Mikrocontroller

Produkte (18165)

STM32F103VET6 - 512KB Flash 72MHz Cortex-M3 MCU | ST
STM32F103VET6

STM32F103VET6 - 512KB Flash 72MHz Cortex-M3 MCU | ST

The STMicroelectronics STM32F103VET6 is a high-density performance line 32-bit microcontroller based on the ARM Cortex-M3 RISC core running at up to 72 MHz, with 512 KB of Flash memory, 64 KB of SRAM, and a 100-pin LQFP (14x14 mm) surface-mount package. A microcontroller (MCU) is a compact integrated circuit that governs a specific operation in an embedded system by combining a processor core, memory, and programmable peripherals on one chip. The STM32F103VET6 sits in the embedded processing hierarchy as: MCU -> STM32F1 series -> STM32 family of ARM Cortex-M microcontrollers -> semiconductor device. It serves as the central control unit in industrial automation, motor control, and consumer electronics. Key features include the 72 MHz Cortex-M3 core delivering 1.25 DMIPS/MHz (Dhrystone 2.1), 512 KB Flash, 64 KB SRAM, and a rich peripheral set: three 12-bit ADCs, four general-purpose 16-bit timers plus two advanced PWM timers, and standard/advanced communication interfaces including USART, SPI, I2C, USB, CAN, and SDIO. Up to 80 GPIO lines, a DMA controller, and an RTC round out the integration. Technically, the high-density STM32F103xE devices integrate a Nested Vectored Interrupt Controller (NVIC) for deterministic interrupt latency, zero-wait-state Flash execution with prefetch buffer at 72 MHz, SWD and JTAG debug support, and multiple low-power modes (Sleep, Stop, Standby) for battery-sensitive designs. The 2.0V to 3.6V supply range supports 3.3V systems with 5V-tolerant IOs. Typical applications include industrial control systems, motor drives and inverters, medical instrumentation, POS/printing equipment, and IoT gateways where CAN, USB, and multiple ADC channels are required on a single chip. For design, provide 100 nF decoupling on each VDD/VSS pair plus a 4.7 uF bulk capacitor, keep the VCAP pins per datasheet guidance, and use the NRST pin with an external reset circuit for reliable in-field programming via SWD. This page synthesizes distributor pricing, drop-in alternatives (including GD32/CH32/APM32 cross-brand equivalents), and practical design notes not found in the STMicroelectronics datasheet.

USD $3,85 Auf Lager
STM32F103VET7 - 72MHz 512KB Cortex-M3 MCU | STMicroelectronics
STM32F103VET7

STM32F103VET7 - 72MHz 512KB Cortex-M3 MCU | STMicroelectronics

The STMicroelectronics STM32F103VET7 is a high-density 32-bit ARM Cortex-M3 microcontroller with a 72 MHz operating frequency, 512 KB of Flash memory, and a 100-LQFP package measuring 14 mm by 14 mm. It combines an RISC core with USB, CAN, 11 timers, three ADCs, and 13 communication interfaces for embedded control systems. A microcontroller is a programmable semiconductor system that executes firmware, reads sensor data, controls outputs, and coordinates connected peripherals. The STM32F103VET7 belongs to the STM32F1 performance-line family and provides substantially more integration than a basic eight- or sixteen-bit controller. Its Cortex-M3 architecture supports efficient interrupt-driven control, while Flash storage provides room for application code, configuration data, and boot logic. The verified feature set includes 512 KB Flash, 13 communication interfaces, three ADCs, 11 timers, USB, and CAN. These resources make the device suitable for industrial controllers, USB-connected instruments, CAN network nodes, and motor-control systems. Its 72 MHz maximum operating frequency provides computational headroom for protocol handling, signal sampling, and supervisory control tasks. The STM32F103xE high-density device family uses an Arm Cortex-M3 RISC core and combines communication, analog, and timing resources in one package. USB and CAN support can reduce the need for separate interface controllers, while the ADC and timer blocks can acquire and process external signals. Exact peripheral ratings, voltage limits, memory-map details, and electrical characteristics must be confirmed in the manufacturer datasheet. Typical designs include USB data-acquisition equipment, CAN-based industrial modules, motor-control boards, communication gateways, and compact embedded instruments. Firmware reuse is practical within appropriately qualified STM32 variants, but clock, peripheral, bootloader, supply, and qualification requirements still need verification before substitution. When laying out the PCB, preserve the manufacturer's 100-LQFP land pattern, power decoupling, clock routing, reset design, and exposed thermal requirements. The LQFP package provides accessible leads for inspection and rework, while the 14 mm by 14 mm body supports compact industrial controller designs. This page consolidates manufacturer specifications, distributor availability, sourcing data, and replacement constraints into an engineering reference. It also distinguishes verified facts from missing electrical details so designers can assess fit before beginning layout or firmware deployment.

Angebot Auf Lager
STM32F103VGT7 - 72MHz Cortex-M3 MCU 1MB Flash 100-LQFP | ST
STM32F103VGT7

STM32F103VGT7 - 72MHz Cortex-M3 MCU 1MB Flash 100-LQFP | ST

The STMicroelectronics STM32F103VGT7 is a 32-bit ARM Cortex-M3 microcontroller from ST's XL-density performance line of the STM32F1 family, operating at up to 72 MHz with 1 MB of embedded Flash and 96 KB of SRAM, housed in a 100-pin LQFP (14x14 mm) package. The device integrates high-speed embedded memories and an extensive set of enhanced I/O peripherals, including USB full-speed, CAN 2.0B, three SPIs, two I2S, two I2C, three USARTs, an SDIO interface and a 12-bit ADC with up to 1 MSPS sampling on multiple channels. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory and programmable I/O peripherals onto one die. Within the broader IC taxonomy, an MCU belongs to the microprocessor IC family, which sits above microcontrollers but below microprocessors in computational capability. The Cortex-M3 core inside this STM32 belongs to ARM's Cortex-M profile, designed for deterministic real-time embedded workloads; the Cortex-M3 line is one rung below Cortex-M4 in DSP capability and one rung above Cortex-M0+ in raw compute throughput. Key features of the STM32F103VGT7 include a 72 MHz maximum CPU clock with single-cycle multiply, two 12-bit ADCs (1 µs conversion), seven general-purpose 16-bit timers plus one PWM timer for motor control, three USARTs, two UARTs, two SPIs and one I2C, an FS-USB device, a CAN 2.0B interface, an SDIO interface, an FSMC for external memory, 80 GPIO lines and a -40 °C to +105 °C operating range. The XL-density die provides the largest Flash and SRAM footprint of the STM32F1 series, enabling sophisticated firmware with rich connectivity stacks. The architecture pairs a Harvard-bus Cortex-M3 with a multi-AHB bus matrix that lets CPU, DMA and peripherals operate concurrently with deterministic bus latency. The 72 MHz core drives a 1.25 DMIPS/MHz figure (1.25 DMIPS/MHz), yielding 90 DMIPS total performance. The chip supports JTAG and SWD debug, an embedded Cortex-M3 trace macrocell (ETM), and boundary-scan for production test. Typical uses include motor drives (BLDC, stepper), USB HID/COM bridges, industrial PLCs, CNC controllers, CNC and 3D-printer mainboards, data-acquisition modules, CAN-bus nodes, RFID readers and point-of-sale terminals. Designers favor the part for its mature firmware ecosystem (HAL, LL, StdPeriph), reference schematics and broad ST Nucleo board support. When laying out, place the VDD/VSS/VBAT/VDDA pins with 100 nF decoupling within 3 mm of each power pin, plus a 1 µF bulk on VDDA; keep the HSE crystal traces short and guarded to avoid EMI on USB. Make sure the BOOT0 strap on the part is hardware-defaulted for Flash boot when designing for field upgrades. This page consolidates distributor pricing (as of 2026-10-21), pin-to-pin same-brand and cross-brand drop-in alternatives (GD32F103 series) and practical design notes not found in the manufacturer datasheet.

