74LVC1G00GW - Single 2-Input NAND Gate, 1.65V-5.5V | Nexperia
Teilenummer: 74LVC1G00GW ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $0.12 | $0,12 |
| 10 | $0.1 | $1,00 |
| 100 | $0.08 | $8,00 |
| 500 | $0.06 | $30,00 |
| 1.000 | $0.045 | $45,00 |
| 3.000 | $0.035 | $105,00 |
74LVC1G00GW Übersicht
An LVC (Low-Voltage CMOS) gate is a sub-family of advanced CMOS logic optimized for operation below 5 V while remaining tolerant of 5 V input signals. Within the broader logic hierarchy, the 74LVC1G00 sits inside the single-gate 74LVC1G family, which in turn belongs to Nexperia's 74LVC logic IC portfolio for power-efficient portable, industrial, and computing designs. Unlike legacy HC/T families, LVC combines low static power consumption with high noise immunity and JEDEC-compliant interface thresholds.
Key features include Schmitt-trigger inputs that tolerate slow or noisy edges, ±24 mA balanced output drive (VCC = 3.0 V) for direct LED or bus loading, latch-up performance exceeding 250 mA per JEDEC JESD78, CMOS low static power consumption, and IOFF partial-power-down support that prevents back-feed currents when the device is unpowered but signal lines remain live. Inputs accept 3.3 V or 5 V logic levels, allowing the part to act as a down-translator in mixed-voltage systems without external level-shifters.
Typical applications span portable and battery-powered electronics, mobile phones and wearables, level shifting between 5 V microcontrollers and 3.3 V peripherals, general-purpose glue logic on FPGA and ASIC boards, and interface buffering in industrial control and white-goods modules. The compact 5-pin TSSOP footprint enables placement near connectors and signal sources for short, clean traces.
When designing with this device, always observe the absolute-maximum VCC of 6.5 V and derate output current above VCC = 4.5 V. Place a 0.1 µF decoupling capacitor as close as possible to VCC pin 5, and unused inputs must be tied to VCC or GND to prevent floating-input quiescent current. The TSSOP-5 footprint is mechanically compatible with Nexperia's entire 74LVC1Gxx single-gate family, simplifying BOM consolidation.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page alone, giving the engineer a single reference for sourcing and second-sourcing decisions.
Drop-in-Alternativen für 74LVC1G00GW – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit 74LVC1G00GW (gleiche Bauform und Footprint) – abweichend in Logic Family, Package, Operating Temperature, Supply Voltage (VCC), Input Type.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
74LVC1G00GW,165
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
74LVC1G00GV,125
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
74AHC1G00GW,125
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
SN74LVC1G00DBVR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
74LVC1G00SE-7
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
74LVC1G00
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
74LVC1G00GW Grenzwerte & elektrische Eigenschaften
| Gate Type | NAND |
| Number of Gates | 1 |
| Number of Inputs per Gate | 2 |
| Logic Family | 74LVC (Low-Voltage CMOS) |
| Supply Voltage (VCC) | 1.65 V to 5.5 V |
| Input Voltage Tolerance | Up to 5.5 V (3.3 V or 5 V drive capable) |
| Output Drive Current | ±24 mA (VCC = 3.0 V) |
| Propagation Delay (tpd) | 10.5 ns (typical) |
| Input Type | Schmitt-trigger |
| Static Current (ICC) | 10 µA (max) |
| IOFF Support | Yes (partial-power-down safe) |
| Latch-up Performance | Exceeds 250 mA (per JEDEC JESD78) |
| Betriebstemperatur | -40 °C to +125 °C |
| Gehäuse | TSSOP-5 (SOT-353 / UMT5) |
| Montageart | Surface Mount |
| RoHS-Status | Compliant |
| MSL-Level | 1 (unlimited) |
74LVC1G00GW Pin-Konfiguration
| Pin 1 | 1A — Data input A (Schmitt-trigger) |
| Pin 2 | 1B — Data input B (Schmitt-trigger) |
| Pin 3 | GND — Ground (0 V) |
| Pin 4 | 1Y — Data output Y (= NOT (1A AND 1B)) |
| Pin 5 | VCC — Supply voltage (1.65 V to 5.5 V) |
Typische Anwendungen
74LVC1G00GW ist geeignet für 6 Anwendungs: Mixed-Voltage Level Translation (5V to 3.3V), Portable and Battery-Powered Electronics, FPGA / ASIC Glue Logic on Evaluation Boards, Industrial Control and White-Goods Modules, Computing and Server Peripherals (IOFF Safe Insertion), LED Driving and Front-Panel Logic.
Mixed-Voltage Level Translation (5V to 3.3V)
The 74LVC1G00GW is purpose-built for mixed-voltage translation because its inputs accept 3.3 V or 5 V drive while its output swings rail-to-rail at the local VCC. With VCC = 3.3 V and a 5 V CMOS source on input A or B, the gate cleanly down-translates a 5 V high level to 3.3 V logic at output Y. This eliminates external resistor dividers or dedicated level-shifters in 5 V MCU to 3.3 V peripheral interfaces such as SPI, I2C buffers, or GPIO handshaking, and the Schmitt-trigger inputs reject the slow edges typical of long PCB traces or capacitive loads.
Empfohlen
Portable and Battery-Powered Electronics
The 74LVC1G00GW's 1.65 V minimum supply, sub-µA quiescent current, and ±24 mA drive make it ideal for portable devices running from a single Li-ion cell (3.0-4.2 V) or two AA cells (2.0-3.2 V). It can implement logic inversion, basic state decoding, or reset conditioning without burdening the battery budget. The TSSOP-5 package keeps the board footprint under 3 mm², leaving room for the smallest wearables, BLE beacons, or wireless sensor nodes where every µA and every mm² matters.
