Leistungsmanagement
Unterkategorien
Produkte (2770)
ADIN1300BCPZ-R7 - Gigabit Ethernet PHY, 10/100/1000 Mbps, 40-LFCSP | Analog Devices
The Analog Devices ADIN1300BCPZ-R7 is a low-power, single-port Gigabit Ethernet transceiver (PHY) supporting 10 Mbps, 100 Mbps, and 1 Gbps data rates in a 40-pin LFCSP-WQ (6x6 mm) package with wettable flanks. It delivers best-in-class latency under 290 ns (100 Mbps) and sub-400 ns (1000 Mbps) while consuming only 257 mW typical at 1 Gbps full duplex, designed specifically for industrial Ethernet, EtherCAT, PROFINET, and TSN applications. The device integrates an Energy Efficient Ethernet (EEE) physical layer, 802.3az support, automatic MDI/MDIX crossover, and on-chip termination resistors. An Ethernet PHY (physical layer transceiver) is the analog front-end in a layered network stack that converts between digital MAC-domain data and the differential analog signals on the twisted-pair cable. It sits below the MAC layer in the OSI model, handling line coding (PAM/PMA), link training, baseline wander correction, and signal equalization. Industrial PHYs such as the ADIN1300 are hardened against ESD, EMC, and temperature extremes, and they support deterministic latency demanded by real-time motion-control protocols. Key features of the ADIN1300 include 4 kV HBM ESD rating on MDI pins, integrated 1.25V LDO regulators, programmable RGMII/GMII/MII MAC interface, IEEE 1588 time-stamping support, and a configurable MDIO/MDC management interface. The 40-LFCSP-WQ package provides excellent thermal performance for fanless industrial designs and supports reflow soldering with its wettable flank terminations that enable automated optical inspection (AOI). The ADIN1300 uses a DSP-based echo canceller and baseline-wander correction loop, enabling robust 1000BASE-T operation over 100 m of CAT5e/6 cable even in electrically noisy industrial cabinets. The integrated PHY reduces BOM count versus MAC-plus-discrete-PHY designs and includes diagnostic features such as cable diagnostics, signal quality indicator (SQI), and loopback modes for factory test. Typical applications include industrial Ethernet switches, PLC communication modules, EtherCAT slave nodes, motion controllers, building automation gateways, and embedded IoT gateways requiring deterministic real-time networking. The wide -40C to +85C industrial temperature range supports outdoor and factory-floor deployment without additional thermal management. When designing with this device, ensure the MAC interface voltage matches the RGMII/GMII/MII logic level (1.8V, 2.5V, or 3.3V selectable via strapping resistors). Place the 25 MHz reference clock or crystal within 1 cm of the XI/XO pins to minimize jitter, and provide an isolated RJ45 magnetics module rated for 1 Gbps operation. Decouple each AVDD/DVDD pin with 100 nF plus 10 uF bulk capacitors to control power-supply noise coupling into the analog front-end. This page synthesizes distributor pricing, drop-in alternatives, and application guidance not consolidated on the manufacturer datasheet - useful for engineers sourcing the ADIN1300BCPZ-R7 for new designs or second-source qualification.
ADM1278-1ACPZ-RL - Hot Swap Controller + PMBus Monitor | ADI
The Analog Devices ADM1278-1ACPZ-RL is an integrated hot-swap controller and digital power-and-energy monitor with a PMBus-compatible interface, housed in a 32-pin LFCSP (5x5 mm) package. It targets 1.4 V to 20 V positive-rail hot-swap applications and integrates a 12-bit ADC for telemetry of VIN, VOUT, IOUT and on-die temperature. The device supports programmable current-limit thresholds from 5 mV to 25 mV across a sense resistor, with a 290 ns response time to short-circuit events. A hot-swap controller is a specialized power-management IC that sits between a live backplane and a removable circuit card, controlling the inrush current that flows when bulk load capacitance charges up. Without it, the charged capacitor looks like a momentary short, which can trip upstream supplies, cause connector arcing, or damage FETs. The ADM1278 combines that inrush-control role with on-board telemetry: a PMBus interface reports voltage, current, power and energy in real time so the system host can implement digital energy budgets, logging, and predictive analytics. Within the broader taxonomy, hot-swap controllers sit under hot-swap and ORing controllers -> power management ICs -> power management. Key features include constant-power folded-back current limiting for tighter FET SOA protection, programmable linear inrush current profile on power-up, FET-health monitoring with auto-shutdown on fault, and remote temperature sensing with programmable warning and shutdown thresholds. The integrated PMBus block supports readback of voltage, current, power and energy in a standard format readable by any supervisory MCU or BMC. The -1 suffix in the part number denotes the LFCSP package variant with specific pin assignments as described in the datasheet. Architecturally, the chip uses an external N-channel MOSFET as the high-side pass element, a high-side current-sense amplifier, a precision bandgap-referenced 12-bit ADC, and an I2C/SMBus-compatible PMBus interface block. The ADI datasheet (Rev. C) describes a constant-power foldback mode that derates the gate drive as VDS across the FET rises, holding the FET inside its thermal envelope during sustained fault events. Typical applications include server and datacenter hot-swap boards, network switches and routers with removable line cards, RAID/HBA cards, blade-server mezzanine cards, PCI Express add-in cards, and -48 V distribution systems with intermediate bus converters. Industrial applications requiring PMBus telemetry such as programmable DC supplies and remote radio units (RRUs) also benefit from the integrated monitoring. When designing with the ADM1278, choose the external MOSFET first - its SOA and RDSon drive efficiency, fault tolerance and thermal performance. The sense resistor value (RSENSE) directly sets the current-limit threshold, and a 1% tolerance part is strongly recommended for accurate telemetry. The PMBus address is resistor-programmable, allowing multiple hot-swap ICs to coexist on a single bus.
ADM705ARZ-REEL - 4.65V Microprocessor Supervisor | Analog Devices
The Analog Devices ADM705ARZ-REEL is a low-cost microprocessor supervisory circuit that monitors a 4.65V threshold and provides an active-low push-pull reset output, housed in an 8-pin SOIC (R-8) package and supplied on a 2500-piece tape-and-reel. It is designed for 5V power supply/battery monitoring in microprocessor-based systems and generates a reset during power-up, power-down, and brownout conditions. A microprocessor supervisor (also called a voltage supervisor or reset IC) is a power-management IC that watches the system supply rail and asserts a reset signal to the host processor whenever the rail falls below a preset threshold. This prevents code execution at unsafe voltages, which can lead to corrupted flash, latched peripherals, or indeterminate logic. Supervisors sit in the power-management IC hierarchy between simple voltage detectors and full PMICs, and are essential building blocks in any MCU/MPU-based design. Key features include a guaranteed valid RESET output with VCC as low as 1V, 190 µA typical quiescent current, a 200 ms reset pulse width, a 160 ms minimum reset timeout, and a debounced TTL/CMOS manual reset (MR) input. The reset output uses a push-pull totem-pole stage, eliminating the external pull-up resistor that open-drain alternatives require. The part is specified over the -40 °C to +85 °C industrial temperature range and ships in Pb-free/RoHS-compliant packaging. The ADM705 family shares its pinout across the ADM705/ADM706/ADM707/ADM708 series, allowing the designer to substitute parts to trade watchdog timing, or push-pull/open-drain output polarity, without re-laying-out the PCB. This drop-in compatibility, combined with low quiescent current and 1V-reset-valid operation, makes the ADM705 a long-standing industry staple for 5V supervisory designs. Typical applications include reset and supply monitoring for 8051, PIC, AVR, MSP430, and ARM Cortex-M microcontrollers, embedded industrial controllers, point-of-sale terminals, automotive body electronics, and battery-backed systems. The wide operating range and high noise immunity also suit it to noisy motor-control and SMPS post-regulation environments. When designing with this device, place the 1 µF bypass capacitor as close as possible to VCC and route MR with a short, debounced trace. Note that the ADM705 does not include a watchdog timer - choose the ADM706 if watchdog functionality is required.