USD $8,60 Auf Lager
STM32F103Z - 72MHz Cortex-M3 MCU, 144-LQFP | STMicroelectronics
STM32F103Z

STM32F103Z - 72MHz Cortex-M3 MCU, 144-LQFP | STMicroelectronics

The STMicroelectronics STM32F103Z is a high-density ARM Cortex-M3 32-bit microcontroller in the STM32F1 performance line, available in a 144-pin LQFP package. The Z-suffix family includes the STM32F103ZC (256 KB Flash), ZD (384 KB Flash), and ZE (512 KB Flash) variants, all running up to 72 MHz CPU clock and offering up to 1 MB of Flash in the broader F1 portfolio. This MCU integrates 64 KB SRAM, USB full-speed, CAN, multiple USART/SPI/I2C peripherals, a 12-bit ADC, and a 16-bit PWM timer block, making it a versatile choice for embedded applications. What is an ARM Cortex-M3 microcontroller? A Cortex-M3 MCU is a 32-bit processor core designed by ARM specifically for embedded deterministic real-time control. Within ST's product hierarchy, the Cortex-M3 sits between the Cortex-M0 (lowest cost/performance) and Cortex-M4 (DSP/FPU). The STM32F103Z belongs to ST's mainstream performance line, balancing cost, peripheral richness, and the 72 MHz speed grade against newer STM32F4/F7/H7 families that scale to 180-480 MHz. Key features include 72 MHz ARM Cortex-M3 core with single-cycle multiplication and hardware division, 512 KB Flash (ZE variant) with zero-wait-state execution, and 64 KB SRAM. The device supports 1.25 DMIPS/MHz performance, USB 2.0 full-speed with on-chip PHY, CAN 2.0B, three 12-bit ADCs with 1 µs conversion time, four 16-bit timers, and up to 112 general-purpose I/O pins. The 144-LQFP package provides extensive connectivity while remaining hand-solderable. Architecturally, the STM32F103Z uses a multi-AHB bus matrix that allows simultaneous CPU and DMA access to peripherals and memory, minimizing wait states. The integrated voltage regulator supports 2.0-3.6 V single-supply operation with internal 1.8 V core LDO. The 12-bit ADC group can be triggered by timers for synchronized motor-control sampling. Typical applications include industrial control and human-machine interfaces (HMIs), motor drives and inverters, USB peripherals and CAN-bus nodes, point-of-sale terminals, GPS data loggers, and barcode scanners. The wide peripheral set and large pin count also make it popular as a main controller for printers, 3D-printer boards, and mid-range IoT gateways. When designing with this MCU, prioritize decoupling: place 100 nF ceramic capacitors on every VDD/VDDA pin within 5 mm of the lead, and add a 4.7 µF bulk capacitor. For noise-critical ADC sampling, use a separate ferrite-isolated analog supply and enable the internal voltage-reference buffer. This page synthesizes pricing tiers, drop-in alternatives such as GD32F103, and PCB layout guidance beyond what is in the ST datasheet.

USD $7,10 Auf Lager
STM32F103Z8T6 - 72MHz Cortex-M3 MCU 64KB LQFP-144 | STMicroelectronics
STM32F103Z8T6

STM32F103Z8T6 - 72MHz Cortex-M3 MCU 64KB LQFP-144 | STMicroelectronics

The STMicroelectronics STM32F103Z8T6 is a 32-bit ARM Cortex-M3 microcontroller running at 72 MHz with 64 KB Flash and 20 KB SRAM, housed in a 144-pin LQFP (T6, LQFP-144) package. It belongs to the medium-density performance line of the STM32F103 series and integrates USB 2.0 full-speed, CAN 2.0B, multiple USARTs, SPI, I2C, and dual 12-bit ADCs. A microcontroller (MCU) is a single-chip computer combining a processor core, memory, and peripherals, sitting at the lowest level of the embedded-system hierarchy: MCU -> embedded processor -> system-on-chip. The STM32F1 family was one of the first mainstream ARM Cortex-M families and remains one of the most widely deployed MCU platforms in industrial, consumer, and communication equipment worldwide. Key features of the STM32F103Z8T6 include the 72 MHz Cortex-M3 core with fast interrupt handling, 64 KB (64K x 8) Flash program memory with ECC-style write protection, 20 KB SRAM, two 12-bit 1 us ADCs, seven 16-bit timers including advanced motor-control PWM timers, and a rich I/O count enabled by the 144-pin package with up to 112 GPIOs. Per the ST STM32F103x8/B datasheet, the device operates from a 2.0 V to 3.6 V supply across -40C to +85C (temperature grade 6). Technically, the medium-density STM32F103 uses an ARMv7-M architecture with a 3-stage pipeline and Harvard bus structure, plus an embedded Flash accelerator that keeps performance close to zero-wait-state execution at 72 MHz. DMA over the bus matrix offloads data movement for ADC, USART, SPI, and I2C, minimizing CPU overhead in real-time control loops. Typical applications include industrial control and PLC I/O modules, motor control (BLDC/FOC via the advanced timers and dual ADC), communication and gateway boards using CAN and multiple UARTs, consumer appliances, and low-cost development platforms such as the well-known Blue Pill family (which uses the 48-pin sibling STM32F103C8T6). When designing with this part, verify Flash wait-state settings at 72 MHz (2 wait states), respect the 3.6 V absolute maximum on VDD, and remember the famous revision-Y errata affecting some early USB implementations - consult errata sheet ES096 for details. This page synthesizes distributor pricing context, verified drop-in alternatives (including GigaDevice GD32F103), and practical design notes not found in the manufacturer datasheet alone.

USD $3,55 Auf Lager
STM32F103ZCT6 - 72MHz Cortex-M3 256KB MCU | STMicroelectronics
STM32F103ZCT6

STM32F103ZCT6 - 72MHz Cortex-M3 256KB MCU | STMicroelectronics

The STMicroelectronics STM32F103ZCT6 is a high-density performance line 32-bit microcontroller with an ARM Cortex-M3 core running at 72 MHz, 256 KB Flash and 48 KB SRAM, housed in a 144-pin LQFP (20x20 mm) package. A microcontroller (MCU) is a single-chip embedded computer that integrates a processor core, program memory, data memory, and programmable peripherals. Within the voltage regulator-like hierarchy of embedded silicon, the MCU sits at the system level: microcontroller -> ARM Cortex-M processor -> STM32 family -> STM32F1 high-density performance line. The STM32F103 series is one of the most widely adopted Cortex-M3 families in industrial and consumer electronics because it pairs deterministic real-time performance with a rich peripheral set and long-term availability. Key features of the STM32F103ZCT6 include the 72 MHz Cortex-M3 core with single-cycle multiply and hardware divide, 256 KB of embedded Flash, 48 KB SRAM, and up to 13 communication interfaces. Peripherals include three 12-bit ADCs, 11 timers, USB 2.0 full-speed device, CAN 2.0B, and a DMA controller. These resources allow a single chip to handle motor control loops, protocol conversion, and USB connectivity simultaneously. Technically, the device is fabricated on a 130 nm process and includes a Nested Vectored Interrupt Controller (NVIC) for low-latency interrupt handling. Both JTAG and Serial Wire Debug (SWD) interfaces are supported, and the embedded bootloader enables Flash programming over USART, USB, or CAN without a dedicated programmer. The core operates from a 2.0V to 3.6V supply across a -40C to +85C temperature range. Typical applications include industrial control systems, motor drives, medical devices, consumer electronics, and IoT gateways, where multiple communication interfaces and three ADCs allow sensor acquisition, actuation, and networking on one device. A key design consideration: decouple every VDD/VDDA pin with 100 nF capacitors placed as close as possible to the pins, configure BOOT0 correctly for the boot mode, and fit an external reset network on NRST for reliable startup. This page adds distributor-sourced availability data, drop-in alternatives including GigaDevice GD32F103 cross-references, and practical design notes not found in the STMicroelectronics datasheet alone.

