AD9260AS - 16-Bit 2.5 MSPS CMOS ADC | Analog Devices
Teilenummer: AD9260AS ✓ AktivAD9260AS Übersicht
An ADC converts continuous analog voltages into digital words for processing, storage, transmission, or control. The AD9260 belongs to the oversampling ADC family and uses an 8-times oversampling ratio to achieve high dynamic range over a broad input bandwidth. This places it in the semiconductor hierarchy of data converters, analog-to-digital converters, and signal-chain integrated circuits, where it can serve as the bridge between an analog front end and downstream digital logic.
The principal features include 16-bit resolution, a 2.5 MHz output word rate, advanced CMOS construction, and an 8-times oversampling architecture. The single +5 V supply simplifies system power planning, while the scaling circuit provides a path to lower power consumption when the required clock and data rates are reduced. The industrial-temperature version and 44-pin MQFP package support robust equipment designs requiring a conventional surface-mount interface.
Internally, the oversampling architecture uses analog and digital filtering characteristics to improve conversion performance relative to the sampling rate. The converter requires careful treatment of its analog input, clock, supply, and digital output paths. Because converter performance depends on signal-chain balance, reference behavior, clock jitter, and output-impedance loading, layout and component selection can be as important as the nominal converter specifications.
Typical uses include communications equipment, instrumentation, industrial measurement, medical signal acquisition, and embedded processing systems. In each case, AD9260AS is useful when a compact 16-bit conversion stage is needed at a 2.5 MHz word rate without moving to a substantially more complex parallel-output architecture.
Design around the 44-pin MQFP footprint using the manufacturer pin-description table, and place the supporting input, clock, and decoupling networks according to the recommended application circuit. Keep high-speed digital traces short, provide a controlled return path, and verify the analog input bandwidth and settling behavior for the intended source impedance.
This page organizes the confirmed AD9260AS specifications, package information, sourcing questions, verified drop-in relationships, application guidance, and engineering design notes. It also distinguishes documented device characteristics from parameters that must be confirmed in the manufacturer datasheet before layout or production release.
Drop-in-Alternativen für AD9260AS – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
AD9260ASZ
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
AD9260ASRL
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
AD9260AS Grenzwerte & elektrische Eigenschaften
| Converter Type | 16-bit high-speed oversampling ADC |
| Auflösung | 16 bit |
| Output Word Rate | 2.5 MHz |
| Oversampling Ratio | 8x |
| Versorgungsspannung | +5 V |
| Typical Power Consumption | 550 mW |
| Minimum Scalable Power Consumption | 150 mW at reduced clock and data rates |
| Process Technology | Advanced CMOS |
| Gehäuse | 44-pin MQFP, 10 x 10 mm |
| Montageart | Surface mount |
| RoHS-Status | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
AD9260AS 44-pin mqfp, 10 x 10 mm Pinbelegungsleitfaden
Pinbelegung für AD9260AS (44-pin mqfp, 10 x 10 mm-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für AD9260AS.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
AD9260AS ist geeignet für 6 Anwendungs: Communications Receiver, Industrial Signal Acquisition, Medical Monitoring Equipment, Precision Instrumentation, Audio and Waveform Capture, Embedded Control and Monitoring.
Communications Receiver
AD9260AS suits communications receiver front ends that require 16-bit conversion at a 2.5 MHz output word rate. Its 8-times oversampling architecture supports high dynamic range over a wide bandwidth, while the single +5 V supply simplifies receiver-board power planning. Place the converter after the RF mixer or channel-filter network, and design the clock and parallel output routing to prevent timing degradation. The principal benefit is the combination of a 16-bit digital word and a conventional 44-pin MQFP interface; the design trade-off is that a 2.5 MHz word rate may not match newer high-rate converter architectures.
Empfohlen
Industrial Signal Acquisition
AD9260AS is appropriate for industrial acquisition systems that sample sensor outputs while retaining 16-bit numerical resolution. Its industrial-temperature specification and 550 mW typical consumption are useful for compact measurement equipment operating from a single +5 V rail. Use the converter behind the analog front end and anti-alias filter, with controlled input settling and a clean clock source. The 2.5 MHz output word rate supports substantial real-time bandwidth, although applications requiring higher throughput must evaluate a faster converter.
Empfohlen
Medical Monitoring Equipment
AD9260AS can be used in medical monitoring and diagnostic instrumentation when its 16-bit resolution and 2.5 MHz output word rate cover the required physiological bandwidth. It is typically positioned after sensor conditioning, instrumentation amplification, and anti-alias filtering so that the ADC receives a settled bipolar or unipolar signal within its input range. The single +5 V supply simplifies analog power distribution, while the power-scaling circuit offers lower consumption at reduced rates. System designers must still implement appropriate patient protection, isolation, validation, and regulatory controls.