ADP1031ACPZ-1 - Isolated PMU with 3 Regulators | Analog Devices
The ADP1031ACPZ-1 is a high performance, isolated micropower management unit (PMU) from Analog Devices that integrates an isolated flyback dc-to-dc regulator, an inverting dc-to-dc regulator, and a buck dc-to-dc regulator, providing three isolated power rails. It also includes four high speed serial peripheral interface (SPI) isolation channels, making it ideal for isolated data acquisition and industrial applications. The device is housed in a 41-lead LFCSP (9x7 mm) package and operates over a wide input voltage range. An isolated PMU is a power management IC that combines multiple power conversion stages with galvanic isolation, enabling safe and noise-free power transfer across an isolation barrier. It integrates the isolation components (such as transformers) and control circuitry into a single package, simplifying design and reducing board space. The ADP1031 belongs to the family of isolated power management units, which are essential in industrial automation, medical equipment, and communication systems where safety and noise immunity are critical. Key features of the ADP1031ACPZ-1 include a wide input voltage range, high efficiency, and integrated isolation. The flyback regulator provides a regulated output, while the inverting and buck regulators offer additional rails with different polarities and voltage levels. The device also features overvoltage protection (OVP) on the inverting regulator, which monitors the FB3 pin and stops switching if the voltage falls below VFB3 by 10%, ensuring safe operation. The integrated SPI isolation channels eliminate the need for external digital isolators, reducing component count and system cost. Technically, the ADP1031 uses a proprietary architecture that combines a primary-side controller with secondary-side regulation, achieving high efficiency and accurate output regulation. The device supports a wide range of output voltages and currents, making it versatile for various applications. The package is designed for excellent thermal performance, with an exposed pad for heat dissipation. Typical applications include isolated data acquisition systems, industrial process control, programmable logic controllers (PLCs), and isolated sensor interfaces. The device is particularly suited for applications requiring multiple isolated power rails and high-speed data isolation, such as motor drives and smart grid equipment. When designing with the ADP1031ACPZ-1, it is important to carefully select the external transformer and components to meet the required isolation and efficiency specifications. Proper PCB layout is essential to minimize noise and ensure reliable operation. The device also requires careful thermal management due to its power dissipation.
ADP1031ACPZ-2 - Isolated PMU with 7 Digital Isolators | Analog Devices
The ADP1031ACPZ-2 is a high performance, isolated micropower management unit (PMU) from Analog Devices that integrates an isolated flyback dc-to-dc regulator, an inverting dc-to-dc regulator, and a buck dc-to-dc regulator to provide three isolated power rails. Additionally, it contains four high-speed serial peripheral interface (SPI) digital isolator channels and three general-purpose digital isolator channels, totaling seven digital isolators. This device is designed for industrial applications requiring galvanic isolation and multiple isolated power domains. An isolated PMU is a power management IC that combines isolated DC-DC conversion with digital isolation in a single package, eliminating the need for separate isolated power supplies and digital isolators. It sits within the power management IC hierarchy, specifically under isolated power converters, and is essential for systems that require signal and power isolation for safety, noise immunity, or ground loop elimination. Key features of the ADP1031ACPZ-2 include a wide input voltage range, three isolated outputs (one flyback, one inverting, one buck), and seven digital isolator channels with data rates up to 100 kbps. The device operates over the industrial temperature range of -40°C to +125°C and is available in a 41-lead LFCSP (9x7 mm) package. The ADP1031ACPZ-2 variant specifically provides a 5.0V output on the buck regulator, as indicated by the '2' suffix. The ADP1031 uses a high-frequency flyback architecture with integrated power switches, achieving high efficiency and small form factor. The digital isolators use iCoupler technology, providing reliable isolation up to [DATA_NEEDED: isolation voltage] with low propagation delay. The device includes soft-start, overcurrent protection, and thermal shutdown for robust operation. Typical applications include industrial fieldbus systems, programmable logic controllers (PLCs), isolated sensor interfaces, and motor drive control circuits. The ADP1031ACPZ-2 is particularly suited for systems requiring isolated SPI communication and multiple isolated power rails, such as data acquisition systems and industrial automation. When designing with this device, ensure proper PCB layout for isolation barrier spacing and use recommended transformer and capacitor values from the datasheet. The input supply should be decoupled with low-ESR ceramic capacitors, and the isolated outputs should be filtered to meet ripple requirements.
ADP1031ACPZ-3-RL7 - Isolated PMU with 7 Digital Isolators | Analog Devices
The ADP1031ACPZ-3-RL7 is a high performance, isolated micropower management unit (PMU) from Analog Devices that integrates an isolated flyback dc-to-dc regulator, an inverting dc-to-dc regulator, and a buck dc-to-dc regulator to provide three isolated power rails. Additionally, it contains four high speed serial peripheral interface (SPI) digital isolators and three general-purpose digital isolators, making it a complete isolated power and data solution in a single 41-lead LFCSP (9x7 mm) package. This device is designed for applications requiring galvanic isolation and multiple regulated outputs, such as industrial process control, isolated data acquisition, and power supply monitoring. An isolated micropower management unit (PMU) is a power management IC that integrates multiple DC-DC converters and digital isolators to provide isolated power and signal transfer across an isolation barrier. It combines the functions of a flyback converter, an inverting converter, and a buck converter, along with digital isolators, into a single package. This integration reduces board space, simplifies design, and improves reliability compared to discrete solutions. The ADP1031 belongs to the family of isolated power management ICs, which are essential in systems requiring safety isolation, noise immunity, and multiple isolated supply rails. Key features of the ADP1031ACPZ-3-RL7 include a wide input voltage range, three isolated outputs (one positive, one negative, and one buck), and integrated digital isolators with up to 100 Mbps data rate. The device operates from a 4.5V to 60V input supply, making it suitable for industrial 24V buses and other high-voltage rails. The flyback regulator provides an isolated output up to 3.3V or 5V, the inverting regulator provides a negative output down to -5V, and the buck regulator provides a positive output down to 3.3V. The digital isolators provide reinforced isolation up to 5 kV rms, ensuring safe signal transfer across the isolation barrier. Technically, the ADP1031 uses a proprietary architecture that combines a primary-side flyback controller with secondary-side regulation, achieving high efficiency and low EMI. The device includes overvoltage protection (OVP) on the inverting regulator, which monitors the FB3 pin and stops switching if the voltage falls below VFB3 by 10%. This protects downstream circuitry from excessive negative voltages. The device also features soft-start, short-circuit protection, and thermal shutdown, ensuring robust operation in harsh environments. Typical applications include isolated data acquisition systems, industrial PLCs, motor control, and power monitoring. The ADP1031 is ideal for systems that require isolated power and data transfer, such as isolated SPI communication between a microcontroller and an ADC. Its integrated digital isolators eliminate the need for separate isolator ICs, reducing component count and board space. When designing with the ADP1031, ensure proper PCB layout with adequate spacing for isolation, and place decoupling capacitors close to the power pins. The device requires an external transformer for the flyback converter, and the selection of the transformer is critical for efficiency and isolation rating. Refer to the datasheet for recommended transformer specifications and layout guidelines.