Angebot Auf Lager
STM32F103ZCT7 - 72MHz 256KB Cortex-M3 MCU | STMicroelectronics
STM32F103ZCT7

STM32F103ZCT7 - 72MHz 256KB Cortex-M3 MCU | STMicroelectronics

The STMicroelectronics STM32F103ZCT7 is a 32-bit ARM Cortex-M3 microcontroller operating up to 72 MHz with 256 KB of Flash memory in a 144-pin LQFP package. It is designed for high-density embedded systems that need broad peripheral connectivity, deterministic control, and substantial on-chip program memory. What is an ARM Cortex-M3 microcontroller? An MCU combines a processor core, memory, and peripherals on one integrated circuit. The Cortex-M3 core provides a 32-bit instruction set and RISC-oriented embedded architecture, while the STM32F103 family integrates communication, timing, analog, and digital-control resources for applications spanning industrial equipment, communications, and mixed-signal control. The STM32F103ZCT7 combines 72 MHz operation, 256 KB Flash, and a high pin count in one device. Verified distributor material also identifies the part as a 144-pin MCU and highlights USB, CAN, timer, ADC, and communication-interface resources. These peripherals make it suitable for systems combining control logic with protocol handling and analog measurement. The STM32F103ZCT7 belongs to the STM32F103 high-density performance line. Its architecture supports connected embedded designs that need more GPIO and peripheral capacity than smaller STM32 packages. The 144-pin LQFP format provides extensive external connectivity, while the Cortex-M3 platform supports established embedded software tooling and real-time control workloads. Typical applications include industrial controllers, USB-connected peripherals, CAN-based equipment, data-acquisition systems, timer-driven control platforms, and embedded communications equipment. In these systems, the microcontroller can coordinate sensors, actuators, protocol transceivers, and human-interface or debug connections through its broad pin and peripheral set. A key design consideration is supply and decoupling planning. The verified data identifies 2.5 V and 3.3 V device variants, but detailed voltage ranges, pin-level electrical limits, clock configuration, memory map, and exact peripheral ratings were not supplied here and should be confirmed in the manufacturer datasheet before layout or firmware release. Firmware migration also requires validation of startup files, peripheral behavior, timing, and toolchain support. This page combines verified distributor specifications, practical application context, package constraints, and sourcing guidance for engineers evaluating the STM32F103ZCT7. It is designed to make technical comparisons faster while clearly separating confirmed data from parameters that require datasheet verification.

USD $7,65 Auf Lager
STM32F103ZEH6 - 72MHz Cortex-M3 512KB MCU | STMicroelectronics
STM32F103ZEH6

STM32F103ZEH6 - 72MHz Cortex-M3 512KB MCU | STMicroelectronics

The STMicroelectronics STM32F103ZEH6 is a high-performance 32-bit ARM Cortex-M3 microcontroller operating at 72 MHz, with 512 KB of Flash memory and a 144-pin LQFP package. It belongs to the STM32F1 performance-line family and integrates USB, CAN, 11 timers, three ADCs, and 13 communication interfaces. These headline resources make it suitable for connected industrial controls, embedded data acquisition, communications gateways, and multi-protocol control systems. A microcontroller is a programmable system-on-chip that executes firmware, reads sensors, controls actuators, and manages digital interfaces. The STM32F103ZEH6 combines an ARM Cortex-M3 RISC core with Flash program memory, SRAM, direct-memory-access support, and multiple peripherals. Within the hierarchy, it is an embedded microcontroller, a 32-bit MCU, and a member of the STM32 family of ARM-based semiconductor devices. Verified manufacturer information identifies a maximum CPU frequency of 72 MHz, 512 KB of Flash, USB, CAN, 11 timers, three ADCs, and 13 communication interfaces. Its broad peripheral mix allows several communications protocols and time-sensitive functions to coexist without external expansion devices. The high pin count also provides more externally accessible GPIO and peripheral connections than smaller STM32 packages. The ARM Cortex-M3 core provides the instruction set and processing foundation, while the STM32 peripherals handle timers, analog conversion, serial communications, USB, and CAN. Multiple timers support periodic generation, input capture, encoder-related functions, and motor-control workflows. Three ADC channels groups permit analog measurements, while communication interfaces reduce demand for discrete protocol controllers. Typical applications include industrial automation equipment, CAN-connected control panels, USB data loggers, communications hubs, motor controllers, and instrumentation gateways. The STM32F103ZEH6 is especially appropriate when firmware requires substantial Flash space and a broad set of embedded peripherals while retaining the established STM32F103 software ecosystem. Designers should verify the complete pin assignment, power supply requirements, clock configuration, and peripheral multiplexing against the manufacturer datasheet before layout. A 144-pin LQFP package also demands careful escape routing and thermal-aware placement. Published pricing and stock conditions should be checked with authorized distributors because availability can change independently of technical suitability. This page consolidates manufacturer specifications, distributor references, documented same-family alternatives, and practical procurement guidance. It also distinguishes verified data from unprovided parameters so engineers can assess fit without relying on assumptions.

Angebot Auf Lager
STM32F103ZET6 - 72MHz Cortex-M3 MCU 512KB Flash | STMicroelectronics
STM32F103ZET6

STM32F103ZET6 - 72MHz Cortex-M3 MCU 512KB Flash | STMicroelectronics

The STMicroelectronics STM32F103ZET6 is a high-density performance line 32-bit microcontroller built on the ARM Cortex-M3 core running at up to 72 MHz, with 512 KB of Flash memory, 64 KB of SRAM, and 112 GPIOs in a 144-pin LQFP (20 x 20 mm) package operating from a 2.0 V to 3.6 V supply. A microcontroller (MCU) is a compact integrated circuit that combines a processor core, memory, and programmable peripherals on a single chip to govern a specific operation in an embedded system. MCUs sit at the heart of the embedded electronics hierarchy - from the ARM Cortex-M processor core, through the STM32 family of 32-bit microcontrollers, up to complete embedded control systems used in industrial automation, consumer devices, and IoT products. Key features include three 12-bit ADCs with up to 21 channels, two 12-bit DACs, a 12-channel DMA controller, and an unusually rich communication set: up to 5 USARTs, 3 SPIs, 2 I2Cs, 1 CAN 2.0B, 1 USB 2.0 Full-Speed, and 1 SDIO interface. The Cortex-M3 core delivers 1.25 DMIPS/MHz (Dhrystone 2.1), giving roughly 90 DMIPS at 72 MHz, while the Nested Vectored Interrupt Controller (NVIC) provides low-latency deterministic interrupt handling. Architecturally, the device integrates advanced-control, general-purpose, and basic timers (including PWM timers for motor control), a real-time clock (RTC), and a CRC calculation unit. Both JTAG and Serial Wire Debug (SWD) interfaces are supported, and boot can be selected from Flash, system memory, or SRAM. The 512 KB Flash and 112 GPIOs of the LQFP144 make it the largest-pin, largest-memory STM32F103 variant, ideal for complex firmware with real-time control and multiple communication stacks. Typical applications include industrial control and PLC systems, motor drives, medical devices, communication boards, and IoT gateways. The wide 2.0 V to 3.6 V supply range and -40C to +85C operating temperature support both battery-powered and industrial designs. When designing with this device, decouple every VDD pin with 100 nF ceramic capacitors placed close to the pins plus one bulk capacitor, and filter VDDA with a ferrite bead to protect the 12-bit ADC noise floor. The BOOT0/BOOT1 pins must be strapped correctly at reset to select the desired boot source. This page adds value beyond the ST datasheet by synthesizing drop-in alternatives (GD32F103ZET6, APM32E103ZET6), pricing tiers, engineering design notes, and application guidance in one citable reference.

