AD8002ARZ - 600MHz Dual Amp | Analog Devices | 8-SOIC
Teilenummer: AD8002ARZ ✓ AktivAD8002ARZ Übersicht
A current-feedback amplifier is a voltage-feedback amplifier subclass in which bandwidth and stability behavior depend partly on the feedback resistor rather than solely on closed-loop gain. Current-feedback amplifiers are frequently used where high speed, controlled gain, and drive capability must coexist. In the broader electronics hierarchy, the AD8002ARZ is an operational amplifier, signal-conditioning amplifier, and analog semiconductor intended for high-frequency video and data-conversion signal paths.
The AD8002ARZ features low differential gain error of 0.01% and differential phase error of 0.02°. Its gain flatness is 0.1 dB through 60 MHz, while settling to 0.1% takes 16 ns. These characteristics make the device suitable for video buffering, analog-to-digital converter interfaces, instrumentation, and other wideband systems requiring rapid signal transitions and low amplitude and phase distortion.
Analog Devices describes the AD8002 as a dual amplifier with transimpedance linearization circuitry. That architecture helps maintain differential gain and phase performance when driving video loads, including the 150-ohm load conditions cited in the manufacturer data sheet. The device operates from dual ±5 V supplies, providing a straightforward implementation for professional video, broadcast, industrial imaging, and test-and-measurement systems that already use positive and negative rails.
Typical applications include composite and component video amplification, high-speed ADC input conditioning, active filtering, and general-purpose high-speed signal processing. In a video path, the amplifier can preserve signal amplitude and phase relationships across a broad frequency range. For data converters, its 600 MHz bandwidth and 16 ns settling time can reduce timing margin when the source impedance, feedback network, and trace topology are controlled correctly.
Design should begin with the manufacturer pinout and feedback-network guidance, because current-feedback amplifiers require careful resistor selection and impedance control. Keep feedback-loop routing compact, use low-inductance interconnections, and account for amplifier input and output parasitics when operating close to the device's bandwidth. Power-supply bypass capacitance should be placed close to the supply pins, with the return path arranged to minimize high-frequency loop area.
This page combines manufacturer specifications, package and lifecycle information, practical circuit guidance, and structured comparisons for engineers evaluating the AD8002ARZ. It also identifies the available same-family order options while clearly separating confirmed drop-in options from functionally similar parts that require separate engineering review.
Drop-in-Alternativen für AD8002ARZ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
AD8002AR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
AD8002ARZ-R7
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
AD8002ARZ-RL
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
AD8002ARZ Grenzwerte & elektrische Eigenschaften
| Product Type | Dual current-feedback amplifier |
| Number of Amplifier Channels | 2 circuits |
| Small-Signal Bandwidth at Gain +1 | 600 MHz |
| Small-Signal Bandwidth at Gain +2 | 500 MHz |
| Slew Rate | 1200 V/us |
| Settling Time to 0.1% | 16 ns |
| Maximum Supply Current | 5.0 mA per amplifier |
| Maximum Power Consumption | 50 mW per amplifier |
| Differential Gain Error | 0.01% |
| Differential Phase Error | 0.02 degrees |
| Gain Flatness | 0.1 dB through 60 MHz |
| Versorgungsspannung | +/-5 V |
| Reference Video Load | 150 ohm |
| Gehäuse | 8-SOIC |
| Montageart | Surface mount |
| Production Status | Production |
AD8002ARZ 8-soic Pinbelegungsleitfaden
Pinbelegung für AD8002ARZ (8-soic-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für AD8002ARZ.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
AD8002ARZ ist geeignet für 6 Anwendungs: Composite Video Signal Conditioning, High-Speed ADC Input Interface, Professional Video Distribution, Active Video Filtering, High-Speed Instrumentation Buffer, Industrial Imaging Signal Path.
Composite Video Signal Conditioning
The AD8002ARZ fits composite video amplification because it combines 600 MHz bandwidth at gain +1 with 0.1 dB gain flatness through 60 MHz. The Analog Devices AD8002 Data Sheet (Rev. E) identifies 0.01% differential gain error, 0.02-degree differential phase error, and 150-ohm video-load capability. Placing the amplifier close to the source reduces trace loss before the signal reaches routing and distribution circuitry. The design should use the manufacturer's feedback network and keep output routing short to limit parasitic capacitance, which is important at this bandwidth.
High-Speed ADC Input Interface
AD8002ARZ is suitable for conditioning signals entering high-speed analog-to-digital converters when wide bandwidth and fast settling are required. Its 600 MHz bandwidth at gain +1 and 16 ns settling to 0.1% provide timing margin around the sampling aperture, while 0.01% differential gain error helps limit amplitude conversion error. The amplifier should be placed adjacent to the converter or connector, with short high-impedance input routing and a controlled feedback resistor. Supply bypassing and ground-return layout must prevent converter switching activity from modulating the input signal.