Empfohlen
Precision Instrumentation
AD9260AS fits laboratory and process instrumentation requiring accurate conversion of moderately high-bandwidth analog signals. Its 16-bit resolution preserves fine numerical detail, and the 8-times oversampling architecture is intended to provide exceptional dynamic range over a wide bandwidth. The converter should follow low-noise amplification and filtering stages, while its digital outputs connect to a controller or FPGA through timing-conscious routing. Compared with a lower-resolution converter, AD9260AS supports more precise measurements; compared with a much faster ADC, it offers a simpler 2.5 MHz word-rate design point.
Empfohlen
Audio and Waveform Capture
AD9260AS can capture audio and general-purpose waveform signals when the required bandwidth is consistent with its 2.5 MHz output word rate. The 16-bit conversion resolution provides useful dynamic range for waveform analysis, while the wide-band oversampling architecture targets clean acquisition across the supported analog bandwidth. Use a dedicated anti-alias filter, low-noise input stage, and controlled clock routing to prevent out-of-band energy and timing errors from limiting capture quality. This application benefits from the simple +5 V supply, though very high-rate waveform capture requires a faster output interface and converter.
Empfohlen
Embedded Control and Monitoring
AD9260AS can feed an embedded controller in power-monitoring, condition-monitoring, and factory-test systems where 16-bit conversion data is required at a moderate rate. The 2.5 MHz output word rate allows substantial acquisition throughput, and the 44-pin MQFP package provides a manageable surface-mount interface for multilayer boards. Place the converter near the conditioned sensor input, use a low-jitter clock, and account for digital-output loading when connecting the bus to an FPGA or processor. For low-power operation, the scaling circuit can reduce converter consumption toward 150 mW at reduced rates.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für AD9260AS – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | AD9260ASZ | AD9260ASRL |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | MQFP-44 (10 x 10 mm) | MQFP-44 (10 x 10 mm) - same package | MQFP-44 (10 x 10 mm) - same package |
| Resolution | 16 bit | 16 bit | 16 bit |
| Output Word Rate | 2.5 MHz | 2.5 MHz | 2.5 MHz |
| Supply Voltage | +5 V | +5 V | +5 V |
| Oversampling Ratio | 8x | 8x | 8x |
| Process Technology | Advanced CMOS | Advanced CMOS | Advanced CMOS |
Wichtigste Unterscheidungsmerkmale
- Same 44-pin MQFP interface for direct PCB substitution (vs. AD9260ASZ)
- 16-bit resolution at a 2.5 MHz output word rate (vs. AD9260ASRL)
- Single +5 V operation with selectable power scaling (vs. AD9260ASZ)
Designhinweise
Use the manufacturer application circuit and pin-description table as the authority for the 44-pin MQFP layout. Place local supply-decoupling capacitors adjacent to the device, preserve a low-impedance ground connection, and separate the analog input and clock routing from the parallel digital outputs. Because the MQFP footprint is not represented by a dedicated diagram in the available package library, verify every land pattern against the official package drawing before fabrication.
Treat the AD9260 clock and 16-bit output interface as high-speed digital nets. Route clock traces with short paths and continuous references, avoid unnecessary stubs, and account for receiver threshold, trace length, and loading when terminating the outputs. The available product information identifies a 2.5 MHz output word rate but does not state the maximum analog input frequency or digital timing limits; confirm those values in the manufacturer datasheet before setting impedance or timing constraints.
Estimated: at the documented single +5 V supply and typical device consumption of 550 mW, the device-side supply current is approximately 110 mA using I = P/V. This estimate excludes the input current of external support components and board-level conversion losses. Provide local decoupling and a supply path sized for the confirmed operating mode, particularly when the power-scaling circuit is used to approach the documented 150 mW consumption at reduced clock and data rates.
Do not treat AD9260AS, AD9260ASZ, and AD9260ASRL as interchangeable solely because they share the AD9260 family name. Verify the ordering guide for package, temperature grade, component finish, reel or tube format, and traceability requirements. Also avoid selecting the converter before confirming that 2.5 MHz output word rate, analog input range, and input bandwidth satisfy the system signal requirements.
Compliance-Informationen
The available manufacturer product information does not state the requested compliance and finish attributes. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals status for the exact ordering code through the manufacturer product documentation before release.