TJA1128HTK/0Z LIN SBC with 85 mA LDO, 14-HVSON | NXP
MPN: TJA1128HTK/0Z ✓ چالاکTJA1128HTK/0Z گشتی
A system basis chip sits between a microcontroller and the rest of an automotive electrical system, bundling the power conversion, bus interface and supervision functions that a node needs to talk to the vehicle network and to the outside world. In the hierarchy of automotive electronics, the TJA1128 is a LIN transceiver integrated into an SBC, which itself is a power-management and communication IC rather than a discrete transceiver. The TJA1128 also carries AEC-Q100 automotive qualification, so it is intended for harsh in-vehicle conditions rather than for consumer equipment.
Key features include an integrated LDO capable of delivering up to 85 mA, available in 3.3 V and 5.0 V output versions, which removes the need for a separate regulator for small-signal sensor and logic nodes. The chip adds a window watchdog for host supervision, two wake inputs so the node can be brought out of sleep by external activity, a general purpose input for discrete switch sensing, and an HVMPO output capable of driving higher-current loads than a standard GPIO. The LIN transceiver is a 1/1 half-duplex implementation, matching the single-wire LIN physical layer.
Architecturally, the device splits its supply into a battery-connected high-voltage domain for the LIN bus and wake detection and a regulated domain for the logic and microcontroller interface. That split lets the node remain operable while the host microcontroller is held in reset or power-down, which is the basis of the very low power operating modes described in the NXP TJA1128 datasheet.
Typical applications include LIN sub-networks in body control modules, seat and door modules, smart junction boxes, ambient lighting controllers, LIN sensor nodes such as seat-occupancy or ambient sensors, and compact battery-backed telematics units where a single component must handle bus communication, regulation and host supervision.
When designing around this part, budget the LDO current carefully: the 85 mA rating covers the transceiver, the local microcontroller and attached sensors, but not motors or lamps. Confirm headroom for the host supply so the regulator does not enter thermal or current limiting during load transients, and review the window-watcher timing in the datasheet against your host refresh cycle.
This page brings together the manufacturer datasheet detail, package and pin information, drop-in alternatives and practical design notes so that an engineer can qualify the TJA1128HTK/0Z for a LIN node without chasing several documents.
جێگرەوەکانی جێگۆڕکێ بۆ TJA1128HTK/0Z — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ TJA1128HTK/0Z (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Automotive Qualification, High-Voltage Multipurpose Output, Automotive Application.
TJA1128FTK/0Z
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →TJA1145ATK/FD/0Z
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TJA1128HTK/0Z تایبەتمەندییەکان
| Product Type | LIN Mini System Basis Chip (SBC) |
| Integrated Functions | LIN transceiver + LDO + window watchdog + 2 WAKE inputs + 1 GPI + 1 HVMPO output |
| LIN Transceiver Type | 1/1 half-duplex LIN transceiver |
| Integrated LDO Output Current | 85 mA |
| LDO Output Voltage Options | 3.3 V or 5.0 V |
| Regulator Topology | Low-dropout regulator (LDO) |
| Watchdog | Window watchdog with two WAKE inputs |
| General Purpose Inputs | 1 GPI |
| High-Voltage Multipurpose Output | 1 HVMPO output |
| پاکێج | 14-HVSON (3 x 4.5 mm) |
| ژمارەی پین | 14 pins |
| جۆری دامەزراندن | Surface mount |
| Automotive Qualification | AEC-Q100 qualified |
| Low Power Modes | Very low power operating modes, sleep wake-up from external activity |
ڕێنمایی ڕێکخستنی پینی TJA1128HTK/0Z 14-hvson (3 x 4.5 mm)
ڕێکخستنی پین بۆ TJA1128HTK/0Z (پاکێجی 14-hvson (3 x 4.5 mm)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ TJA1128HTK/0Z.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
TJA1128HTK/0Z گونجاوە بۆ 6 بەکارھێنانs: LIN Body Control Module Node, Smart Junction Box and Ambient Lighting Controller, Seat and Door Control Module, Low-Power LIN Sensor Node, LIN Cluster and HMI Back-End Interface, Battery-Backed Telematics Unit.
LIN Body Control Module Node
The TJA1128HTK/0Z is well matched to a LIN sub-network node inside a body control module, where a single low-cost MCU needs to talk to switches, door modules and seat sensors over one wire. The integrated 85 mA LDO supplies the microcontroller and its signal conditioning without a separate regulator, while the 1/1 half-duplex LIN transceiver handles the physical layer. The window watchdog supervises the host refresh cycle, and the two wake inputs let a node be brought out of sleep by a change on a switch or an activity on the bus. The 14-HVSON (3 x 4.5 mm) footprint keeps board area low in densely packed central electronics. Keep total board load within 85 mA and use the HVMPO output for loads above GPIO current capability.
پێشنیارکراو
Smart Junction Box and Ambient Lighting Controller
In a smart junction box the TJA1128HTK/0Z consolidates bus communication, supply regulation and control into one device. A LIN-driven ambient lighting strip typically needs a regulated rail for its controller electronics plus a switch capable of driving LED current, which is exactly the split the part provides: an 85 mA LDO for control logic and a high-voltage multipurpose output for higher-current switching. The general purpose input can monitor a door- or position-triggered switch, and the window watchdog resets the MCU if it stops refreshing, protecting the lighting state. Because the HVMPO output is intended for automotive loads rather than high-current LED strings, pair it with a proper high-side driver for dense LED arrays.