USD $5,39 Auf Lager
STM32F103ZET7 - 72MHz Cortex-M3 512KB MCU | STMicroelectronics
STM32F103ZET7

STM32F103ZET7 - 72MHz Cortex-M3 512KB MCU | STMicroelectronics

The STMicroelectronics STM32F103ZET7 is a 32-bit ARM Cortex-M3 microcontroller operating at up to 72 MHz, with 512 KB of embedded Flash memory and USB, CAN, 11 timers, 3 ADCs, and 13 communication interfaces. It is packaged in a 144-LQFP 20 mm x 20 mm package. The STM32F103ZET7 belongs to STMicroelectronics’ high-density performance-line STM32F1 MCU family. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, peripherals, and communication interfaces on one semiconductor device. The STM32F1 family combines an ARM Cortex-M3 RISC core with embedded control peripherals, making it suitable for industrial equipment, data acquisition, communications, motor control, and embedded automation. Its 32-bit architecture supports efficient control tasks and higher processing performance than many 8-bit or 16-bit alternatives. The STM32F103ZET7 provides 512 KB of Flash for firmware and 2.5 V/3.3 V operation as identified in the verified distributor and datasheet listings. Its feature set includes USB, CAN, 11 timers, 3 ADCs, and 13 communication interfaces. These resources allow one controller to coordinate analog measurement, timing, communication protocols, and control outputs while reducing the number of discrete components in a design. The device is identified as a 144-LQFP 20 mm x 20 mm surface-mount package. Its high pin count supports broad peripheral access and makes the STM32F103ZET7 useful for designs requiring numerous I/O functions, communications, and motor-control signals. The verified listing identifies the part as a 32-bit Cortex-M3 MCU with 72 MHz operation and 512 KB Flash memory. Typical applications include industrial control systems, IoT devices, embedded automation, motor control, metering equipment, USB-connected instrumentation, CAN-based nodes, and low-power embedded boards. Firmware selection should verify clock configuration, peripheral pin assignments, memory mapping, and the STM32F1 reference manual requirements before production release. This page combines verified manufacturer and distributor information with structured engineering guidance. Pricing, availability, lifecycle status, detailed electrical limits, and complete pin naming are not fully supplied in the retrieved data and must be confirmed against current manufacturer or distributor documentation before purchase or design approval.

USD $7,28 Auf Lager
STM32F103ZFT6 - 32-Bit 72MHz 768KB MCU | STMicroelectronics
STM32F103ZFT6

STM32F103ZFT6 - 32-Bit 72MHz 768KB MCU | STMicroelectronics

The STMicroelectronics STM32F103ZFT6 is a 32-bit ARM Cortex-M3 microcontroller with a 72 MHz maximum clock, 768 KB of Flash memory, and a 144-LQFP package measuring 20 mm by 20 mm. It belongs to the STM32F1 performance-line family and combines embedded control, communications, analog conversion, timer, and motor-control resources in one surface-mount device. An ARM Cortex-M3 microcontroller is a reduced-instruction-set embedded processor designed for real-time control systems. The Cortex-M3 core supplies deterministic instruction execution and interrupt handling, while the STM32F103 family integrates peripherals such as timers, communication interfaces, ADCs, USB, and CAN around that core. This hierarchy places the MCU above the processor core and into the broader embedded-control and semiconductor categories. The verified source data identifies the STM32F103ZFT6 as an XL-density member with 768 KB of Flash and a maximum frequency of 72 MHz. The same source states 1.25 DMIPS/MHz, supporting use in demanding embedded-control designs without requiring an external processor. Its large pin count also accommodates extensive I/O and peripheral connectivity compared with smaller STM32 packages. The manufacturer family description associates STM32F103 devices with USB, CAN, six timers, two ADCs, and six communication interfaces. These resources make the MCU suitable for gateways, motor controllers, industrial communication equipment, CAN or LIN-connected nodes, and embedded systems that require both control and communications. The verified data also lists vehicle gateway nodes and CAN/LIN networks as relevant use cases. A key engineering consideration is that the LQFP-144 footprint exposes substantially more interface pins than a compact MCU, enabling parallel I/O and multiple peripheral assignments while demanding careful PCB escape routing. Firmware and peripheral assignments should be validated against the manufacturer pinout and reference documentation before layout release. Alternate clock, memory, and analog behavior must also be checked when evaluating any substitute. This page combines verified distributor and manufacturer-linked source information, practical sourcing context, and structured MCU application guidance. It distinguishes the device’s confirmed 72 MHz and 768 KB attributes from parameters that remain unavailable, avoiding unsupported claims about electrical limits, temperature range, or compliance.

USD $17,81 Auf Lager
STM32F103ZGT6 - 72MHz Cortex-M3 1MB Flash MCU | ST | Industrial
STM32F103ZGT6

STM32F103ZGT6 - 72MHz Cortex-M3 1MB Flash MCU | ST | Industrial

The STMicroelectronics STM32F103ZGT6 is an XL-density performance line 32-bit microcontroller built on an ARM Cortex-M3 core running at 72 MHz with 1.25 DMIPS/MHz performance, 1 MB of Flash memory, and a 144-pin LQFP (20x20 mm) package. A microcontroller (MCU) is a single-chip embedded computer that integrates a processor core, memory, and peripherals on one die, sitting at the device level of the embedded systems hierarchy (MCU -> embedded processor -> semiconductor). The STM32F103 family, based on the ARM Cortex-M3 RISC architecture, is one of the most widely adopted 32-bit MCU platforms in industrial and consumer electronics, supported by an extensive tool ecosystem including STM32CubeIDE, Keil MDK, and IAR Embedded Workbench. Key features include 1 MB on-chip Flash with 96 KB SRAM, three 12-bit ADCs, ten general-purpose 16-bit timers plus two advanced PWM timers (17 timers in total), and 13 communication interfaces covering USB 2.0 full-speed, CAN 2.0B, multiple USARTs, SPI and I2C ports. According to the STMicroelectronics datasheet, the Cortex-M3 core delivers 1.25 DMIPS/MHz (Dhrystone 2.1), enabling deterministic real-time control. Technically, the XL-density devices add a FSMC (flexible static memory controller) for external memories and LCDs, a dual-SPI and SDIO interface, and an extensive DMA controller that offloads data movement from the CPU. The nested vectored interrupt controller (NVIC) provides low-latency interrupt handling essential for motor control and real-time I/O. Typical applications include industrial motor control, communication boards and gateways, medical instrumentation, and consumer appliances. The rich timer and PWM resources fit three-phase inverter drives, while USB and CAN interfaces suit fieldbus nodes and HID devices. Design consideration: power the MCU from a 2.0 V to 3.6 V supply and decouple each VDD pin with 100 nF ceramics; Flash wait states must be set to two at 72 MHz for 3.3 V operation. This page synthesizes distributor pricing, pin-to-pin alternatives (including GD32F103), and practical design notes not found in the manufacturer datasheet.

USD $5,40 Auf Lager
STM32F105RCT6 - 32-bit Cortex-M3 256KB Flash MCU | STMicroelectronics
STM32F105RCT6

STM32F105RCT6 - 32-bit Cortex-M3 256KB Flash MCU | STMicroelectronics

The STMicroelectronics STM32F105RCT6 is a 32-bit ARM Cortex-M3 microcontroller from the STM32F1 connectivity line, featuring 256KB of Flash memory, 64KB of SRAM, and a 72 MHz CPU, packaged in a 64-pin LQFP. It integrates connectivity peripherals including USB OTG full-speed, two CAN 2.0B interfaces, an Ethernet MAC (on F107), and multiple USART/SPI/I2C channels for industrial networking applications. The device operates from a 2.0V to 3.6V supply and supports extended temperature ranges from -40C to +85C or +105C depending on the order code suffix. What is a Cortex-M3 microcontroller? An ARM Cortex-M3 MCU is a 32-bit RISC processor core designed by ARM Holdings for embedded applications requiring deterministic real-time performance at low power. Positioned within the broader microcontroller taxonomy, it sits above 8-bit MCUs (8051, AVR) and below application processors in capability, while still delivering integer-only performance that suits motor control, sensing, and connectivity gateways. The STM32F1 series combines this core with ST's proprietary peripherals and a rich ecosystem of development tools. The STM32F105RCT6 architecture pairs the Cortex-M3 core with a multi-channel 12-bit ADC (1 MSPS), up to seven timers (including a PWM timer suited to motor control), and an integrated USB OTG controller with on-chip PHY. A unique dual-bank Flash layout (2x128KB read-while-write) supports in-field firmware upgrades without service interruption. The 7-channel DMA controller offloads data movement, freeing the CPU for protocol stacks and control loops. Connectivity is the STM32F105RCT6's defining strength relative to peers. The two CAN 2.0B controllers compliant with both standard 11-bit and extended 29-bit identifiers handle automotive and industrial bus rates up to 1 Mbit/s. Combined with USB OTG and multiple serial channels, the device suits gateway nodes bridging fieldbus, USB, and Ethernet networks on factory floors or in vehicle subsystems. The 72 MHz Cortex-M3 delivers 90 DMIPS (1.25 DMIPS/MHz), fast enough to run TCP/IP stacks or CANopen firmware without external coprocessors. Typical applications include industrial PLCs, building automation gateways, USB-to-CAN bridges, motor-drive controllers, point-of-sale terminals, and low-power IoT edge nodes with wired connectivity. Compared with older 8-bit or 16-bit MCUs, the F105RCT6 collapses multi-chip designs into one part, lowering BOM cost and PCB area. When designing, allocate decoupling capacitance near each VDD/VDDA pin, route the HSE crystal traces symmetrically with a ground guard ring, and use the boot pins (BOOT0/BOOT1) to enable system memory bootloader for USB DFU firmware update. The internal 8 MHz RC oscillator is accurate enough for many CAN applications, but a 32.768 kHz external crystal is recommended for RTC accuracy. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, including same-family variants such as STM32F107RCT6 and cross-brand substitutes from GigaDevice.

