TJA1040T/H/V - 1 Mbps CAN Transceiver | NXP Semiconductors
MPN: TJA1040T/H/V ✗ کۆتایی ژیانTJA1040T/H/V گشتی
A CAN transceiver is an interface IC that connects a CAN protocol controller to the physical bus. The TJA1040T/H/V belongs to the CAN transceiver class, also described as a CAN physical-layer interface, interface IC, and CAN bus transceiver. It supports the differential signaling used by high-speed CAN systems, allowing controller-side TXD and RXD signals to interface with the CANH and CANL bus conductors.
The principal device characteristics include a maximum intended CAN data rate of 1 MBaud, a half-duplex CAN transceiver arrangement, differential transmit capability, and differential receive capability. The 8-SO package supports conventional surface-mount PCB assembly. The TJA1040 family is intended for automotive and other CAN-based passenger-car applications where the physical-layer transceiver must operate alongside a separate CAN protocol controller.
The transceiver architecture separates protocol processing from bus-line interfacing: the CAN controller generates and interprets frames, while the TJA1040T/H/V handles the electrical signaling between logic-level pins and the CAN bus. This division allows the controller to manage arbitration, acknowledgment, error handling, and higher-layer communication independently of the physical-layer conversion performed by the transceiver.
Typical applications include automotive electronic control units, body-control modules, powertrain controllers, gateway modules, engine controllers, and other distributed vehicle systems. The same high-speed CAN physical interface can also be used in industrial, robotics, and transportation equipment when the system uses a compatible CAN controller and bus topology.
Designers should verify the device pinout, supply requirements, CANH and CANL connections, termination strategy, and the exact ordering-code interpretation in the manufacturer datasheet before layout release. For PCB work, use the SOIC-8 land pattern and route the differential bus pair with consistent geometry and symmetry. The CAN bus should be properly terminated at the physical ends of the network, and the power and ground connections should follow the datasheet recommendations.
This page combines the NXP product description, manufacturer data-sheet reference, cross-reference findings, package information, practical application guidance, and structured comparisons for engineers evaluating the TJA1040T/H/V in a high-speed CAN design.
جێگرەوەکانی جێگۆڕکێ بۆ TJA1040T/H/V — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
TJA1040T/H/V,118
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TJA1040T/CM,118
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TJA1040T/H/V,518
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
SN65HVD1040A
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
SN65HVD1040A-Q1
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TJA1040T/H/V تایبەتمەندییەکان
| Product Type | High-speed CAN physical-layer transceiver |
| Maximum Intended Data Rate | 1 MBaud |
| Transceiver Configuration | 1/1 half-duplex CAN transceiver |
| Transmit Capability | Differential |
| Receive Capability | Differential |
| پاکێج | 8-SO |
| Package Type | SOIC-8 surface-mount package |
| ژمارەی پینەکان | 8 pins |
| Bus Interface | CANH and CANL differential bus |
| Controller Interface | TXD and RXD logic-level interface |
| Primary Application | Passenger-car high-speed CAN networks |
| Product Category | Interface IC / CAN transceiver |
ڕێکخستنی پینی TJA1040T/H/V
| پین 1 | TXD — Transmit data input from the CAN controller |
| پین 2 | GND — Ground connection |
| پین 3 | VCC — Transceiver supply connection |
| پین 4 | RXD — Receive data output to the CAN controller |
| پین 5 | VIO — Input and output logic-level supply connection |
| پین 6 | CANL — CAN low bus line |
| پین 7 | CANH — CAN high bus line |
| پین 8 | NC — Not connected |
بەکارهێنانە باوەکان
TJA1040T/H/V گونجاوە بۆ 6 بەکارھێنانs: Automotive Body Control Module, Engine Control Unit, Vehicle Gateway Module, Industrial CAN Controller Card, Robotics Communication Module, Transportation and Rail Equipment.
Automotive Body Control Module
The TJA1040T/H/V fits a body-control module because it provides the physical interface between a CAN controller and the vehicle's 1 MBaud CAN bus. Its differential transmitter and receiver allow logic-level controller signals to reach CANH and CANL while rejecting common-mode noise through differential reception. The 8-SO package also fits the compact layouts common in distributed vehicle electronics. During PCB design, route the differential bus pair symmetrically, place protection and termination components according to the board topology, and verify the transceiver's exact supply and temperature ratings for the vehicle environment.
پێشنیارکراو
Engine Control Unit
An engine control unit can use the TJA1040T/H/V to connect its CAN protocol controller to a high-speed vehicle network operating up to 1 MBaud. The transceiver handles the differential electrical interface while the controller manages frames, diagnostics, and arbitration. That separation is useful in powertrain electronics where deterministic communication and robust differential signaling are required. Layout should keep CANH and CANL away from ignition and motor-drive switching paths, and the finished design should be checked for bus fault, supply, and temperature behavior against the manufacturer data sheet.