پێشنیارکراو
Seat and Door Control Module
Seat and door modules sit at the end of short LIN branches where reliability and standby current matter more than raw speed. The TJA1128HTK/0Z offers a window watchdog to protect the module against a hung host MCU, two WAKE inputs for detecting switch activity during sleep, and a general purpose input for the limit switches and position sensors that dominate these applications. The very low power operating modes keep quiescent drain low on a vehicle that spends most of its life parked, while the 85 mA regulator is comfortably sized for a small MCU plus a position sensor. Because the HVSON package has a compact thermal pad, keep the layout within the manufacturer footprint guidance and provide adequate copper for regulator heat dissipation.
پێشنیارکراو
Low-Power LIN Sensor Node
Battery or body-powered LIN sensor nodes, such as seat-occupancy, sunroof or ambient temperature sensors, are designed around energy efficiency and simplicity. The TJA1128HTK/0Z fits that brief because one device covers the bus interface, the regulated supply for the sensing electronics, host supervision through the window watchdog, and external wake detection through two WAKE inputs and one GPI. The integrated LDO, available in 3.3 V and 5.0 V versions, removes a discrete regulator and its associated ceramic capacitor array from the layout. Keep the sensing front end within the 85 mA budget, and use the very low power sleep modes so the node wakes on demand rather than polling continuously.
پێشنیارکراو
LIN Cluster and HMI Back-End Interface
Cluster and human-machine-interface back-ends increasingly use LIN for switch and button sub-nets feeding a central display controller. The TJA1128HTK/0Z acts as the LIN endpoint that terminates such a branch: the 1/1 half-duplex transceiver communicates with the cluster MCU, the 85 mA LDO powers the local logic, the general purpose input latches a discrete input, and the HVMPO output drives a small indicator or relay coil where permitted. Its window watchdog gives the cluster a defined recovery behaviour if the master stops polling. Where a design needs richer diagnostics or faster reconfiguration than a basic LIN endpoint provides, the SPI-controlled TJA1145 offers an alternative path with a comparable footprint.
پێشنیارکراو
Battery-Backed Telematics Unit
Compact telematics and connectivity modules must handle a wide battery transient environment while keeping their own supply clean and their host supervised. The TJA1128HTK/0Z serves as the LIN interface and local regulator in such a unit: the AEC-Q100 qualification supports in-vehicle deployment, the integrated LDO supplies the host and its radio support circuitry up to 85 mA, and the window watchdog ensures the MCU recovers from a stalled firmware loop. The two wake inputs allow the unit to be woken by an ignition or accessory line, while the general purpose input can supervise an external enable. Review the recommended VBAT range and transient handling in the NXP datasheet, and keep radio supply demands on a separate rail if the node exceeds the 85 mA budget.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ TJA1128HTK/0Z — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | TJA1128FTK/0Z | TJA1145ATK/FD/0Z |
|---|---|---|---|
| Package | 14-HVSON (3 x 4.5 mm) | 14-HVSON (3 x 4.5 mm) - same | 14-HVSON (3 x 4.5 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Product Type | LIN Mini System Basis Chip (SBC) | LIN Mini System Basis Chip (SBC) | LIN System Basis Chip with SPI control |
| Host Interface | UART TXD/RXD to LIN transceiver | UART TXD/RXD to LIN transceiver | SPI |
| Automotive Qualification | AEC-Q100 qualified | AEC-Q100 qualified | AEC-Q100 qualified |
جیاکەرەوە سەرەکییەکان
- One device replaces a transceiver, a regulator and a supervisor (بەراورد بەTJA1145ATK/FD/0Z)
- Direct UART host interface keeps firmware simple (بەراورد بەTJA1145ATK/FD/0Z)
- Direct family substitution keeps the layout untouched (بەراورد بەTJA1128FTK/0Z)
- Very low power operation for parked-vehicle nodes (بەراورد بەTJA1128FTK/0Z)
تێبینییەکانی دیزاین
Estimated regulator budget: the 85 mA LDO rating must cover the LIN transceiver, the host microcontroller and every locally powered sensor. At a 5.0 V output that is up to 425 mW of dissipation from the regulator itself, so the input-to-output drop across the LDO, not just the load current, sets the thermal load. Add the transceiver's own bus load and the MCU's peak current before committing to this device as the only supply on the board, and move high-current loads such as motors and lamp strings to a dedicated driver stage.
Follow the recommended footprint and layout in the NXP TJA1128 datasheet rather than deriving an HVSON land pattern independently. Place the regulator input and output capacitors directly on their pins with the shortest possible traces, tie the exposed ground pad to a solid ground plane region, and keep the LIN bus trace away from the regulator and watchdog sections to limit injected noise on the single-wire bus. The pad also acts as the main heat path, so keep the pad free of thermal relief cutouts that would raise junction temperature.
Two failure modes dominate LIN node designs. First, the window watchdog timing must match the host firmware refresh cycle; too narrow a window causes spurious resets, too wide defeats the supervision. Second, the WAKE and GPI inputs sit on the battery-connected domain and must be protected against reverse battery and load-dump transients with the appropriate series and clamp network. Confirm the absolute maximum ratings in the datasheet before adding external circuitry that changes the pin loading.
LIN is a single-wire, dominant/ recessive bus with slow edges, so the transceiver itself is tolerant, but the host UART baud rate and the wake-up pulse timing still determine bus behaviour. Set the UART baud rate and the LIN frame timing from the datasheet timing section, keep the bus termination and pull-up arrangement per the reference circuit, and avoid routing the bus trace in parallel with the regulator supply trace over long distances, since shared impedance converts supply ripple into bus disturbance that shows up as communication errors.
زانیاری پابەندبوون
The part is AEC-Q100 qualified for automotive applications. RoHS, REACH, lead-free finish, halogen-free status and conflict-minerals declarations are not stated on this page and must be confirmed from the manufacturer product page or the manufacturer declaration before procurement release.