ADP1048ARQZ-R7 - Digital PFC Controller, 400kHz, 24-QSOP | ADI
The Analog Devices ADP1048ARQZ-R7 is a digital power factor correction (PFC) controller with accurate AC power metering and inrush current control, housed in a 24-lead QSOP package. The device is specifically designed for interleaved and bridgeless PFC topologies in ac/dc systems, supporting switching frequencies from 30 kHz to 400 kHz with average current mode control. A Power Factor Correction controller is a specialized power management IC that shapes the input current drawn from the AC mains to be in phase with the input voltage, thereby maximizing the ratio of real power to apparent power. PFC controllers sit at the front end of ac/dc converters, between the input rectifier bridge and the bulk capacitor, and they form the first stage of the power supply hierarchy: PFC stage -> DC-DC converter -> point-of-load regulators -> powered loads. By maintaining a high power factor (typically > 0.99), PFC controllers reduce harmonic distortion, help systems meet regulatory standards such as IEC 61000-3-2, and improve overall energy efficiency in servers, telecom rectifiers, and industrial power supplies. Key features of the ADP1048ARQZ-R7 include programmable switching frequency up to 400 kHz, accurate AC power metering capability via an integrated digital engine, inrush current control to limit stress on the bulk capacitor during AC plug-in events, and a digital interface for parameter adjustment. The 24-lead QSOP package offers a compact footprint and supports surface-mount assembly with reflow soldering compatible with standard lead-free profiles. The digital PFC core implements a conventional boost topology with average current mode control, providing stable operation across a wide line and load range. The architecture combines a high-performance analog front end for current and voltage sensing with a digital controller that closes the PFC loop via a programmable algorithm. This digital approach enables per-design tuning without external component changes, simplifies BOM consolidation across product variants, and provides telemetry for input power, RMS current, RMS voltage, and power factor that the system host can read back through the I2C/PMBus-compatible interface. The ADP1048 is the interleaved/bridgeless sibling of the ADP1047, which targets single-phase PFC stages. Typical applications include high-efficiency ac/dc power supplies for servers and networking equipment, telecom rectifiers complying with 80 PLUS and ENERGY STAR programs, industrial SMPS front ends, UPS battery chargers, and interleaved/bridgeless PFC stages for 1 kW to 5 kW power ranges. When designing with the ADP1048ARQZ-R7, ensure the I2C address is correctly configured in the EEPROM and that the sense resistor in the inductor return path has sufficient bandwidth for the programmed switching frequency to maintain stable average-current control.
ADP225ACPZ - Dual 300mA Adj LDO, Low Noise, High PSRR | ADI
The Analog Devices ADP225ACPZ is a dual-channel, 300 mA adjustable-output, low-dropout (LDO) linear regulator in an 8-lead LFCSP-UD (2 mm × 2 mm) package. Each output rail can be set from 0.5 V to 5.0 V, and the part accepts input voltages from 2.5 V to 5.5 V with a typical dropout of 170 mV at 300 mA load. An LDO (low-dropout) linear regulator is a class of voltage regulator whose category (LM-IC) maintains a stable, accurate rail even when VIN approaches VLOOOW - i.e. the regulator continues to regulate with only a few hundred millivolts of headroom. In the broader power-tree hierarchy, an LDO sits downstream of switching DC-DC converters (which provide bulk step-down) and upstream of noise-sensitive loads; LDOs trade efficiency for clean output because no switching noise reaches the load. Key features include high power-supply rejection ratio (PSRR) for downstream ripple attenuation, low output noise suitable for RF and audio rails, integrated quick-output discharge (QOD) transistors that actively pull each output to ground when disabled, and stable operation with only 1 µF, ±30% ceramic output capacitors. The two channels are independently enabled and share a common input. The ADP225ACPZ is fabricated on a BiCMOS process that combines CMOS control logic with bipolar pass elements, achieving both low quiescent current and excellent transient response. The QOD MOSFETs prevent output voltage drift into the disabled state, which is critical for power-sequenced loads such as RF transceivers, FPGAs, and image sensors. Typical applications include portable and battery-powered devices (smartphones, wearables, tablets), wireless handsets and RF transceivers, image sensor and camera-module rails, FPGA/ASIC I/O and core supplies in low-voltage domains, and any space-constrained board that needs two clean rails from a single small package. When designing with this part, ensure the input supply has sufficient bulk capacitance to handle the simultaneous turn-on of both outputs and that the 1 µF minimum output capacitance requirement is met across temperature and DC bias. The exposed pad must be soldered to a sufficient copper pour for thermal dissipation.
ADP2360ACPZ-5.0-R7 - 60V, 50mA Synchronous Buck Regulator | Analog Devices
The Analog Devices ADP2360ACPZ-5.0-R7 is a high-efficiency, high-input-voltage, discontinuous-conduction-mode (DCM) synchronous step-down DC-to-DC switching regulator that delivers a fixed 5.0V output at up to 50mA continuous load current. Housed in an 8-lead LFCSP (Lead Frame Chip Scale Package) with an exposed pad, the device operates over a wide 4.5V to 60V input voltage range, making it ideal for regulating power from industrial 24V/48V rails, automotive batteries, and high-impedance loop sources in space-constrained applications. A buck (step-down) switching regulator is a DC-to-DC converter that uses an internal switch, an inductor, and a rectifier to transfer energy from input to output at a duty cycle that sets the output voltage below the input. Synchronous buck regulators replace the external Schottky rectifier with an internal low-side MOSFET, which improves efficiency at light loads and shrinks the bill of materials. The ADP2360 specifically uses a single-pulse pulse-frequency-modulation (PFM) architecture with adjustable peak-current control, minimizing both input and output ripple while allowing the designer to optimize efficiency for the application's operating conditions and minimize the compatible inductor size. Key features of the ADP2360ACPZ-5.0-R7 include a fixed 5.0V output (no external feedback resistors required), wide 4.5V to 60V input operating range, up to 50mA continuous output current, adjustable peak current limit via an external resistor, integrated P-channel high-side switch and N-channel low-side switch, internal soft-start, and a power-good (PG) output that indicates when VOUT is within regulation. The 8-pin LFCSP exposed-pad package provides a low thermal-resistance path and a compact footprint for industrial sensor modules, factory-automation nodes, and battery-powered remote transmitters. The PFM control topology is well suited to low-duty-cycle, light-load applications because it skips switching cycles when the output is in regulation, holding quiescent current to a minimum. A power-good flag simplifies interface to downstream microcontrollers and enables sequenced multi-rail power-up. The device is specified for operation from -40C to +125C junction temperature and is qualified for automotive and harsh-environment use cases. Typical applications include 4-20mA current-loop powered sensor transmitters, industrial process-control loops, automotive body and sensor electronics, battery-powered remote telemetry, and isolated low-power bias supplies. The high input-voltage tolerance allows direct connection to 24V industrial buses or 12V/24V automotive rails without pre-regulation. When designing with the ADP2360ACPZ-5.0-R7, choose the input capacitor, output capacitor, and inductor per the datasheet's selection tables to maintain stable DCM operation. A small ceramic input capacitor is typically sufficient because the PFM architecture draws input current only during the high-side switch on-time; the exposed pad must be soldered to a thermal land on the PCB for proper heat dissipation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet alone.