پێشنیارکراو
Vehicle Gateway Module
The TJA1040T/H/V is appropriate for a gateway module that connects a CAN protocol controller to a high-speed CAN network segment. Its differential receive path supports communication with multiple nodes, while differential transmission drives the physical bus. In a gateway PCB, the 8-SO footprint simplifies assembly, but signal-integrity work remains important: preserve a symmetric CANH/CANL pair, provide a solid ground reference, apply protection close to external connectors, and place bus-splitting or termination components only where the network architecture requires them.
پێشنیارکراو
Industrial CAN Controller Card
The TJA1040T/H/V can serve as the physical-layer element of an industrial CAN controller card connected to equipment operating at up to 1 MBaud. It lets a host controller use TXD and RXD logic signals while the transceiver connects to the differential CAN bus. The part is useful when a legacy control architecture must preserve the established TJA1040 electrical interface. For industrial deployment, verify the exact suffix's environmental limits, provide filtering at cable-entry points, maintain a controlled reference plane, and avoid long unprotected stubs that could disturb bus timing or fault behavior.
پێشنیارکراو
Robotics Communication Module
A robot communication module can use the TJA1040T/H/V to bridge a CAN controller and a high-speed CAN network used for sensors, actuators, and distributed controllers. Differential signaling is useful in machinery environments where cable length and common-mode disturbances can affect communication. The 8-SO package supports compact controller-board placement, while the transceiver handles only the physical layer. Designers should maintain controlled bus topology, use termination at the two physical endpoints, keep CAN wiring away from motor and relay paths, and validate timing with the actual cable and loading configuration.
پێشنیارکراو
Transportation and Rail Equipment
The TJA1040T/H/V can support CAN-based communication in transportation equipment where the system architecture uses a compatible high-speed CAN controller and bus. Its 1 MBaud capability and differential bus interface provide a defined physical-layer function for distributed nodes. The choice must account for the exact device grade, environmental limits, and current availability because lifecycle status affects long-term support. PCB implementations should use a controlled CANH/CANL pair, provide connector-side protection, maintain uninterrupted ground returns, and verify operation across the full vehicle supply and temperature range.
پێشنیارکراو
داتای سەرچاوەی ئەندازیاری بۆ TJA1040T/H/V — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | TJA1040T/H/V,118 | TJA1040T/CM,118 | TJA1040T/H/V,518 | SN65HVD1040A | SN65HVD1040A-Q1 |
|---|---|---|---|---|---|---|
| Package | SOIC-8 (8-SO) | SOIC-8 (8-SO) | SOIC-8 (8-SO) | SOIC-8 (8-SO) | SOIC-8 | SOIC-8 |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Texas Instruments | Texas Instruments |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | CAN transceiver | Automotive CAN transceiver |
| Number of Pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins |
جیاکەرەوە سەرەکییەکان
- Established NXP high-speed CAN physical-layer interface (بەراورد بەSN65HVD1040A)
- Direct same-brand ordering compatibility (بەراورد بەTJA1040T/H/V,518)
- Documented pin-level replacement path with enhanced ESD protection (بەراورد بەTJA1040T/H/V)
تێبینییەکانی دیزاین
Route CANH and CANL as a symmetrical differential pair with continuous reference to the ground plane. Use the PCB stack-up to establish a controlled impedance, avoid discontinuities, and keep the pair away from switching-power and high-current return paths. Place transceiver bypass capacitance close to the relevant supply pins and follow the NXP data sheet's layout guidance when establishing the ground and supply connections.
Do not assume that every 8-pin CAN transceiver is pin-compatible. The TJA1040T/H/V uses a specific controller, supply, and bus pin arrangement, and the SN65HVD1040A family has documented timing and ESD-related distinctions. Confirm the footprint and pin table, verify VIO and supply thresholds, and review dominant-timeout behavior before substituting a part in an operating vehicle or industrial network.
Place the CAN connector, protection network, termination components, and transceiver in a deliberate signal path. Protection devices should be close to the connector, while the CANH/CANL pair should proceed to the transceiver with minimal stubs and consistent geometry. Install termination only at the physical ends of the CAN network because excess parallel termination can alter bus loading and degrade communication margin.
Treat the TJA1040T/H/V ordering suffix as a controlled part of the design identity. The TJA1040T/H/V, TJA1040T/H/V,118, and TJA1040T/H/V,518 references can describe related ordering or delivery configurations rather than interchangeable engineering choices. Verify package drawing, temperature grade, qualification, and lifecycle for the exact production suffix instead of substituting suffixes solely from their visual similarity.
زانیاری پابەندبوون
The exact-suffix environmental and compliance attributes are not stated in the accessible product references and must be confirmed with NXP before production release.