USD $4,85 Auf Lager
STM32F105VCT7 - 72MHz Cortex-M3 MCU 256KB Flash | STMicroelectronics
STM32F105VCT7

STM32F105VCT7 - 72MHz Cortex-M3 MCU 256KB Flash | STMicroelectronics

The STMicroelectronics STM32F105VCT7 is an ARM Cortex-M3 32-bit microcontroller operating at 72 MHz with 256 KB of Flash and 64 KB of SRAM, housed in a 100-pin LQFP (14x14 mm) package. Part of the STM32F105xx connectivity line family, it provides high-performance processing combined with a rich set of connectivity peripherals including USB OTG, CAN, Ethernet, USART, SPI, and I2C. An MCU (microcontroller unit) is a single-chip computer containing a processor core, program memory, data memory, and integrated peripherals. The Cortex-M3 core is a 32-bit RISC architecture designed by ARM for embedded applications, offering deterministic interrupt handling, hardware division, and Thumb-2 instruction set support for high code density. The STM32F105 sits in ST's connectivity line positioned above the STM32F103 performance line and below the STM32F107, distinguished by USB OTG full-speed and CAN interfaces but without on-chip Ethernet MAC (which is exclusive to the F107 series). Key features include 256 KB of embedded Flash with read-while-write support, 64 KB SRAM, 80 general-purpose I/O pins, two 12-bit ADCs with up to 16 channels, two 12-bit DACs, ten general-purpose timers, two I2C, three SPI, five USART, one USB OTG full-speed, two CAN 2.0B interfaces, and an SDIO interface. The internal 8 MHz RC oscillator with PLL provides the system clock, and the device supports 2.0 V to 3.6 V operating voltage. Typical applications include industrial control, USB peripherals, CAN gateways, point-of-sale terminals, motor control interfaces, PLCs, home appliances, and any USB-device-class peripheral needing CAN connectivity. The wide peripheral set and LQFP-100 footprint make it a versatile choice for human-machine interface (HMI) panels, low-cost Ethernet bridges (using external PHY+MAC), and USB-to-CAN bridges. When designing with this part, allocate decoupling capacitors near each VDD pin and route the HSE crystal traces symmetrically with short lengths to minimize EMI. The '7' suffix indicates the industrial temperature grade (-40C to +105C), suitable for most non-automotive applications. This page synthesizes distributor pricing, drop-in alternatives from the STM32F105/107 family, and practical PCB design notes not consolidated in the manufacturer datasheet alone.

USD $7,65 Auf Lager
STM32F107RCT6 - 256KB Flash Ethernet ARM MCU | STMicroelectronics
STM32F107RCT6

STM32F107RCT6 - 256KB Flash Ethernet ARM MCU | STMicroelectronics

The STMicroelectronics STM32F107RCT6 is a 32-bit microcontroller based on the ARM Cortex-M3 core running at up to 72 MHz, integrating 256 KB of Flash and 64 KB of SRAM, with Ethernet MAC, USB 2.0 OTG, two CAN 2.0B controllers, and a 64-pin LQFP (LQFP64, 10x10 mm, 0.5 mm pitch) package. What is a microcontroller (MCU)? A microcontroller is a compact integrated circuit that combines a processor, memory (Flash and SRAM), and programmable peripherals on a single chip. The STM32F107RCT6 belongs to STMicroelectronics' STM32F1 connectivity line family, which sits inside the broader STM32 32-bit ARM Cortex-M portfolio. The hierarchy is: microcontroller -> 32-bit MCU -> ARM Cortex-M MCU -> STM32 family -> STM32F1 series -> connectivity line. This positioning makes the STM32F107RCT6 well suited to embedded designs that demand both real-time control and wired connectivity. Key features include 1.25 DMIPS/MHz performance, 10/100 Mbps Ethernet MAC with MII/RMII, USB 2.0 OTG full-speed, two CAN 2.0B active controllers, three 12-bit ADCs (1 us conversion, up to 16 channels), two 12-bit DACs, and advanced-control timers with PWM resolutions as fine as 6.25 ns. Supply range is 2.0 V to 3.6 V with -40 C to +85 C operating temperature. Low-power modes include Sleep, Stop, and Standby, and the device adds a nested vectored interrupt controller (NVIC), memory protection unit (MPU), real-time clock (RTC), and CRC calculation unit. From a technical depth perspective, the STM32F107RCT6 is built on a 90 nm process node and uses a 12-channel DMA controller with independent streams. The 256 KB Flash is split into 4 x 64 KB sectors supporting read-while-write (RWW), enabling in-field firmware updates without halting the core. The Ethernet MAC requires an external PHY and a magnetics-isolated RJ-45, and the USB OTG controller supports both host and device roles. Compared with the lower-density STM32F105 sibling, the STM32F107 specifically adds the Ethernet MAC; compared with the STM32F103 mainstream line, the F107 adds CAN and Ethernet while preserving the same Cortex-M3 baseline. Typical applications include industrial PLC and motor-control boards, Ethernet-to-CAN or Ethernet-to-UART protocol gateways, smart metering, medical monitoring, point-of-sale terminals, and home/building automation hubs. The combination of Ethernet + USB OTG + dual CAN makes the STM32F107RCT6 a single-chip connectivity bridge for protocols such as Modbus TCP, CANopen, and USB CDC. When designing with this device, provide one 100 nF decoupling capacitor adjacent to each VDD pin plus a 4.7 uF bulk capacitor. Tie VDDA to a filtered analog rail and decouple VREF+ with 1 uF. For Ethernet, use a magnetics module with centre-tap termination; for USB OTG, add the 1.5 kohm pull-up on DP+ for full-speed device mode. Configure BOOT0 correctly for the desired boot source and place a 100 nF capacitor on NRST for reliable reset. This page synthesises distributor pricing, drop-in alternatives, and practical design notes that go beyond what appears in the manufacturer datasheet, providing engineers and buyers a single consolidated reference for the STM32F107RCT6.

USD $5,55 Auf Lager
STM32F107VCT6 - 256KB Flash 72MHz Cortex-M3 MCU | STMicroelectronics
STM32F107VCT6

STM32F107VCT6 - 256KB Flash 72MHz Cortex-M3 MCU | STMicroelectronics

The STMicroelectronics STM32F107VCT6 is a high-performance 32-bit microcontroller based on the ARM Cortex-M3 core operating at up to 72 MHz, integrating 256 KB of Flash memory and 64 KB of SRAM with Ethernet MAC, USB 2.0 OTG, and dual CAN 2.0B interfaces, housed in a 100-pin LQFP (14x14) package. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit that combines a processor core, program memory (Flash), data memory (SRAM), and programmable peripherals on a single silicon die, designed to govern a specific function within an embedded system. In the broader system hierarchy, a microcontroller sits above simple logic ICs but below application processors, offering a balance of deterministic real-time performance, low power consumption, and low cost for dedicated control tasks in industrial, consumer, and IoT products. Key features include 256 KB Flash (256K x 8), 64 KB SRAM, an integrated 10/100 Mbps Ethernet MAC with dedicated DMA, USB 2.0 OTG full-speed with on-chip PHY, two CAN 2.0B controllers, five USARTs, three SPIs, two I2Cs, two 12-bit ADCs with up to 16 channels, and a wide 2.0V to 3.6V supply range. The device operates over -40°C to +85°C industrial temperature range and is offered in the connectivity-line variant of the STM32F1 family. Technically, the STM32F107VCT6 is fabricated on ST's 90nm CMOS process, with single-cycle multiplication, hardware division, and a Nested Vectored Interrupt Controller (NVIC) supporting interrupt-driven design. The Ethernet MAC offloads packet handling through DMA, while the USB OTG full-speed interface integrates an on-chip transceiver, eliminating an external PHY for USB. Multiple low-power modes (Sleep, Stop, Standby) optimize energy consumption for battery-influenced designs. Typical applications include Ethernet gateways and industrial fieldbus bridges, USB device/host peripherals, CAN bus nodes in factory automation and automotive subsystems, and embedded human-machine interface controllers. The combination of Ethernet, USB OTG, CAN, and rich serial peripherals in one package reduces BOM cost and board footprint for multi-protocol communication hubs. When designing with this part, plan an external 25 MHz crystal for the Ethernet PHY reference, place 100 nF decoupling on each VDD/VDDA pin close to the package, and consider the boot-mode strap pin states during board bring-up. Verify Flash wait-state configuration when running the core above 48 MHz to ensure deterministic execution. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, supporting both new design-in and supply-chain risk mitigation.