ADP2360ACPZ-R7 - 60V 50mA Synchronous Step-Down DC-DC | Analog Devices
The Analog Devices ADP2360ACPZ-R7 is a high efficiency, high input voltage, synchronous step-down DC-DC switching regulator with 4.5V to 60V input range and 50 mA continuous output current capability, housed in an 8-pin LFCSP EP (exposed pad) package. Operating in discontinuous conduction mode (DCM), the ADP2360 is engineered for 4-20 mA industrial loop-powered applications and similar space-constrained designs where high input voltage and low quiescent current matter. A synchronous buck (step-down) DC-DC converter is a switching regulator topology that uses MOSFET switches to chop an input voltage and an LC filter to reconstruct a lower, well-regulated DC rail. DCM operation means the inductor current returns to zero each switching cycle, eliminating reverse-current losses and enabling high efficiency at light loads - a critical attribute when the source current itself is capped at a few milliampere. Key features include 60V maximum input voltage with built-in over-voltage protection, 4.5V minimum input for cold-start, an adjustable output from 0.8V to VIN, internal high-side and low-side synchronous MOSFETs, and 100 percent duty-cycle capability for low-dropout pass-through. The regulator requires only an inductor and small ceramic capacitors, simplifying BOM and shrinking the footprint. The architecture integrates a peak-current-mode controller with DCM boundary detection, a precision reference, and internal soft-start. The exposed pad (EP) of the LFCSP-8 package provides a low thermal resistance path (about 36 C/W) for the small 50 mA load it serves, ensuring reliable operation across -40C to +125C junction temperatures. Typical applications include 4-20 mA current-loop powered field transmitters, industrial sensors, smart meters, isolated industrial interface modules, low-power analog front-end bias rails, battery-powered industrial monitors, and remote telemetry nodes. The wide VIN tolerance also suits 24V, 36V, and 48V industrial buses. When designing with the ADP2360ACPZ-R7, size the inductor for the peak current boundary at your worst-case load and use low-ESR ceramic input/output capacitors to keep ripple below your analog front-end noise budget. The exposed pad must be soldered to a sufficiently large copper pour for proper thermal dissipation. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes not found in the standalone ADP2360 datasheet, giving engineers an actionable reference for sourcing and design-in.
ADP2370ACPZ-R7 - 800mA, 15V Buck DC-DC Converter | Analog Devices
The Analog Devices ADP2370ACPZ-R7 is a high efficiency, low quiescent current, 800 mA synchronous step-down (buck) DC-to-DC converter housed in an 8-lead, 3 mm x 3 mm LFCSP (QFN) exposed-pad package. It operates from a 3.2 V to 15 V input range, delivers an adjustable output from 0.8 V to 14 V, and uses a current-mode architecture with internal MOSFET switches that require only three tiny external components. The switching frequency is selectable between 600 kHz and 1.2 MHz via the FSEL pin, or it can be synchronized to an external 600 kHz to 1.2 MHz clock. A buck (step-down) DC-DC converter is a switching voltage regulator that uses an inductor, a switch, and a rectifier to convert a higher input voltage to a lower output voltage with high efficiency. The buck converter sits within the broader hierarchy of DC-DC converters -> switching regulators -> voltage regulators -> power management ICs -> semiconductors. By cycling the internal MOSFETs at high frequency and filtering with an LC network, a buck converter achieves efficiencies typically above 90 percent, vastly superior to linear regulators at large input-to-output voltage differentials. Key features of the ADP2370 include up to 800 mA of continuous output current, 92 percent peak efficiency at 1.2 MHz operation, low quiescent current for extended battery life, internal compensation, internal soft start, power-good output, and thermal shutdown. The device integrates high-side and low-side MOSFETs, eliminating the need for external switching transistors. Forced PWM (FPWM) mode maintains a constant switching frequency for noise-sensitive applications, while automatic PWM/PFM mode maximizes efficiency at light loads. The ADP2370 uses peak current-mode control with internal slope compensation, providing excellent line and load transient response across the full operating range. The internal reference is a high-accuracy bandgap with low temperature coefficient. Power-good indication, undervoltage lockout, and overcurrent protection are all integrated, reducing external component count to three (input capacitor, inductor, output capacitor). The exposed pad on the LFCSP-8 package provides a low thermal resistance path, enabling full 800 mA output even in compact designs. Typical applications include portable and battery-powered equipment, handheld instrumentation, point-of-load regulators for FPGAs, DSPs, and microcontrollers, automotive infotainment and telematics subsystems (non-safety-critical rails), industrial control boards, and distributed power systems. The wide 3.2 V to 15 V input range accommodates single-cell Li-ion, USB, 5 V and 12 V rails, making the device particularly versatile for mixed-rail designs. When designing with the ADP2370, select an inductor with low DCR to preserve efficiency and keep the input/output ceramic capacitors close to the IC to minimize parasitic inductance. For noise-sensitive analog loads, operate in FPWM mode to avoid PFM switching ripple; for battery-powered systems, leave PFM enabled to maximize efficiency at light load. The exposed pad must be soldered to a sufficient copper pour for thermal dissipation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Verified distributor data is current as of 2026-10-06, and all specifications come from the Analog Devices ADP2370/ADP2371 datasheet.
