TJA1022T - Dual LIN 2.2A Transceiver | NXP Semiconductors
MPN: TJA1022T ✓ چالاکTJA1022T گشتی
A LIN transceiver is a physical-layer interface IC within the broader automotive networking hierarchy. It connects a host microcontroller or LIN protocol controller to a low-speed, single-wire vehicle network by translating controller-side logic signals into LIN bus levels and receiving bus signals for the controller. Two integrated transceivers allow one controller to manage two LIN channels while retaining a common device footprint and application architecture.
The TJA1022 is primarily intended for in-vehicle subnetworks operating at baud rates up to 20 kBd. Its stated compliance includes LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602. These protocol and automotive-interface specifications make the TJA1022T relevant to distributed vehicle systems in which body, comfort, lighting, seat, door, and other accessory modules exchange commands and diagnostic information over LIN networks.
The NXP datasheet identifies the TJA1022T and TJA1022TK as pin-compatible with the TJA1020, TJA1021, TJA1027, and TJA1029. It also states that the TJA1022, TJA1024, TJA1027, and TJA1029 are software compatible. These compatibility statements support platform reuse, although designers should still verify operating conditions, enabled features, electrical limits, and package dimensions for each selected order code before treating a part as a replacement.
Typical uses include vehicle body-control modules, door and seat controllers, lighting controllers, climate-control interfaces, sensor nodes, and gateway modules that combine LIN communication with microcontroller processing. The dual-channel configuration can simplify boards that must connect multiple LIN subnets while reducing the number of separate physical-layer transceivers required.
When designing around the TJA1022T, preserve the pin compatibility and protocol expectations of the selected TJA1020, TJA1021, TJA1027, or TJA1029 reference design. The LIN bus interface must be reviewed against the manufacturer datasheet for termination, wiring, protection, grounding, and application-specific guidance. This page combines verified manufacturer information, distributor availability, package details, and compatibility options for faster component selection.
This product data adds practical context beyond basic catalog listings by organizing protocol compliance, package compatibility, verified alternative families, bus-focused applications, and sourcing information. It highlights where the TJA1022T fits in a LIN network while clearly separating verified facts from specifications that still require confirmation from the manufacturer datasheet.
جێگرەوەکانی جێگۆڕکێ بۆ TJA1022T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ TJA1022T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Maximum Baud Rate, Pin Compatibility.
TJA1020T
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TJA1021T/20/C
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →TJA1027T
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TJA1029T/2Z
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →TJA1022T تایبەتمەندییەکان
| Product Type | Dual LIN transceiver |
| LIN Channels | 2 channels |
| Maximum LIN Baud Rate | 20 kBd |
| LIN 2.0 Compliance | Compliant |
| LIN 2.1 Compliance | Compliant |
| LIN 2.2 Compliance | Compliant |
| LIN 2.2A Compliance | Compliant |
| SAE J2602 Compliance | Compliant |
| پاکێج | SO14 |
| جۆری دامەزراندن | Surface mount |
ڕێنمایی ڕێکخستنی پینی TJA1022T so14
ڕێکخستنی پین بۆ TJA1022T (پاکێجی so14). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ TJA1022T.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
TJA1022T گونجاوە بۆ 6 بەکارھێنانs: Vehicle Body Control Module, Door and Accessory Control, Automotive Lighting Controller, Climate Control Subnetwork Interface, Automotive Sensor Node, LIN Gateway and Communication Hub.
Vehicle Body Control Module
The TJA1022T fits body-control modules that connect distributed door, lighting, seat, and accessory modules to a host microcontroller. Its two LIN transceivers support vehicle subnetworks at rates up to 20 kBd, while stated compliance with LIN 2.0 through LIN 2.2A and SAE J2602 provides a documented protocol baseline. Placing both physical-layer interfaces in one SO14 device can simplify routing and component selection compared with using separate single-channel transceivers. The controller still needs matching LIN protocol handling, and the final design must verify power, grounding, protection, and bus-integration details against the NXP datasheet.
پێشنیارکراو
Door and Accessory Control
The TJA1022T is suitable for door-zone controllers, latch modules, window controls, and seat-position nodes connected through a LIN subnet. The documented maximum rate of 20 kBd matches the intended low-speed in-vehicle environment, while two channels can serve nodes that need separate LIN connections. Compatibility with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602 supports protocol-oriented platform design. Engineers should use the manufacturer datasheet to confirm bus loading, mode-control behavior, supply limits, and pin-level implementation before approving a drop-in replacement.
