MAX3483ESA+ vs SN65HVD37D Vergleich
Detaillierter Direktvergleich von MAX3483ESA+ von Maxim Integrated und SN65HVD37D von Texas Instruments. Vergleichen Sie die wichtigsten Spezifikationen, elektrischen Parameter, Gehäuse, Lebenszyklusstatus, Preise und Verfügbarkeit, um das beste Bauteil für Ihre Designanforderungen zu ermitteln.
Texas Instruments
SN65HVD37D - 3.3V Full-Duplex RS-485 Transceiver | TI (Tape & Reel)
SN65HVD37D ✓ AktivSpezifikationsvergleich
| Parameter | MAX3483ESA+ | SN65HVD37D |
|---|---|---|
| Marke | Maxim Integrated | Texas Instruments |
| Kategorie | Interface ICs | Interface ICs |
| Lebenszyklusstatus | Aktiv | Aktiv |
| Product Type | RS-485/RS-422 transceiver | — |
| Versorgungsspannung | 3.3 V | — |
| Verified Supply Range | 3 V to 3.6 V | — |
| Maximum Data Rate | 10 Mbps | — |
| Driver and Receiver Count | 1 driver and 1 receiver | — |
| Duplex Mode | Half-duplex | — |
| Interface Standards | RS-485 and RS-422 | — |
| Driver Architecture | Slew-rate limited | — |
| EMI Control | Slew-rate limitation reduces EMI and reflections | — |
| Low-Speed Error-Free Transmission | Up to 250 kbps | — |
| Power Architecture | 3.3V-powered, low-power transceiver | — |
| Gehäuse | 8-SOIC | 14-SOIC (D), 0.154" / 3.90 mm width |
| Montageart | Surface mount | Surface Mount |
| Operating Voltage | 3 V to 3.6 V | — |
| ESD Protection | [DATA_NEEDED: ESD protection rating for MAX3483ESA+] | — |
| Betriebstemperaturbereich | [DATA_NEEDED: operating temperature range] | — |
| Versorgungsstrom | [DATA_NEEDED: supply current] | — |
| Receiver Output Type | [DATA_NEEDED: receiver output type] | — |
| Termination Requirement | [DATA_NEEDED: termination and biasing details] | — |
| RoHS-Status | [DATA_NEEDED: RoHS status] | — |
| REACH Status | [DATA_NEEDED: REACH status] | — |
| AEC-Q100 Qualification | [DATA_NEEDED: AEC-Q100 qualification] | — |
| Lead-Free Status | [DATA_NEEDED: lead-free status] | — |
| Halogen-Free Status | [DATA_NEEDED: halogen-free status] | — |
| Device Type | — | Transceiver (1 driver / 1 receiver) |
| Protocol | — | RS-422, RS-485 |
| Number of Drivers/Receivers | — | 1 / 1 |
| Duplex | — | Full |
| Supply Voltage (VCC) | — | 3 V to 3.6 V (nominal 3.3 V) |
| Signaling Rate | — | Up to 25 Mbps |
| Receiver Unit Load | — | 1/8 unit load (up to 256 nodes) |
| Bus-Pin ESD Protection (HBM) | — | >15 kV HBM |
| Receiver Hysteresis | — | 60 mV (typical) |
| Quiescent Current (active) | — | 1 mA (typical) |
| Standby / Shutdown Current | — | <1 uA (typical) |
| Betriebstemperatur | — | -40 C to +85 C |
| RoHS / Lead-Free | — | RoHS compliant, lead-free (per TI product page) |
| Fail-Safe Receiver | — | Yes (idle/open/short safe) |
| Driver / Receiver Enable | — | Independent DE and RE pins |