ADP3335ARMZ-3.3 - 500mA anyCAP LDO, 3.3V Fixed | Analog Devices
The Analog Devices ADP3335ARMZ-3.3 is a 500 mA, 3.3 V fixed-output, high-accuracy anyCAP low-dropout (LDO) linear regulator housed in an 8-pin MSOP package. It operates from a 2.6 V to 12 V input rail and delivers up to 500 mA continuous load current with a typical dropout of 200 mV at full load, while achieving ±0.9% initial accuracy at 25°C and ±1.8% accuracy over line, load, and temperature. What is an LDO? An LDO (low-dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage, typically with a dropout of only a few hundred millivolts. LDOs belong to the broader category of linear regulators, which in turn sit under voltage regulators inside the power management IC hierarchy. Because they dissipate excess voltage as heat rather than switching it, LDOs introduce no switching noise, making them ideal for powering noise-sensitive analog and RF loads. The anyCAP architecture used by the ADP3335 family allows stable operation with any good-quality output capacitor - including low-ESR ceramic MLCC types - which simplifies board layout and shrinks the BOM in space-constrained designs. Key features include an ultralow quiescent current that extends battery life in portable equipment, an ultralow dropout of 200 mV at 500 mA, integrated thermal shutdown and current-limit protection, and a noise performance optimized for wireless and instrumentation applications. The device is specified over the extended -40°C to +85°C (junction to +150°C) operating range, suiting industrial environments. The ADP3335 uses an enhanced bipolar process and a precision bandgap reference that drives an internal PNP pass element. The anyCAP loop compensation removes the ESR-related stability constraints of legacy LDOs, allowing designers to use small 1 µF to 10 µF ceramic capacitors at the output without compromising phase margin. This combination of low noise, tight accuracy, and ceramic-cap stability is unusual for a 500 mA part and is a hallmark of the ADP33xx family. Typical applications include wireless handsets, notebook and palmtop computers, PCMCIA cards, barcode scanners, low-noise analog circuits, and battery-powered instrumentation requiring a clean 3.3 V rail. The wide 2.6 V–12 V input range also supports 5 V and 9 V system buses, and the low dropout margin permits one-cell Li-ion discharge down to ~3.5 V before regulation is lost. When designing with this part, place input and output capacitors as close to the IC as possible and ensure the PCB copper under the exposed pad (if present) provides adequate thermal relief - continuous 500 mA into a 5 V input from 12 V dissipates 4.35 W. The fixed -3.3 suffix means no external feedback resistors are required, reducing BOM cost and layout area versus adjustable LDOs.
ADR421BRZ - 2.5V Ultraprecision Low Noise Voltage Reference | Analog Devices
The Analog Devices ADR421BRZ is an ultraprecision, low-noise, 2.500 V XFET voltage reference IC delivering ±0.04% initial accuracy, 1.75 µV p-p noise (0.1 Hz to 10 Hz), and 3 ppm/°C maximum temperature coefficient in an 8-pin SOIC package (R-8). It provides up to 10 mA of source current from a 4.5 V to 18 V input supply, with 70 ppm/mA load regulation and 35 ppm/V line regulation. An XFET voltage reference is a specialized series-mode reference that uses an externally modulated JFET pair to generate a temperature-compensated bandgap-like voltage, achieving lower noise and better long-term stability than conventional buried-Zener references. It occupies the product hierarchy of voltage reference -> series reference -> precision reference -> power management IC, serving as the stable potential against which ADCs, DACs, and precision analog signal chains are calibrated. Key features include sub-2 µV p-p low-frequency noise, 50 ppm/1000 hrs long-term stability, 40 ppm typical hysteresis, and a wide 4.5 V to 18 V supply operating range with low quiescent current. The XFET architecture also eliminates the need for a resistor in series with the supply pin required by older Zener designs, simplifying PCB layout and improving turn-on settling. Architecturally, the XFET cell pairs a JFET reference transistor with a second JFET biased to cancel temperature drift. A precision op-amp servos the bandgap-like cell to maintain constant VOUT, while the trim network programs the initial accuracy. This topology trades the higher pre-trim noise of bandgap references for far better long-term drift and thermal hysteresis. Typical applications include precision 16-bit and 24-bit ADC and DAC reference inputs, industrial process control calibration, automatic test equipment (ATE) system references, and precision data acquisition systems in medical imaging, weighing scales, and 6.5-digit digital multimeters. The 2.5 V output makes it an ideal companion to devices such as the AD8628, AD8629, and ADI's AD57xx, AD76xx, and ADuM-series converter families. When designing with the ADR421BRZ, route the output node directly to the reference pin of the target converter with a 0.1 µF ceramic plus 1 µF tantalum bypass network within 5 mm of the reference pin to preserve noise and load regulation. Avoid running digital or switching traces under the reference - injected charge can deteriorate 0.1 Hz to 10 Hz noise performance. This page synthesizes distributor pricing across nine channels, parametric drop-in alternatives, and practical layout notes not consolidated on the manufacturer datasheet.
ADR421BRZ-REEL7 - 2.5V Ultraprecision XFET Voltage Reference | Analog Devices
The Analog Devices ADR421BRZ-REEL7 is an ultraprecision, low-noise 2.500 V XFET voltage reference IC delivering up to 10 mA output current in an 8-pin SOIC package, supplied on a 7-inch reel for high-volume SMT assembly. It features an initial accuracy of ±0.04% (B-grade), 3 ppm/°C temperature coefficient, 1.75 µV p-p noise (0.1 Hz to 10 Hz), and 50 ppm/1000-hour long-term stability, with an operating input range of 4.5 V to 18 V. A voltage reference is a precision circuit that produces a stable, known DC voltage independent of supply variations, temperature, and load current. Voltage references sit at the base of the signal chain in data acquisition, instrumentation, and precision analog systems: their absolute accuracy and noise floor set the ultimate performance limit of downstream ADCs, DACs, sensor bridges, and weighing scales. The ADR421 belongs to the XFET (eXtra implanted junction FET) family, which uses a junction FET reference cell rather than a buried Zener or bandgap to achieve sub-2 µV p-p noise and excellent thermal hysteresis of 40 ppm typical. Key features include 4.5 V to 18 V supply range, low supply current of 0.5 mA typical, line regulation of 35 ppm/V, load regulation of 70 ppm/mA, and -40 °C to +125 °C operating temperature. The SOIC-8 (R-8) package is the industry-standard precision reference footprint, allowing direct substitution on most reference layouts. Unlike buried-Zener references that need 10 V minimum, the XFET architecture operates from as low as 4.5 V, suiting it to 5 V and ±5 V or +5 V/-12 V system rails. The ADR421 is offered in three grades (A: ±0.05%, B: ±0.04%, C: ±0.12%) and three packages (8-lead SOIC, 8-lead MSOP, TO-92). Typical applications include precision data acquisition system references, high-resolution ADC and DAC reference inputs, industrial process control calibration, precision weighing scales, medical instrumentation, and instrumentation amplifiers. The 2.500 V output matches the full-scale range of many 16-bit and 24-bit sigma-delta ADCs (e.g., AD7799/AD7730 families) and is compatible with 5 V reference-input DACs. When designing with the ADR421, add a 0.1 µF ceramic bypass capacitor close to the supply pin and a 1 µF to 10 µF tantalum or ceramic capacitor on the output for stable load-transient response. The trim pin (pin 5) allows ±0.5% fine adjustment of the output using a 10 kΩ/1 kΩ divider; leave it open if trimming is not required. This page synthesizes distributor pricing, drop-in same-brand and cross-brand alternatives, and practical design notes not found in the manufacturer datasheet alone.
