Logik-ICs
Produkte (2)
SN74AVC4T245QWRGYRQ1 - 4-Bit Dual-Supply Level Shifter AEC-Q100 | TI
The Texas Instruments SN74AVC4T245QWRGYRQ1 is an automotive-grade, 4-bit dual-supply bus transceiver with configurable voltage-level translation and 3-state outputs, packaged in a compact 16-pin VQFN (RGY, 4x3.5 mm) footprint. It enables bidirectional level shifting between buses operating at different supply voltages and is AEC-Q100 qualified for automotive use. A bus transceiver is a digital interface IC that combines transmit and receive paths in one device, allowing bidirectional data flow between two buses. The SN74AVC4T245-Q1 belongs to the voltage-level translator family, a subset of interface ICs within the broader integrated circuits category. Level translation is essential when connecting components with different I/O voltages, such as a 1.8 V microcontroller interfacing with a 3.3 V peripheral. Key features include dual-supply operation with VCCA and VCCB each accepting 1.2 V to 3.6 V, tri-state outputs for bus isolation, and Ioff partial-power-down protection that disables outputs and prevents damaging backflow current when either supply is removed. A typical propagation delay of 2.1 ns and data rates up to 380 Mbps make the device suitable for SPI, I2C, UART, and parallel GPIO interfaces. The CMOS architecture supports use as two independent 2-bit transceivers or one 4-bit transceiver. Direction control (1DIR, 2DIR) and output-enable (1OE, 2OE) pins are referenced to VCCA, simplifying control-logic design in mixed-voltage systems. The device operates asynchronously, requiring no clock signal, and is fully specified over the -40C to +125C automotive temperature range. Typical applications include automotive body control modules, ADAS ECUs, infotainment systems, and industrial automation. In ECUs, it bridges 1.8 V or 2.5 V MCUs to 3.3 V sensors, CAN transceiver interfaces, SPI flash, and general-purpose GPIO level shifting. Site-available companions include the SN65HVD230QDRQ1 CAN transceiver and SN74LVC1T45QDCKRQ1 single-bit translator. Design tip: decouple VCCA and VCCB with 0.1 uF capacitors placed close to the pins, and ensure DIR/OE signals (VCCA domain) are stable before data transmission to avoid bus contention.
TXB0104QRUTRQ1 - 4-Bit Auto-Direction Level Translator | TI
The Texas Instruments TXB0104QRUTRQ1 is an automotive-qualified 4-bit bidirectional voltage-level translator with automatic direction sensing, delivered in a compact 12-pin UQFN (RUT) package measuring 1.7 mm x 2.0 mm. It translates between a 1.2 V to 3.6 V A-port supply and a 1.65 V to 5.5 V B-port supply (VCCA <= VCCB), supporting data rates up to 100 Mbps. A voltage-level translator is a logic device that interfaces digital circuits operating at different supply voltages on the same PCB, such as a 1.8 V microcontroller talking to a 3.3 V or 5 V peripheral. translators sit within the broader logic IC hierarchy as members of the voltage-translation and signal-conditioning family used in mixed-voltage embedded systems. Key features include AEC-Q100 Grade 1 qualification (-40C to +125C ambient), +/-15kV IEC ESD protection on the I/O pins, and automatic direction sensing that eliminates direction-control pins or firmware overhead. The TXB family push-pull architecture uses internal one-shot edge accelerators, giving rise and fall symmetry suited to push-pull CMOS outputs. The 12-UQFN package enables very dense layouts in space-constrained automotive modules. Typical applications include automotive body electronics and lighting, infotainment and cluster SPI/I2C-adjacent push-pull signaling, sensor interface level shifting, and general-purpose MCU-to-peripheral level translation between 1.8 V, 2.5 V, 3.3 V, and 5 V domains. The wide 1.2 V low-side support makes it suitable for next-generation low-voltage processors. Design note: this device is intended for push-pull CMOS signals; for open-drain buses such as I2C, choose the TXS family instead. Do not add external pull-up or pull-down resistors on TXB I/O lines, as they can defeat the automatic direction sensing.