USD $6,95 Auf Lager
STM32F205RCT6 - 120MHz Cortex-M3 MCU 256KB Flash | ST
STM32F205RCT6

STM32F205RCT6 - 120MHz Cortex-M3 MCU 256KB Flash | ST

The STMicroelectronics STM32F205RCT6 is a 32-bit ARM Cortex-M3 microcontroller operating at up to 120 MHz with 256 KB of Flash memory and 64 KB of SRAM, housed in a 64-pin LQFP (10 x 10 mm) package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals such as timers, communication interfaces, and analog-to-digital converters into one chip. Within the semiconductor hierarchy, the STM32F205RCT6 belongs to the STM32F2 series, which sits in STMicroelectronics' high-performance STM32 family of ARM-based MCUs, positioned above mainstream entry-level lines and below the highest-performance Cortex-M7 devices. Key features include the ARM Cortex-M3 core with the ART Accelerator (Adaptive Real-Time memory accelerator), which achieves 0-wait-state execution from Flash at 120 MHz and delivers 150 DMIPS (1.25 DMIPS/MHz per Dhrystone 2.1). The 256 KB Flash and 64 KB SRAM suit mid-size firmware images with protocol stacks. The device operates from a 1.8 V to 3.6 V supply (2.5 V/3.3 V typical rails) and integrates multiple USARTs, SPI, I2C, CAN, SDIO, USB OTG FS and HS interfaces, plus high-resolution timers and a 12-bit ADC for mixed-signal designs. Technically, the STM32F205RCT6 leverages a 90 nm process with an adaptive real-time memory accelerator that removes Flash wait-state penalties, so interrupt latency and deterministic execution are preserved even at full clock speed. A memory protection unit (MPU), nested vectored interrupt controller (NVIC), and comprehensive clock tree with PLL multiply the flexibility for real-time embedded workloads. Typical applications include industrial control and automation nodes, motor control and power inverters, medical and consumer devices, POS terminals, and communication gateways where the Connectivity Line peripherals (USB, CAN, SDIO) are used as bridges between interfaces. One key design consideration: the LQFP-64 pin count limits total GPIO and peripheral multiplexing, so verify pin allocation early; also budget decoupling capacitors per VDD pin and place the VCAP capacitor correctly for the internal 1.2 V regulator. This page synthesizes distributor pricing, same-family drop-in alternatives, pinout, and practical design notes not found in the manufacturer datasheet, with pricing as of 2026-09-06.

USD $4,15 Auf Lager
STM32F205RET6 - ARM Cortex-M3 MCU 120MHz 512KB | STMicroelectronics
STM32F205RET6

STM32F205RET6 - ARM Cortex-M3 MCU 120MHz 512KB | STMicroelectronics

The STMicroelectronics STM32F205RET6 is an ARM 32-bit Cortex-M3 microcontroller (MCU) in the STM32F2 connectivity line, integrating 512 KB of Flash and approximately 128+4 KB of SRAM in a 64-pin LQFP (10x10 mm) package. It runs at up to 120 MHz with 150 DMIPS / 1.25 DMIPS per MHz Dhrystone performance and pairs the core with ST's Adaptive Real-Time (ART) Accelerator that enables 0-wait-state execution from Flash. The device exposes up to 51 GPIOs, three 12-bit ADCs, two 12-bit DACs, 17 timers, USB OTG full- and high-speed, 10/100 Ethernet MAC, CAN 2.0B, plus multiple USART/UART/SPI/I2C controllers for high-mix industrial and consumer connectivity applications. An ARM Cortex-M3 microcontroller is a 32-bit RISC core (Cortex-M3 -> ARM Cortex-M family -> ARM 32-bit MCU -> embedded microcontroller -> semiconductor) optimized for deterministic real-time interrupt response and low power, complementing Cortex-M0/M0+ (cost) and Cortex-M4/M7 (DSP/FP) in the broader Cortex-M product tree. The STM32F2 family sits between Cortex-M3 and Cortex-M4 from a peripheral/integration standpoint; engineers choose the M3 variant (this part) when DSP extensions are unnecessary and the M4 when signal-processing throughput dominates. Key distinguishing features include 1 Mbyte maximum Flash addressability with 512 KB populated, 132 KB SRAM (including 4 KB backup SRAM), a parallel 16-bit 8080/6800 FSMC/NAND/PSRAM controller, an on-chip 8 MHz and 40 kHz RC oscillator with PLL, plus three 12-bit 2 MSPS ADCs capable of multiplexing 24 channels. Hardware cryptographic accelerators and a true random number generator (TRNG) are absent on the -F205 sub-line; the -F215 variant adds crypto/hash acceleration. Power domains include a 1.8 V internal LDO core regulator with a stop-mode current of roughly 25 µA typ. Typical applications are USB-to-Ethernet industrial gateways, CAN-connected motor and lighting controllers, point-of-sale terminals, biometric access modules, and human-machine interface (HMI) panels. The 10x10 mm LQFP-64 with 0.5 mm pitch balances I/O density with hand-repair-friendly leadouts for prototypes, while parts with the same outline at lower price (LQFP-48 from STM32F103) are available when fewer GPIO are required. When designing with this MCU, budget approximately 60 µA/MHz active current at 120 MHz and 25 µA stop current at 3.3 V VDD, and verify your VSMD/VREF+ decoupling network follows the datasheet reference layout. Pinout consistency across the STM32F205 sub-line (Z/R/V/T/C/U/BGA) means same-family parts with larger memory may be placed on this footprint with no PCB rework; however the LQFP-64 vs LQFP-48 vs LQFP-100 outlines are not interchangeable.

USD $7,95 Auf Lager
STM32F205RGT6 - 120MHz ARM Cortex-M3 MCU, 1MB Flash | STMicroelectronics
STM32F205RGT6

STM32F205RGT6 - 120MHz ARM Cortex-M3 MCU, 1MB Flash | STMicroelectronics

The STMicroelectronics STM32F205RGT6 is a high-performance ARM Cortex-M3 based microcontroller operating at up to 120 MHz, with 1 MB of flash memory and 128 KB of SRAM. It is housed in a 64-pin LQFP package (LQFP64) and is part of the STM32F2 series, which is designed for applications requiring high processing power, rich connectivity, and advanced analog features. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It contains a processor core, memory (flash for program storage and SRAM for data), and programmable input/output peripherals. In the system hierarchy, a microcontroller is a type of embedded processor, which falls under the broader category of integrated circuits. The STM32F205RGT6 is a mid-range MCU in the STM32 portfolio, positioned between the value-line STM32F1 series and the high-performance STM32F4/F7 series, offering a balance of performance, power efficiency, and peripheral integration. Key features of the STM32F205RGT6 include a 32-bit ARM Cortex-M3 core with a maximum clock speed of 120 MHz, 1 MB of flash memory, and 128 KB of SRAM. It supports a wide range of communication interfaces: 3x I2C, 4x USART, 2x UART, 3x SPI, 2x CAN, 1x USB 2.0 OTG FS/HS, 1x SDIO, and 1x Ethernet MAC. The device also integrates a 12-bit ADC with 16 channels, a 12-bit DAC with 2 channels, advanced timers, and a true random number generator (RNG). The operating voltage range is 1.8V to 3.6V, and the temperature range is -40°C to +85°C (industrial grade). The STM32F205RGT6 is built on a 90nm process technology, enabling high performance with low power consumption. It features a nested vectored interrupt controller (NVIC), a memory protection unit (MPU), and a flexible memory controller (FMC) for external memory expansion. The device supports a comprehensive set of low-power modes, including Sleep, Stop, and Standby, making it suitable for battery-powered applications. Typical applications include industrial control systems, motor drives, medical devices, consumer electronics, IoT gateways, and communication modules. Its rich connectivity and high processing power make it ideal for applications requiring real-time control and data processing. When designing with this MCU, ensure proper decoupling of the power supply pins with 100nF capacitors placed close to each VDD pin, and a 4.7uF bulk capacitor. The VDDA pin should be connected to a clean analog supply, and the VREF+ pin should be decoupled with a 1uF capacitor. For high-speed USB and Ethernet, follow the layout guidelines in the STM32F2xx reference manual (RM0033) to ensure signal integrity.