ADR4525BRZ-R7 - 2.5V Ultra-Low Noise Voltage Reference | Analog Devices
The ADR4525BRZ-R7 is a high precision, low power, low noise series voltage reference from Analog Devices, providing a fixed 2.5V output with ±0.02% maximum initial error (B grade). Housed in an 8-pin SOIC (SOIC-8) package, this device delivers up to 10 mA output current and operates over a wide supply range, making it ideal for precision data acquisition, industrial process control, and medical instrumentation. A voltage reference is a precision electronic component that produces a constant output voltage regardless of load, supply variations, or temperature. It serves as a stable benchmark for analog-to-digital converters (ADCs), digital-to-analog converters (DACs), and comparators, ensuring measurement accuracy. Voltage references are categorized into series and shunt types; the ADR4525 is a series reference, which offers lower power consumption and better accuracy than shunt references. Within the power management hierarchy, voltage references are essential building blocks in precision analog systems, bridging the gap between raw power supplies and the stable voltages required by sensitive circuitry. Key features of the ADR4525BRZ-R7 include ultra-low output noise (1.4 µV p-p typical from 0.1 Hz to 10 Hz), excellent temperature stability (2 ppm/°C typical), and a low dropout voltage. The device also features a wide operating temperature range of -40°C to +125°C, making it suitable for harsh environments. Its high accuracy and low noise are achieved through an innovative core topology that minimizes thermal and noise errors. Technically, the ADR4525 uses a bandgap-based architecture with precision laser-trimmed resistors to achieve its tight initial accuracy. The output is buffered to provide low output impedance and fast transient response. The device is fully specified over the industrial temperature range and is available in tape and reel packaging (R7 suffix) for automated assembly. Typical applications include precision data acquisition systems, high-resolution ADCs and DACs, industrial process control, medical devices, and portable instrumentation. The low noise and high accuracy make it particularly well-suited for reference buffering in 16-bit and higher resolution converters. When designing with the ADR4525BRZ-R7, ensure adequate decoupling on the input and output pins with 0.1 µF and 1 µF capacitors, respectively, to maintain stability and minimize noise. The output can source up to 10 mA, but for higher current loads, an external buffer is recommended.
ADT7475ARQZ-REEL - 4-Fan PWM Thermal Controller | onsemi
The onsemi ADT7475ARQZ-REEL is a dBCool remote thermal monitor and four-fan PWM controller designed for active cooling in noise-sensitive or power-sensitive equipment. The verified distributor listing specifies a -40°C to 125°C temperature-monitor range, internal and external sensor support, SMBus output, and a 16-QSOP package. Its core role is to combine thermal monitoring with closed-loop fan control rather than relying on fixed-speed cooling. A remote thermal monitor and fan controller is a power-management and thermal-management IC that measures temperature and regulates cooling equipment according to configured thresholds. In the hierarchy, it belongs to system monitoring and fan-control ICs, which sit below broader thermal-management and power-management systems. The ADT7475 supports one on-chip temperature sensor and two remote temperature-sensor diode channels, enabling distributed temperature measurement in a compact controller. Key verified features include control and monitoring for up to four fans, high- and low-frequency fan-drive signals, an SMBus output, and an extended temperature-measurement range extending to 191°C as stated in indexed descriptions of the manufacturer datasheet. These features allow designers to combine local package-temperature protection with remote-diode monitoring while using variable-speed fans to reduce acoustic noise and power consumption. The controller measures and controls fan speed for thermal regulation, making it applicable to computer servers, storage systems, communications equipment, industrial controllers, and other multi-fan platforms. Its internal sensor and remote-diode inputs can support different thermal zones, while PWM output enables gradual fan-speed changes instead of abrupt full-speed operation. The 16-QSOP surface-mount package is suitable for compact production boards. A key design consideration is validating remote-diode electrical characteristics, sensor placement, fan-drive polarity, and SMBus configuration against the manufacturer datasheet. Because the provided search data does not expose exact timing, voltage, current, resolution, or absolute-maximum values for every parameter, those details are marked as needed rather than inferred. This page combines verified distributor facts, official-datasheet findings, and explicit engineering data gaps. Unlike a simple fan switch, the ADT7475ARQZ-REEL adds active temperature feedback and programmable fan-speed control, helping systems balance thermal margin against fan noise and power. This synthesis is intended to support component selection, schematic planning, and qualified drop-in replacement research.
ADUM3190ARWZ - 2.5kV Isolated Error Amplifier | Analog Devices
The ADUM3190ARWZ is a high-stability isolated error amplifier from Analog Devices, designed for isolated voltage feedback in power supplies. It integrates a precision reference and an error amplifier with an isolated output, providing a 2.5 kV RMS isolation rating. The device operates from a single 3.0 V to 20 V supply on the primary side and features a 400 mV reference with ±1% accuracy. It is available in a 16-lead SOIC-W package, making it suitable for space-constrained designs. An isolated error amplifier is a specialized analog IC that transfers an error signal across an isolation barrier without using an optocoupler. It typically includes a precision reference, an error amplifier, and an isolation channel (often based on iCoupler technology) to provide a feedback signal that is galvanically isolated from the output. This component is essential in isolated DC-DC converters and switching power supplies where the feedback path must cross the isolation boundary while maintaining accuracy and stability. Key features of the ADUM3190ARWZ include a 2.5 kV RMS isolation rating, a 400 mV reference with ±1% accuracy, and a wide operating temperature range of -40°C to +125°C. The device offers a typical gain bandwidth of 400 kHz and a quiescent current of 1.2 mA, enabling efficient operation in power management circuits. Its high stability ensures reliable performance over temperature and time, making it ideal for industrial and automotive power systems. Technically, the ADUM3190ARWZ uses Analog Devices' iCoupler technology to achieve isolation, which provides superior performance compared to optocoupler-based solutions, including better temperature stability and longer lifespan. The error amplifier has a transconductance output that can be compensated with external components to optimize loop stability. The device also includes an internal reference that can be used for voltage regulation, simplifying the external circuit. Typical applications include isolated DC-DC converters, offline power supplies, and isolated voltage sensing in motor drives and battery management systems. The device is particularly suited for applications requiring precise voltage regulation across an isolation barrier, such as telecom and server power supplies. When designing with the ADUM3190ARWZ, ensure proper PCB layout to maintain isolation creepage and clearance distances. The feedback loop compensation should be designed according to the datasheet guidelines to achieve stable operation. The device is RoHS compliant and available in tape and reel packaging.
ADUM3191ARWZ - Isolated Error Amplifier | Analog Devices
The ADUM3191ARWZ is an isolated error amplifier from Analog Devices, designed for feedback control in isolated power supplies. It integrates a precision error amplifier with an isolated PWM signal path, providing a compact solution for voltage regulation across an isolation barrier. The device operates from a single 3.0V to 20V supply and features a 400mV reference, making it suitable for a wide range of industrial and automotive applications. An isolated error amplifier is a specialized analog IC that amplifies the difference between a feedback voltage and a reference, then transmits the error signal across an isolation barrier without a direct electrical connection. This is essential in isolated power converters where the primary and secondary sides must be galvanically isolated for safety and noise immunity. The ADUM3191ARWZ uses Analog Devices' iCoupler technology to achieve this isolation, eliminating the need for optocouplers and their associated aging and nonlinearity issues. Key features of the ADUM3191ARWZ include a 2.5kVrms isolation rating, a 400mV reference with ±1% accuracy, and a bandwidth of 200kHz. The device supports an input voltage range of 3.0V to 20V and operates over the industrial temperature range of -40°C to +125°C. The SOIC-8 package is compact and industry-standard, facilitating easy integration into existing designs. The ADUM3191ARWZ is built on Analog Devices' proprietary iCoupler technology, which uses chip-scale transformers to transmit signals across the isolation barrier. This approach provides superior performance compared to optocouplers, including higher reliability, faster response, and better temperature stability. The device also includes an internal compensation network, simplifying the external circuit design. Typical applications include isolated DC-DC converters, offline power supplies, and motor drives. In these systems, the ADUM3191ARWZ provides accurate voltage feedback while maintaining galvanic isolation, improving system safety and performance. Its high bandwidth and low propagation delay make it suitable for high-frequency switching converters. When designing with the ADUM3191ARWZ, ensure proper PCB layout to maintain isolation creepage and clearance distances. The device requires a bypass capacitor on the primary side and careful attention to the feedback loop compensation to ensure stability.
