیاری پابەندبوون
Compliance declarations were not identified for the exact onsemi SN74LS540H orderable MPN. AEC-Q100 status is not applicable because this is a general-purpose bipolar logic IC rather than an automotive-qualified device.