CP2102N-A01-GQFN28 vs CP2102N-A02-GQFN28R Vergleich
Detaillierter Direktvergleich von CP2102N-A01-GQFN28 von Silicon Labs und CP2102N-A02-GQFN28R von Silicon Labs. Vergleichen Sie die wichtigsten Spezifikationen, elektrischen Parameter, Gehäuse, Lebenszyklusstatus, Preise und Verfügbarkeit, um das beste Bauteil für Ihre Designanforderungen zu ermitteln.
Silicon Labs
CP2102N-A01-GQFN28 - USB to UART Bridge QFN-28 | Silicon Labs (Tape & Reel)
CP2102N-A01-GQFN28 ✓ AktivSilicon Labs
CP2102N-A02-GQFN28R USB-to-UART Bridge, QFN28 | Silicon Labs (Tape & Reel)
CP2102N-A02-GQFN28R ✓ AktivSpezifikationsvergleich
| Parameter | CP2102N-A01-GQFN28 | CP2102N-A02-GQFN28R |
|---|---|---|
| Marke | Silicon Labs | Silicon Labs |
| Kategorie | Interface ICs | Interface ICs |
| Lebenszyklusstatus | Aktiv | Aktiv |
| Lagerstatus | In Stock | In Stock |
| Stückpreis (USD) | $2,31 | $2,35 |
| Product Type | USB to UART Bridge Controller | — |
| Series | USBXpress | — |
| USB Standard | USB 2.0 Full-Speed (12 Mbps) | — |
| UART Interface | USB 2.0 UART | — |
| Number of UART Channels | 1 | — |
| Datenrate | 300 baud to 1 Mbaud | — |
| Supply Voltage (VBUS) | 4.0 V to 5.25 V | — |
| Supply Voltage (VDD) | 3.0 V to 3.6 V | 3 V to 3.6 V |
| Internal Regulator Output | 3.3 V (up to ~100 mA) | 3.3 V |
| Betriebstemperatur | -40 C to +85 C | -40C to +85C |
| Gehäuse | 28-QFN (5x5 mm) with exposed pad | QFN-28 (5x5 mm) |
| Montageart | Surface Mount | Surface Mount |
| GPIO | Yes (multiple, signal-configurable) | — |
| Reset Pin | RSTb (active-low hardware reset) | — |
| On-chip Oscillator | Yes (no external crystal required) | — |
| MSL-Level | MSL3 (per JEDEC J-STD-020) | — |
| RoHS-Status | Compliant | Compliant |
| Host Driver | Silicon Labs CP210x VCP driver | — |
| Funktion | — | USB 2.0 to UART Bridge Controller |
| Protocol | — | USB 2.0 Full-Speed |
| I/O Voltage (VIO) | — | 1.8 V to VDD |
| Maximum Baud Rate | — | 3 Mbaud |
| USB Speed | — | Full-Speed (12 Mbps) |
| Digital I/O Pins | — | 7 |
| Internal Regulator Current | — | Up to 100 mA (external load) |
| Internal Oscillator | — | 48 MHz (no external crystal required) |
| ROM for Descriptors | — | 960 bytes (one-time programmable) |
| UART Data Bits | — | 5, 6, 7, or 8 (programmable) |
| Hardware Flow Control | — | RTS/CTS supported |