ADUM3220ARZ - 4A Dual-Channel Isolated Gate Driver | Analog Devices
The ADUM3220ARZ is a 4 A dual-channel isolated gate driver from Analog Devices, based on the proprietary iCoupler technology. It combines high-speed CMOS and monolithic transformer isolation to provide robust, isolated drive for power transistors such as MOSFETs and IGBTs. The device is housed in an 8-lead SOIC package (8-SOIC, 0.154" width) and offers a 2500 Vrms isolation rating, making it suitable for applications requiring galvanic isolation between control and power stages. Isolated gate drivers are essential components in power electronics systems where the control circuitry must be electrically isolated from the high-voltage power stage. They transmit switching signals across an isolation barrier while providing sufficient drive current to charge and discharge the gate capacitance of power switches. The ADUM3220ARZ integrates the isolation and driver functions in a single IC, eliminating the need for external pulse transformers and simplifying PCB design. Key features of the ADUM3220ARZ include a 4 A peak output current, precise timing with a maximum propagation delay of 60 ns, and channel-to-channel matching of 5 ns. It operates over a wide supply voltage range and supports high junction temperatures up to 125°C. The device is RoHS compliant and lead-free, meeting modern environmental standards. The ADUM3220ARZ uses iCoupler technology, which employs chip-scale transformers to achieve isolation. This approach offers superior performance compared to optocouplers, including higher data rates, lower power consumption, and better timing accuracy. The driver's output stages are designed to deliver high peak current for fast switching, reducing switching losses in power converters. Typical applications include isolated switch-mode power supplies, motor drives, solar inverters, and industrial automation systems. The ADUM3220ARZ is particularly well-suited for driving IGBTs and MOSFETs in half-bridge or full-bridge configurations, where its dual-channel architecture and precise timing ensure reliable operation. When designing with the ADUM3220ARZ, it is important to provide adequate decoupling on the input and output supplies and to minimize parasitic inductance in the gate drive loop. Proper PCB layout is critical to achieve the specified timing and isolation performance.
ADUM3220ARZ-RL7 - Isolated 4A Dual Gate Driver | Analog Devices
The ADUM3220ARZ-RL7 is a dual-channel, isolated gate driver from Analog Devices, delivering 4 A peak output current per channel. It is based on the proprietary iCoupler technology, which combines high-speed CMOS and monolithic transformer isolation to provide reliable galvanic isolation up to 2500 Vrms. The device is housed in a compact 8-SOIC package (0.154", 3.90mm width), making it suitable for space-constrained power conversion designs. An isolated gate driver is a specialized integrated circuit that amplifies control signals from a low-voltage controller to drive power transistors (such as MOSFETs and IGBTs) while providing electrical isolation between the control side and the power stage. This isolation protects sensitive logic circuits from high-voltage transients and ground loops, which is essential in applications like motor drives, switch-mode power supplies, and solar inverters. The ADUM3220ARZ-RL7 belongs to the family of digital isolators and gate drivers, sitting between simple level shifters and more complex isolated power supplies. Key features of the ADUM3220ARZ-RL7 include a 4 A peak output current, a maximum propagation delay of 60 ns, and a channel-to-channel matching of 5 ns. These precise timing characteristics ensure synchronized switching of power devices, reducing switching losses and electromagnetic interference. The device also supports high junction temperature operation, making it robust for industrial environments. Its 2500 Vrms isolation rating meets the requirements of many safety standards, and it is RoHS compliant and lead-free. From a technical perspective, the ADUM3220ARZ-RL7 uses a monolithic transformer to couple signals across the isolation barrier, offering superior performance compared to optocouplers in terms of speed, reliability, and power consumption. The driver features a nominal UVLO (undervoltage lockout) of 4.1 V, ensuring that the output stage is fully enabled only when the supply voltage is adequate. This prevents erratic behavior during power-up and brownout conditions. The dual-channel configuration allows driving both high-side and low-side switches in a half-bridge topology with a single device. Typical applications include isolated DC-DC converters, motor control inverters, and power supplies for industrial and automotive systems. The ADUM3220ARZ-RL7 is particularly well-suited for applications requiring high-speed switching and robust isolation, such as server power supplies and renewable energy inverters. When designing with this device, it is important to provide adequate decoupling on the input and output supplies and to follow the recommended layout guidelines to minimize parasitic inductance. The propagation delay and matching specifications should be considered when designing dead-time for half-bridge circuits to prevent shoot-through current.
ADUM3221ARZ - Isolated 4A Dual-Channel Gate Driver | Analog Devices
The ADUM3221ARZ is an isolated, 4 A dual-channel gate driver from Analog Devices, based on the iCoupler technology. It combines high-speed CMOS and monolithic transformer technology to provide galvanic isolation between the input and each output, enabling voltage translation and eliminating the need for separate isolation components. The device is available in an 8-SOIC package and is designed for driving power MOSFETs and IGBTs in various power conversion applications. A gate driver is a power amplifier that accepts a low-power input from a controller IC and produces a high-current drive input for the gate of a power transistor. In isolated gate drivers, the input and output are galvanically isolated, protecting the low-voltage control circuitry from high-voltage transients and ground loops. The ADUM3221ARZ provides two independent isolation channels, each capable of sourcing and sinking 4 A peak current, making it suitable for driving large capacitive loads with fast switching speeds. Key features of the ADUM3221ARZ include a maximum propagation delay of 60 ns, channel-to-channel matching of 5 ns, and a 4.1 V nominal under-voltage lockout (UVLO) threshold. The device operates over a wide supply voltage range and supports high junction temperatures, making it robust for industrial applications. The iCoupler technology ensures reliable isolation with a 2500 Vrms isolation rating, meeting safety requirements for many power systems. The ADUM3221ARZ is designed for use in isolated DC-DC converters, motor drives, and power inverters. Its high peak output current and fast propagation delay enable efficient switching of power transistors, reducing switching losses and improving system efficiency. The device also features a wide operating temperature range, making it suitable for harsh environments. When designing with the ADUM3221ARZ, it is important to ensure proper PCB layout to minimize parasitic inductance and maintain signal integrity. The input and output supplies should be adequately decoupled with ceramic capacitors placed close to the pins. The device's UVLO feature ensures that the gate driver remains disabled until the supply voltage is sufficient, preventing erratic operation during power-up. Overall, the ADUM3221ARZ is a reliable and high-performance isolated gate driver that simplifies the design of isolated power systems while providing excellent electrical performance and robustness.