Empfohlen
FPGA / ASIC Glue Logic on Evaluation Boards
FPGAs, SoCs, and high-pin-count ASICs almost always need one or two discrete logic gates for reset conditioning, watchdog pulse stretching, clock gating, or hand-shaking between domains. The 74LVC1G00GW delivers that single NAND function with 1.65-5.5 V compatibility, allowing it to sit between the FPGA bank (often 1.8 V) and a 3.3 V peripheral without level-shifter ICs. Its 10.5 ns tpd adds negligible delay to control paths while the small TSSOP-5 footprint places it next to the FPGA without rerouting dense BGA breakouts.
Empfohlen
Industrial Control and White-Goods Modules
Industrial PLCs, HVAC controllers, motor-driver boards, and white-goods modules require logic that survives -40 °C to +125 °C, noisy switching environments, and long cable harnesses. The 74LVC1G00GW's Schmitt-trigger action tolerates slow or noisy input edges typical of opto-isolated sensor inputs or relay-coil transients, while JEDEC-compliant latch-up immunity exceeds 250 mA. Its wide 1.65-5.5 V supply lets a single part service 3.3 V logic islands and 5 V sensor interfaces on the same board, reducing BOM complexity.
Empfohlen
Computing and Server Peripherals (IOFF Safe Insertion)
Hot-swap, hot-plug, and partial-power-down applications in servers, storage backplanes, and removable-card interfaces need logic that does not back-feed current when its VCC rail is collapsed but the signal line is still driven. The 74LVC1G00GW's IOFF specification guarantees that output leakage stays in the µA range during partial-power-down, protecting upstream devices and meeting the requirements of modern OR-ing and bus-isolation topologies. Its balanced ±24 mA drive can directly switch power-good LEDs or status indicators.
Empfohlen
LED Driving and Front-Panel Logic
The ±24 mA output drive at VCC = 3.0 V lets the 74LVC1G00GW sink or source a small indicator LED directly without a series driver transistor, simplifying front-panel logic on consumer devices and appliances. By using a NAND gate instead of a simple inverter, the engineer can implement blink patterns, fault latches, or status-AND logic in a single IC. The TSSOP-5 footprint sits next to the LED without crowding the front-panel flex, and the part's 5 V tolerance protects against back-feeds from external connectors.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für 74LVC1G00GW – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | 74LVC1G00GW,165 | 74LVC1G00GV,125 | 74AHC1G00GW,125 | SN74LVC1G00DBVR | 74LVC1G00SE-7 | 74LVC1G00 (SGMICRO) |
|---|---|---|---|---|---|---|---|
| Brand | Nexperia | Nexperia | Nexperia | Nexperia | Texas Instruments | Diodes Incorporated | SGMC |
| Package | TSSOP-5 (SOT-353) | TSSOP-5 (SOT-353) | SC-74 (SOT-753) | TSSOP-5 (SOT-353) | SOT-23-5 (DBV) | SOT-353 (TSSOP-5) | TSSOP-5 (SOT-353) |
| Supply Voltage Range | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 2.0 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V |
| Output Drive Current | ±24 mA (VCC = 3.0 V) | ±24 mA | ±24 mA | ±8 mA | ±24 mA | ±24 mA | ±24 mA |
| Schmitt-trigger Inputs | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| IOFF Partial-Power-Down | Yes | Yes | Yes | No | Yes | Yes | Yes |
| Operating Temperature | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C |
Wichtigste Unterscheidungsmerkmale
- Industry-standard TSSOP-5 Nexperia pinout (vs. SN74LVC1G00DBVR (TI SOT-23-5))
- Wide 1.65 V to 5.5 V supply supports battery-direct operation (vs. 74AHC1G00GW (AHC family))
- IOFF partial-power-down safe for hot-swap designs (vs. 74AHC1G00GW (no IOFF))
Designhinweise
Place a 0.1 µF X7R ceramic decoupling capacitor as close as possible to the VCC pin (pin 5), keeping the trace short and wide to minimize inductance. Use a ground via adjacent to pin 3 (GND) to provide a low-impedance return path. For TSSOP-5 (SOT-353) land patterns, follow the JEDEC MO-193 footprint: pad pitch 0.65 mm, pad width 0.3-0.4 mm. Avoid routing noisy switching traces under the IC; keep digital inputs short or series-terminated to prevent reflections that the Schmitt-trigger can mask but not eliminate.
Do not leave unused NAND inputs floating - tie each unused input to VCC or GND through a low-impedance path to prevent shoot-through current and unstable output. Do not exceed the absolute maximum VCC of 6.5 V; transients from hot-plug events or inductive loads must be clamped. Above VCC = 4.5 V, derate output current per the datasheet curve. The 74LVC1G00GW is not a buffered-output variant - if you need a three-state output, use the 74LVC1G125GW instead.
Schmitt-trigger inputs give hysteresis of typically 0.5-0.9 V, allowing reliable operation with input rise/fall times up to several hundred ns. However, very slow edges combined with capacitive loading can still cause output oscillation; if rise times exceed 200 ns, add a small series resistor (100 Ω) at the input or accelerate the edge upstream. For long PCB traces carrying 5 V signals into a 3.3 V VCC domain, place the gate within 50 mm of the source to limit radiated emissions and crosstalk.
Compliance-Informationen
RoHS and lead-free per Nexperia product page; JEDEC JESD78 latch-up exceeds 250 mA. AEC-Q100 grade requires dedicated -Q1 suffix variant; the standard 74LVC1G00GW is commercial/industrial grade.