USD $8,10 Auf Lager
STM32F205VCT6TR - 120MHz Cortex-M3 MCU 256KB LQFP-100 | STMicroelectronics
STM32F205VCT6TR

STM32F205VCT6TR - 120MHz Cortex-M3 MCU 256KB LQFP-100 | STMicroelectronics

The STMicroelectronics STM32F205VCT6TR is a high-performance ARM Cortex-M3 32-bit microcontroller in the STM32F2 family, offered in a 100-pin LQFP package (tape-and-reel packaging variant) with 256 KB of Flash and 96 KB of SRAM. The Cortex-M3 core runs up to 120 MHz delivering 150 DMIPS, paired with a flexible ART Accelerator that provides 0-wait-state execution from Flash at the maximum CPU speed, equivalent to the throughput of a MIPS-class core running at 225 MHz on a 0-wait-state memory. An ARM Cortex-M3 microcontroller is a 32-bit RISC processor core built around the Thumb-2 instruction set and tightly integrated with NVIC (Nested Vectored Interrupt Controller), SysTick, and optionally MPU and ETM blocks. In the broader taxonomy, the Cortex-M3 sits under Cortex-M -> ARM -> 32-bit MCU -> microcontroller, and the STM32F2 specifically targets high-performance connectivity applications. The Cortex-M3 brings deterministic interrupt latency, hardware divide, single-cycle multiply, and atomic bit-band regions, all of which translate into predictable code execution and tight real-time behavior. Key features include 256 KB of Flash program memory, 96 KB of SRAM, three 12-bit ADCs with up to 24 channels, two 12-bit DACs, up to 17 timers (including motor-control PWM and general-purpose 16/32-bit timers), three I2C, four USART, two UART, three SPI, plus USB OTG Full-Speed and High-Speed with on-chip PHY, CAN 2.0B, SDIO, and 10/100 Ethernet MAC with dedicated DMA. The part operates from a 1.8 V to 3.6 V supply and provides multiple low-power modes (Sleep, Stop, Standby) with battery-domain RTC. Architecturally, the STM32F205 integrates the ART Accelerator, a 7-channel general-purpose DMA, a CRC engine, and a 96-bit unique device ID. The combination of hardware encryption support (AES, RNG, USB OTG, and external FSMC/SDIO access) makes it well suited for industrial gateways, smart-meter and building-automation controllers that require Ethernet and USB at the same time. Typical applications for the STM32F205VCT6TR include industrial motor drives and variable-frequency drives (VFD), barcode scanners and printers, home appliances with TFT/LCD HMIs, USB-connected medical instrumentation, alarm panels with Ethernet backhaul, and protocol converters bridging CAN, USB and Ethernet. The LQFP-100 footprint also makes it a strong fit for hand-soldered prototypes and medium-volume industrial designs. When designing with this part, fit decoupling per VDD/VBAT/VDDA pin, place a 32.768 kHz crystal on PC14/PC15 if RTC accuracy is needed, and route the HSE oscillator traces short. Always verify USB OTG HS PHY biasing (external resistor on DP pull) when the high-speed USB port is used. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not typically compiled inside the manufacturer datasheet PDF.

USD $7,95 Auf Lager
STM32F205VET6 - 120MHz ARM Cortex-M3 MCU, 512KB Flash | STMicroelectronics
STM32F205VET6

STM32F205VET6 - 120MHz ARM Cortex-M3 MCU, 512KB Flash | STMicroelectronics

The STMicroelectronics STM32F205VET6 is a high-performance ARM Cortex-M3 32-bit microcontroller operating at up to 120 MHz with 150 DMIPS performance, integrating 512KB of Flash memory and 132KB of SRAM in a 100-pin LQFP (14x14 mm) package. The device provides 82 user I/O pins and is qualified over the industrial -40C to +85C temperature range, making it suitable for demanding embedded designs. According to the STMicroelectronics STM32F205xx datasheet, this part is part of the STM32F2 family and supports supply voltages of 1.8V to 3.6V. A microcontroller (MCU) is a compact integrated circuit that combines a processor core, volatile and non-volatile memory, and programmable peripherals to govern a specific operation within an embedded system. MCUs sit in the hierarchy of embedded processors between simple 8-bit controllers and high-end application processors, and are optimized for deterministic real-time control and signal processing. The STM32F205VET6 specifically belongs to the ARM Cortex-M3 lineage (32-bit RISC core), positioning it above 8/16-bit microcontrollers in compute density while remaining below Cortex-A application processors in both cost and power. Key features include 120 MHz maximum CPU frequency, 512KB on-chip Flash (512K x 8 organization), 132KB SRAM, 17 general-purpose and advanced-control timers, 3x 12-bit ADCs, USB OTG High-Speed and Full-Speed, on-chip 10/100 Ethernet MAC, 2x CAN, 3x SPI, 3x I2C, 5x USART/UART plus UART, and a digital camera interface. The adaptive real-time (ART) memory accelerator reduces Flash wait states to deliver close-to-zero penalty execution from on-chip code, and the part supports cryptographic features such as the unique 96-bit device ID and RNG in this density. Technically, the STM32F205VET6 is fabricated on a low-power CMOS process and offers multiple low-power modes (Sleep, Stop, Standby) with fast wakeup times for battery-driven applications. The 100-pin LQFP package exposes 82 GPIOs tolerating 5V on most pins, includes an integrated voltage regulator for single-supply operation, and supports JTAG and SWD interfaces for in-circuit debug. Independent and window watchdog timers, a SysTick timer, and a real-time clock (RTC) with calendar and backup registers round out the on-chip resources. Typical applications include industrial automation and motor control, building and home automation gateways, consumer HMI with TFT or camera input, USB peripherals, Ethernet-connected IoT nodes, medical instrumentation, and point-of-sale terminals. Its combination of high CPU throughput, on-chip Ethernet and USB OTG HS makes it especially attractive when designers need wired connectivity without an external PHY companion MCU. When designing with this MCU, place decoupling capacitors (typically 100 nF + 4.7 uF) on each VDDA/VSS pair as close to the pins as the PCB layout allows, and route VBAT7 (VBAT) directly to a coin cell or supercap if RTC backup retention is required. Carefully observe BOOT0 pin configuration to select the correct boot source (main Flash, system memory bootloader, or embedded SRAM) and verify HSE/HSI clock tree values against the RM0033 reference manual before locking the firmware. This page synthesizes distributor pricing snapshots, drop-in alternatives, and design guidance that are not collected in any single place in the manufacturer datasheet, providing a faster procurement and design start than reading the full RM0033 reference manual from scratch.

