EPC16UC88T vs EPC16UC88 Vergleich
Detaillierter Direktvergleich von EPC16UC88T von Altera und EPC16UC88 von Altera. Vergleichen Sie die wichtigsten Spezifikationen, elektrischen Parameter, Gehäuse, Lebenszyklusstatus, Preise und Verfügbarkeit, um das beste Bauteil für Ihre Designanforderungen zu ermitteln.
Spezifikationsvergleich
| Parameter | EPC16UC88T | EPC16UC88 |
|---|---|---|
| Marke | Altera | Altera |
| Kategorie | EEPROM | Memory ICs |
| Lebenszyklusstatus | Letzte Kaufgelegenheit | Unknown |
| Lagerstatus | In Stock | In Stock |
| Stückpreis (USD) | $9,95 | $0,00 |
| Speichertyp | Non-volatile Flash configuration PROM (in-system programmable) | — |
| Memory Density | 16 Mbit (2,097,152 x 8 bits) | — |
| Configuration Interface | Serial (4-wire: nCS, DCLK, DATA, nINIT_CONF_DONE) | — |
| Maximum DCLK Frequency | 33 MHz | — |
| Supply Voltage (VCC) | 3.0 V to 3.6 V (3.3 V nominal) | — |
| Betriebstemperaturbereich | -40 C to +85 C (industrial) | — |
| Gehäuse | 88-ball UBGA, 11 mm x 8 mm | 88-UBGA (11x8) |
| In-System Programming | IEEE Std 1149.1 (JTAG) | — |
| Cascade Support | Yes (for higher density multi-PROM chains) | — |
| MSEL Compatibility | FPP / PS configuration modes (3.3 V legacy) | — |
| Compatible FPGA Families | Cyclone, Cyclone II, Stratix, Stratix II, Stratix III, Stratix IV, Arria GX | — |
| Family Density Step | Largest member of EPC4 / EPC8 / EPC16 family | — |
| RoHS-Status | [DATA_NEEDED: RoHS] | [DATA_NEEDED: RoHS status] |
| MSL-Level | [DATA_NEEDED: MSL] | — |
| Lead-Free / Halogen-Free | [DATA_NEEDED: lead-free status] | — |
| Open-Drain nINIT_CONF_DONE | Yes | — |
| Device Type | — | In-system programmable configuration PROM for FPGAs |
| Configuration Memory Capacity | — | 16 Mb |
| Versorgungsspannung | — | 3.3 V core and I/O |
| Package Family | — | UBGA |
| In-System Programmability | — | IEEE Std. 1532 compatible |
| Programming Language Support | — | Jam Standard Test and Programming Language (STAPL) |
| JTAG Boundary Scan | — | Supported |
| nINIT_CONF Function | — | Allows private JTAG instruction to start FPGA configuration |
| Configuration Architecture | — | Configuration controller and flash memory |
| FPGA Configuration Use | — | Automatic configuration after power-up or system initialization |
| Data Output | — | Configuration data output controlled by OE and nCS |
| Output Control | — | OE and nCS control tri-state buffer and address counter |
| Montageart | — | Surface mount |
| Package Dimensions | — | 11 mm x 8 mm |
| REACH Status | — | [DATA_NEEDED: REACH status] |
| Betriebstemperatur | — | [DATA_NEEDED: operating temperature] |
| Output Current | — | [DATA_NEEDED: output current] |
| Configuration Frequency | — | [DATA_NEEDED: configuration frequency] |
| AEC-Q100 Qualification | — | [DATA_NEEDED: AEC-Q100 qualification] |