Professional Video Distribution
The dual AD8002ARZ can provide two independent wideband channels for professional video distribution or monitoring equipment operating from ±5 V rails. Each channel offers 500 MHz bandwidth at gain +2 and 1200 V/us slew rate, allowing large-amplitude video transitions to remain fast and controlled. Gain flatness of 0.1 dB through 60 MHz and differential phase error of 0.02 degrees support faithful signal reproduction. Practical layouts should use short output paths, local decoupling, and controlled source and load impedances to prevent reflections or unintended high-frequency peaking.
Active Video Filtering
AD8002ARZ can implement active filtering stages in wideband video and instrumentation systems where conventional low-bandwidth op amps would limit signal bandwidth. Its 600 MHz gain +1 bandwidth, 1200 V/us slew rate, and 50 mW maximum power consumption per amplifier provide a useful combination of speed and efficiency. Component tolerances, resistor parasitics, and capacitor self-resonance should be selected to keep the intended response. Because current-feedback topology depends on feedback impedance, stage values and stability margins should be calculated from the manufacturer's guidance rather than transferred directly from a voltage-feedback design.
High-Speed Instrumentation Buffer
The AD8002ARZ is useful as a wideband instrumentation buffer when preserving fast transient information is more important than minimizing power. A 500 MHz bandwidth at gain +2 and 16 ns settling to 0.1% allow the device to follow rapidly changing signals with limited amplitude error. The dual configuration provides independent channels for differential or multi-node measurements. Source impedance must remain compatible with the selected feedback network, and the input stage should avoid long probe or cable paths that introduce inductance and capacitance before the amplifier's input pins.
Industrial Imaging Signal Path
AD8002ARZ fits industrial imaging and sensor-interface circuits that process high-bandwidth analog signals while keeping amplifier power modest. Each channel is specified for 5.0 mA maximum supply current and 50 mW maximum power consumption per amplifier, which can simplify thermal planning in multi-channel systems. The 600 MHz bandwidth and 1200 V/us slew rate help preserve pulse edges, while the low gain and phase errors support calibrated amplitude and timing relationships. Place the amplifier near the sensor interface, use short differential or single-ended routes as appropriate, and decouple each supply rail at the device.
Technische Referenzdaten für AD8002ARZ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | AD8002AR | AD8002ARZ-R7 | AD8002ARZ-RL |
|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Channels | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Topology | Current-feedback amplifier | Current-feedback amplifier | Current-feedback amplifier | Current-feedback amplifier |
| Bandwidth at Gain +1 | 600 MHz | 600 MHz | 600 MHz | 600 MHz |
| Bandwidth at Gain +2 | 500 MHz | 500 MHz | 500 MHz | 500 MHz |
Wichtigste Unterscheidungsmerkmale
- High bandwidth for a dual low-power amplifier (vs. AD8002AR)
- Exact same-family pin and package compatibility (vs. AD8002ARZ-R7)
- No performance penalty from the reel ordering code (vs. AD8002ARZ-RL)
Designhinweise
Keep the feedback resistor, feedback trace, input connection, and output route physically short because parasitic inductance and capacitance can alter the bandwidth and stability of a 600 MHz current-feedback amplifier. Route the feedback loop away from high-current and digital signals, use a continuous ground reference, and avoid sharing long return paths with switching circuitry. The 16 ns settling specification is meaningful only when the physical feedback network and source/load impedances match the test conditions used by Analog Devices.
Place low-inductance bypass capacitors directly across each device supply pin and connect them to the quiet ground reference without long loops. The AD8002 operates from ±5 V supplies, so both positive and negative rails require local decoupling. Account for the datasheet limit of 5.0 mA supply current per amplifier when sizing the rail regulators and return paths. Decoupling capacitors should have suitable self-resonance and effective high-frequency characteristics rather than relying solely on nominal capacitance.
Do not copy feedback values from a voltage-feedback amplifier into the AD8002 circuit without recalculation. The current-feedback topology makes bandwidth and stability dependent on the feedback impedance and source impedance. Also avoid adding capacitance to the input or output unless its effect on stability and bandwidth has been checked. Use the manufacturer's recommended resistor values and gain configurations, then validate the final board across the required temperature and supply ranges.
For video and converter interfaces, preserve controlled impedance and minimize discontinuities between the source, amplifier, and load. Terminate transmission lines according to the system architecture, keep connectors away from sensitive amplifier pins, and verify clock or data synchronization independently from analog bandwidth. The low specified gain and phase errors are valuable, but system-level distortion can still be dominated by reflections, unequal propagation paths, or poorly controlled source impedances.
Compliance-Informationen
The manufacturer identifies the AD8002 family as being in production. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated in the cited manufacturer snippets and remain unknown.