USD $7,25 Auf Lager
STM32F205VET7 - ARM Cortex-M3 MCU, 512KB Flash, 120MHz | STMicroelectronics
STM32F205VET7

STM32F205VET7 - ARM Cortex-M3 MCU, 512KB Flash, 120MHz | STMicroelectronics

The STMicroelectronics STM32F205VET7 is a high-performance ARM Cortex-M3 32-bit microcontroller with 512KB of Flash memory, 120MHz CPU clock, and 100KB of SRAM, housed in a 100-pin LQFP (14x14) package. It integrates the ART Accelerator allowing 0-wait-state execution from Flash memory, achieving 150 DMIPS / 1.25 DMIPS/MHz (Dhrystone 2.1). The device operates from a 1.8V to 3.6V supply and includes an MPU for memory protection. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable I/O peripherals. The STM32 family sits within the ARM Cortex-M ecosystem — specifically Cortex-M3, which is a Harvard-architecture core optimized for deterministic real-time performance with low interrupt latency. Within STMicroelectronics' portfolio, the STM32F2 series targets high-performance embedded applications requiring rich connectivity (USB OTG, CAN, Ethernet MAC) combined with substantial on-chip memory, sitting between the mainstream F1 and the more advanced F4 lines. Key features include up to 1 Mbyte addressable Flash (512KB on this variant), 100KB SRAM with CCM (Core-Coupled Memory), three 12-bit ADCs (1 MSPS / 24 channels), two 12-bit DACs, and 17 timers. Communication peripherals include USB OTG full-speed/high-speed, two CAN 2.0B interfaces, an Ethernet MAC (with MII/RMII), three I2C, three SPI, four USART and two UART interfaces. The 100-pin LQFP package provides 82 user I/O pins with 5V-tolerant I/Os. The ART Accelerator paired with the 120MHz Cortex-M3 delivers efficient deterministic execution, allowing code to run from Flash at full speed without wait states — critical for DSP-style routines, motor-control loops, and protocol stacks. The integrated Ethernet MAC and dual CAN buses enable industrial networking and fieldbus applications, while the high-speed USB OTG supports device, host, and OTG modes for embedded peripherals. Typical applications include industrial control and PLC modules, motor drives and inverter control, USB peripherals and HID devices, CAN-based automotive body and chassis ECUs, Ethernet-connected IoT gateways, and human-machine interface (HMI) panels. The combination of memory density and peripheral mix suits it to multi-protocol industrial nodes. When designing with this device, ensure the regulator providing VDD/VDDA supplies clean 3.3V with adequate decoupling (typically 100nF per VDD pin plus 4.7uF bulk). The boot configuration pins (BOOT0/BOOT1) must be set correctly for the chosen boot source — main Flash, system memory (bootloader), or embedded SRAM. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Engineers can use the FAQ and design_notes sections below to accelerate schematic review and BOM validation.

USD $8,95 Auf Lager
STM32F205VGT6 - 120MHz ARM Cortex-M3 MCU 1MB Flash | STMicroelectronics
STM32F205VGT6

STM32F205VGT6 - 120MHz ARM Cortex-M3 MCU 1MB Flash | STMicroelectronics

The STMicroelectronics STM32F205VGT6 is a high-performance ARM Cortex-M3 32-bit RISC microcontroller operating at up to 120 MHz, delivering 150 DMIPs, with 1 MB of embedded Flash and 132 KB of SRAM in a 100-pin LQFP (14x14 mm) package. It belongs to the STM32F2 series, which combines connectivity peripherals with DSP and floating-point instructions, targeting industrial, consumer, and human-machine-interface applications. An ARM Cortex-M3 microcontroller (MCU) is a 32-bit RISC processor core designed by Arm for embedded systems, featuring deterministic interrupt latency, Thumb-2 instruction set, and optional hardware multiply-accumulate. Within the broader taxonomy, the Cortex-M3 sits under Arm Cortex-M → 32-bit MCU → embedded microcontroller → semiconductor IC. The STM32F2 family specifically targets applications that require high computational throughput plus rich connectivity (USB OTG, Ethernet, CAN, SDIO) without the higher cost of Cortex-M4 parts. Key features include 82 GPIO pins, three 12-bit ADCs (up to 2.4 MSPS), two 12-bit DACs, 17 timers, USB OTG Full-Speed and High-Speed, 10/100 Ethernet MAC, two CAN 2.0B controllers, an SDIO interface, and a camera interface. The integrated 4 KB backup SRAM retains data in standby mode while consuming only a few microamperes, and the part supports four low-power modes (Sleep, Stop, Standby, and VBAT) for battery-powered designs. The architecture uses a multi-AHB bus matrix with separate buses for SRAM, Flash, and peripherals, allowing parallel DMA transfers and Cortex-M3 core execution without contention. The 120 MHz clock is sourced from an internal 16 MHz RC oscillator (with PLL) or an external 4-26 MHz crystal, enabling flexible system clock trees. Cryptographic and FSMC functions are NOT included on the F205 sub-line (those land on the F207 sub-line), which keeps this part cost-optimized for non-crypto applications. Typical applications include industrial control (PLCs, motor drives, factory automation), medical equipment (patient monitors, diagnostic peripherals), consumer electronics (home appliances, audio devices with USB), networking (Ethernet-enabled IoT gateways, smart sensors), and human-machine interfaces (touchscreen controllers, graphical displays). The 1 MB Flash and 132 KB SRAM also suit firmware-over-the-air (FOTA) updates with rollback image storage. When designing with the STM32F205VGT6, ensure your PCB layout places the 100-pin LQFP's exposed pad (if present on the variant) onto a ground copper pour for thermal dissipation, and follow ST's application note AN2867 for oscillator PCB layout. Decouple VDD/VDDA/VBAT with 100 nF ceramic capacitors placed within 2 mm of each supply pin, and add a 4.7 uF bulk capacitor per supply rail. VDD operating range is 1.8-3.6 V (the V suffix), so verify your LDO selection covers this range with adequate transient response. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate second-source options and PCB migration paths for the STM32F205VGT6.

USD $8,10 Auf Lager
STM32F205ZET6 - 32-bit ARM Cortex-M3 MCU, 512KB Flash | STMicroelectronics
STM32F205ZET6

STM32F205ZET6 - 32-bit ARM Cortex-M3 MCU, 512KB Flash | STMicroelectronics

The STMicroelectronics STM32F205ZET6 is a high-performance 32-bit microcontroller based on the ARM Cortex-M3 core, operating at up to 120 MHz. It features 512 KB of Flash memory and 128 KB of SRAM, making it suitable for a wide range of embedded applications. The device is housed in a 144-pin LQFP package (LQFP144) with a 20x20 mm body and 0.5 mm pitch, providing ample GPIOs and connectivity options. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It integrates a processor core, memory (Flash and SRAM), and programmable input/output peripherals on a single chip. Microcontrollers are the backbone of embedded systems, enabling control, monitoring, and communication in applications ranging from consumer electronics to industrial automation. The STM32F205ZET6 belongs to the STM32F2 series, which is part of the broader STM32 family of 32-bit Flash microcontrollers based on the ARM Cortex-M processor. This family hierarchy positions the STM32F205ZET6 as a high-performance MCU with advanced connectivity and rich analog peripherals. Key features of the STM32F205ZET6 include a 32-bit ARM Cortex-M3 CPU with adaptive real-time accelerator (ART) allowing 0-wait state execution from Flash, a memory protection unit (MPU), and a comprehensive set of peripherals. It offers up to 114 I/O ports, 3x 12-bit ADCs, 2x DACs, 12-bit timers, and advanced communication interfaces including USB 2.0 OTG HS/FS, Ethernet MAC, CAN, SPI, I2C, USART, and SDIO. The device operates from a 1.8V to 3.6V power supply and supports a temperature range of -40°C to +85°C (industrial grade). Technically, the STM32F205ZET6 is built on a 90nm process technology, enabling high clock speeds with low power consumption. It includes a nested vectored interrupt controller (NVIC) for efficient interrupt handling, a DMA controller with 16 channels, and a true random number generator (RNG). The device also features a real-time clock (RTC) with calendar and alarm functions, and a flexible static memory controller (FSMC) for external memory expansion. Typical applications include industrial control systems, motor drives, medical devices, consumer electronics, and IoT gateways. Its rich connectivity and high processing power make it ideal for applications requiring real-time control and communication, such as PLCs, robotics, and smart home hubs. When designing with the STM32F205ZET6, ensure proper decoupling of the power supply pins with 100nF capacitors placed close to each VDD pin, and a 4.7uF bulk capacitor. The VDDA pin should be connected to a clean analog supply to minimize noise in ADC conversions. Also, configure the boot pins correctly to select the desired boot mode (Flash, SRAM, or system memory) for programming and debugging.

USD $8,10 Auf Lager