ADUM3221ARZ-RL7 - Isolated 4A Dual-Channel Gate Driver | Analog Devices
The ADUM3221ARZ-RL7 is a dual-channel, isolated gate driver from Analog Devices, delivering 4A peak output current per channel. It is based on the iCoupler® technology, which combines high-speed CMOS and monolithic transformer isolation to provide superior performance compared to traditional pulse transformer and gate driver combinations. The device is housed in an 8-lead SOIC package and provides 2500Vrms isolation, making it suitable for applications requiring galvanic isolation between control and power stages. An isolated gate driver is a specialized integrated circuit that provides the necessary voltage and current to drive the gate of power transistors (such as MOSFETs and IGBTs) while maintaining electrical isolation between the low-voltage control side and the high-voltage power side. This isolation is critical for safety and noise immunity in applications like motor drives, power inverters, and switch-mode power supplies. The ADUM3221ARZ-RL7 integrates two independent isolation channels, each capable of sourcing and sinking 4A, enabling direct driving of high-power switches without additional buffer stages. Key features of the ADUM3221ARZ-RL7 include a 4.1V nominal undervoltage lockout (UVLO) threshold, which ensures reliable operation during power-up and brown-out conditions. The device supports a wide supply voltage range on the output side, typically from 4.5V to 18V, allowing compatibility with various gate drive voltages. The propagation delay is typically 48ns, and the device offers a minimum pulse width of 100ns, enabling high-frequency switching up to 1MHz. The isolation barrier is rated for 2500Vrms, with a common-mode transient immunity (CMTI) of 25kV/µs, ensuring robust operation in noisy environments. The ADUM3221ARZ-RL7 is designed for high-performance applications where isolation and drive strength are critical. Its 4A peak output current can directly drive large MOSFETs and IGBTs, reducing the need for external buffer circuits. The dual-channel configuration allows for driving half-bridge or full-bridge topologies with a single device, simplifying PCB layout and reducing component count. The device also features a dead-time control input, enabling precise timing between high-side and low-side switches to prevent shoot-through currents. Typical applications include isolated switch-mode power supplies, motor drives, solar inverters, and industrial automation systems. The device is also suitable for automotive applications, such as electric vehicle (EV) charging systems and on-board chargers, where isolation and reliability are paramount. The ADUM3221ARZ-RL7 is available in tape and reel packaging (RL7 suffix), with a standard quantity of 1000 units per reel, facilitating automated assembly. When designing with the ADUM3221ARZ-RL7, it is essential to provide adequate decoupling capacitors on both the input and output supply pins to ensure stable operation. The input side (VDD1) and output side (VDD2) are isolated, and each requires a bypass capacitor of at least 0.1µF placed close to the respective pins. Additionally, the dead-time control pin (DT) should be connected to a resistor to set the desired dead time, or tied to VDD1 for a fixed dead time. Proper PCB layout with a solid ground plane on the output side is recommended to minimize parasitic inductance and ensure clean switching.
ADUM3223ARWZ-RL7 - 4A Isolated Half-Bridge Gate Driver | Analog Devices
The ADUM3223ARWZ-RL7 is a 4 A isolated, half-bridge gate driver from Analog Devices that employs iCoupler technology to provide independent and isolated high-side and low-side outputs. It offers 3000 V rms isolation in a narrow body, 16-lead SOIC package, making it suitable for a wide range of power conversion applications. The device features 4 A peak output current, 2 channels, and a wide supply voltage range, ensuring robust driving capability for power MOSFETs and IGBTs. An isolated gate driver is a specialized integrated circuit that provides the necessary voltage and current to switch power transistors while maintaining galvanic isolation between the control side and the power stage. This isolation is critical in applications where high voltages or ground potential differences exist, protecting low-voltage control circuitry and ensuring safe operation. The ADUM3223 belongs to the family of digital isolators and gate drivers, which are essential components in modern power electronics systems. Key features of the ADUM3223ARWZ-RL7 include 4 A peak output current, 3000 V rms isolation rating, 2 independent channels, and a propagation delay of typically 50 ns. The device operates from a supply voltage range of 4.5 V to 18 V on the secondary side, and 3.0 V to 5.5 V on the primary side, providing flexibility in system design. The iCoupler technology ensures reliable signal transfer across the isolation barrier with high noise immunity and low power consumption. Technically, the ADUM3223 integrates a high-speed CMOS interface with a magnetic isolation barrier, enabling fast and accurate signal transmission. The device supports a maximum switching frequency of 1 MHz, making it suitable for high-frequency power converters. The output stage is designed to drive capacitive loads with minimal rise and fall times, reducing switching losses in the power stage. Typical applications include isolated switch-mode power supplies, motor drives, solar inverters, and industrial automation systems. The device's high output current and isolation capability make it ideal for driving power MOSFETs and IGBTs in half-bridge and full-bridge topologies. Its compact SOIC-16 package allows for space-efficient PCB layouts. When designing with the ADUM3223, it is important to ensure proper decoupling of the supply pins and to minimize parasitic inductance in the gate drive loop. The device's propagation delay and timing skew should be considered for high-frequency operation to avoid shoot-through in half-bridge configurations.
ADUM3224ARWZ - 4A Isolated Half-Bridge Driver | Analog Devices
The ADUM3224ARWZ is a 4 A isolated precision half-bridge gate driver from Analog Devices, employing iCoupler technology to provide independent and isolated high-side and low-side outputs. It is housed in a narrow-body 16-lead SOIC package and offers 3000 V rms isolation, making it suitable for automotive and industrial applications where galvanic isolation is required between the control and power stages. An isolated gate driver is a device that transfers switching signals across an isolation barrier, typically using capacitive or magnetic coupling, to control power transistors such as MOSFETs and IGBTs. It ensures that the high-voltage power stage is electrically isolated from the low-voltage control circuitry, protecting sensitive logic and enabling safe operation in noisy environments. The ADUM3224 belongs to the family of isolated gate drivers, which are essential components in power conversion systems like motor drives, inverters, and switch-mode power supplies. Key features of the ADUM3224ARWZ include a 4 A peak output current, which provides fast and robust gate charging for large power switches, and a wide supply voltage range of 4.5 V to 18 V for the output stage. The device also features a propagation delay of 48 ns (typical) and a minimum pulse width of 50 ns, enabling high-frequency switching. Its 3000 V rms isolation rating ensures reliable operation in high-voltage applications, and it is AEC-Q100 qualified for automotive use. Technically, the ADUM3224 uses Analog Devices' iCoupler technology, which integrates micro-transformers to achieve isolation, offering superior performance compared to optocouplers in terms of speed, reliability, and power consumption. The driver supports a wide operating temperature range of -40°C to +125°C, making it suitable for harsh environments. Its CMOS inputs are compatible with standard logic levels, simplifying interface design. Typical applications include isolated switch-mode power supplies, motor control inverters, and automotive systems such as electric vehicle (EV) traction inverters and on-board chargers. The ADUM3224ARWZ is also used in industrial automation and renewable energy systems where robust isolation and high current drive are critical. When designing with this device, ensure proper PCB layout to minimize parasitic inductance in the gate drive loop, and place decoupling capacitors close to the VDD and VDDA pins. The input side operates from a 3.0 V to 5.5 V supply, while the output side can be powered from 4.5 V to 18 V, allowing flexible interface with various controllers and power stages.