پێشنیارکراو
Automotive Lighting Controller
A lighting-control module can use the TJA1022T when exterior or interior lamps are distributed over a LIN subnet rather than wired directly to the main controller. The device provides two LIN physical-layer channels, each operating within the family's stated 20 kBd capability, and its listed LIN and SAE J2602 compliance supports standardized in-vehicle communication. The dual-channel arrangement may reduce board area and simplify firmware resource allocation. Lamp drivers and diagnostics remain separate functions, so the LIN interface should be evaluated for bus termination, fault behavior, wake-up strategy, and environmental requirements.
پێشنیارکراو
Climate Control Subnetwork Interface
The TJA1022T can provide the physical interface for climate-control subsystems that distribute sensor, actuator, or panel commands over LIN. A 20 kBd dual-transceiver device aligns with the low-bandwidth, cost-conscious vehicle subnetwork architecture described by NXP. Using one controller with two LIN channels can support separate HVAC and cabin-conditioning subnetworks while preserving a common component footprint. The implementation should account for the number of nodes, bus capacitance, wake-up and sleep requirements, and any protection network required by the vehicle platform.
پێشنیارکراو
Automotive Sensor Node
Compact sensor nodes can use the TJA1022T as the LIN physical-layer interface when the node must exchange measurements or configuration data with a vehicle network. The stated support for LIN 2.2A and SAE J2602 provides relevant protocol context, while the dual-channel architecture offers flexibility where a node serves more than one LIN connection. A low-speed LIN bus helps integrate distributed sensing without requiring a more complex communications physical layer. The exact supply range, standby current, bus-output capability, and environmental limits must be taken from the complete NXP datasheet before schematic sign-off.
پێشنیارکراو
LIN Gateway and Communication Hub
The TJA1022T can support a communication hub that bridges a host controller to two independent LIN subnetworks. Its dual-transceiver arrangement is useful when the gateway needs separate bus connections without duplicating the physical-layer component footprint. The 20 kBd maximum rate is consistent with the LIN networks targeted by the manufacturer, and compliance across several LIN revisions supports use in established vehicle platforms. Gateway designs still require independent bus management, termination strategy, fault containment, and software scheduling; physical-layer compatibility alone does not provide protocol routing or arbitration.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ TJA1022T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | TJA1020T | TJA1021T | TJA1027T | TJA1029T |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SO14 | SO14 | SO14 | SO14 | SO14 |
| Pin Compatibility with TJA1022 | Reference device | Pin compatible | Pin compatible | Pin compatible | Pin compatible |
جیاکەرەوە سەرەکییەکان
- Dual-channel integration in one package (بەراورد بەTJA1020T)
- Documented support for LIN 2.2A and SAE J2602 (بەراورد بەTJA1020T)
- Software-compatible LIN platform option (بەراورد بەTJA1029T)
تێبینییەکانی دیزاین
Use the NXP TJA1022 datasheet land pattern for the SO14 footprint and confirm every pin function before routing the PCB. The verified compatibility statement covers TJA1020, TJA1021, TJA1027, and TJA1029, but it does not establish that every alternative exposes identical mode-control or sleep behavior. Preserve the manufacturer-recommended decoupling placement and keep the LIN interface away from high-current switching nodes to reduce coupled disturbance.
Do not treat pin compatibility or software compatibility as proof that two LIN devices are interchangeable in every operating condition. Before substituting TJA1020T, TJA1021T, TJA1027T, or TJA1029T, compare supply voltage, bus-output current, dominant-state and sleep behavior, wake-up logic, temperature range, qualification, and error handling. This is especially important in modules that share one PCB across several vehicle configurations.
Follow the NXP application guidance for LIN bus wiring, termination, grounding, and protection. A LIN bus is sensitive to network topology and parasitic capacitance, so the selected transceiver must be evaluated with the intended number of nodes, cable lengths, and vehicle harness conditions. Validate signal integrity and fault recovery at the system level rather than relying only on the stated 20 kBd maximum baud rate.
Verify the transceiver supply range and current consumption from the manufacturer datasheet because these values were not exposed in the supplied web results. Account for the supply current of both integrated channels and any local logic when sizing the regulator and decoupling network. Also evaluate the module's sleep and wake architecture, since a communication transceiver can materially influence total standby power even when the host controller is inactive.
زانیاری پابەندبوون
The verified NXP product information confirms LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, and SAE J2602 compliance, but the supplied web snippets do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These values remain unknown rather than being inferred.