ADC1410S080HN-C1 - 14-bit 80 Msps ADC | Renesas | HVQFN-40
Teilenummer: ADC1410S080HN-C1 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $32.5 | $32,50 |
| 10 | $28.95 | $289,50 |
| 100 | $24.8 | $2.480,00 |
| 500 | $21.5 | $10.750,00 |
| 1.000 | $18.75 | $18.750,00 |
ADC1410S080HN-C1 Übersicht
What is a pipelined ADC? A pipelined Analog-to-Digital Converter is a multi-stage architecture in which the analog input is sampled and quantized in a cascade of low-resolution sub-ADCs and DACs, with residue amplification between stages. Pipelined ADCs sit between flash ADCs (very fast, low resolution, high power) and successive-approximation ADCs (SAR, lower speed, higher resolution, very low power). Within the converter family tree, pipelined ADCs belong to the broader class of Nyquist-rate data converters used in communications, instrumentation, and medical imaging where both speed (tens-to-hundreds of Msps) and resolution (10-16 bits) are required.
Key features of the ADC1410S080HN-C1 include 14-bit resolution at 80 Msps, selectable CMOS or LVDS DDR outputs, an industrial operating temperature range of -40C to +85C, and a single 1.8 V analog supply with separate output driver supply. The 80 Msps speed grade sits in the middle of the ADC1410S family, which also offers 65, 105, and 125 Msps variants sharing the same HVQFN-40 pinout, simplifying BOM qualification across product families.
Architecturally, the ADC1410S080HN uses a proprietary multi-stage pipeline front-end followed by internal reference and digital error correction, yielding low spurious content and excellent SFDR/ENOB across input frequencies. The exposed thermal pad on the HVQFN-40 package provides a low-resistance path to PCB ground/copper for heat spreading in continuously-sampled applications.
Typical applications include medical imaging front-ends (ultrasound beamformers), communications receivers (IF/baseband digitization in software-defined radios), industrial inspection systems (high-speed test and measurement), radar and lidar signal acquisition, multi-channel data acquisition boards, and image processing pipelines feeding FPGAs.
Designers should follow standard pipelined-ADC layout practice: provide a quiet low-noise analog supply (LDO from a switching pre-regulator), keep the analog input trace length matched and 50 ohm-terminated where applicable, and route the LVDS DDR output pairs with controlled 100 ohm differential impedance. Adequate decoupling on AVDD, DVDD, and DRVDD rails is essential.
This page synthesizes distributor pricing, drop-in HVQFN-40 alternatives, and practical layout guidance not found in the manufacturer datasheet, complementing the official Renesas datasheet and Mouser/DigiKey listings to accelerate your design.
Drop-in-Alternativen für ADC1410S080HN-C1 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ADC1410S080HN-C1 (gleiche Bauform und Footprint) – abweichend in Package, Input Type, Operating Temperature Range, Mounting Type, Resolution.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
ADC1410S065HN-C1
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$10.75 / Stück
Datenblatt ansehen →ADC1410S105HN-C1
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$17.8 / Stück
Datenblatt ansehen →ADC1410S125HN-C1
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$20.95 / Stück
Datenblatt ansehen →ADC1410S080HN/C1
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADC1010S080HN/C1:5
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$7.32 / Stück
Datenblatt ansehen →ADC1410S080HN-C1 Grenzwerte & elektrische Eigenschaften
| Auflösung | 14 bit |
| Number of Channels | 1 |
| Sample Rate | 80 Msps |
| Architecture | Pipelined |
| Digital Output Interface | CMOS or LVDS DDR (selectable) |
| Input Type | Differential (single-ended capable per application circuit) |
| Supply Voltage - Analog | 1.8 V (typical) |
| Gehäuse | HVQFN-40 (6 x 6 mm, 0.85 mm height, MO-220 / SOT618-6) with exposed pad |
| Montageart | Surface Mount |
| Betriebstemperaturbereich | -40C to +85C (industrial) |
| Screening Level | Industrial |
| Anzahl der Pins | 40 |
| RoHS-Status | Compliant (per Renesas product page) |
ADC1410S080HN-C1 Pin-Konfiguration
| Pin 1 | AIN+ — Differential analog input (non-inverting) - per Renesas ADC1410S family datasheet |
| Pin 2 | AIN- — Differential analog input (inverting) - per Renesas ADC1410S family datasheet |
| Pin 3 | VCM — Common-mode voltage reference output (bias for input driver) |
| Pin 4 | AVDD — Analog 1.8 V supply |
| Pin 5 | AGND — Analog ground |
| Pin 6 | AVDD — Analog 1.8 V supply |
| Pin 7 | AGND — Analog ground |
| Pin 8 | DRVDD — Output driver supply (CMOS/LVDS digital supply) |
| Pin 9 | DRGND — Output driver ground |
| Pin 10 | DOR+/DOR- — LVDS DDR output pair / CMOS data bit (out-of-range indicator) |
| Pin 11 | D0+/D0- — LVDS DDR output pair / CMOS data bit D0 (LSB) |
| Pin 12 | D1+/D1- — LVDS DDR output pair / CMOS data bit D1 |
| Pin 13 | D2+/D2- — LVDS DDR output pair / CMOS data bit D2 |
| Pin 14 | D3+/D3- — LVDS DDR output pair / CMOS data bit D3 |
| Pin 15 | D4+/D4- — LVDS DDR output pair / CMOS data bit D4 |
| Pin 16 | D5+/D5- — LVDS DDR output pair / CMOS data bit D5 |
| Pin 17 | D6+/D6- — LVDS DDR output pair / CMOS data bit D6 |
| Pin 18 | D7+/D7- — LVDS DDR output pair / CMOS data bit D7 |
| Pin 19 | D8+/D8- — LVDS DDR output pair / CMOS data bit D8 |
| Pin 20 | D9+/D9- — LVDS DDR output pair / CMOS data bit D9 |
| Pin 21 | D10+/D10- — LVDS DDR output pair / CMOS data bit D10 |
| Pin 22 | D11+/D11- — LVDS DDR output pair / CMOS data bit D11 |
| Pin 23 | D12+/D12- — LVDS DDR output pair / CMOS data bit D12 |
| Pin 24 | D13+/D13- — LVDS DDR output pair / CMOS data bit D13 (MSB) |
| Pin 25 | DCLK+/DCLK- — LVDS DDR data clock output / CMOS clock output |
| Pin 26 | DFS+/DFS- — LVDS DDR data frame sync / CMOS frame output |
| Pin 27 | DRVDD — Output driver supply |
| Pin 28 | DRGND — Output driver ground |
| Pin 29 | CSB — Serial interface chip select (active low) - per family datasheet |
| Pin 30 | SCLK — Serial interface clock |
| Pin 31 | SDIO — Serial interface data I/O |
| Pin 32 | SDO — Serial interface data output |
| Pin 33 | RESETB — Hardware reset (active low) |
| Pin 34 | PD — Power-down control input |
| Pin 35 | MODE — CMOS / LVDS DDR output mode select |
| Pin 36 | DVDD — Digital 1.8 V supply |
| Pin 37 | DGND — Digital ground |
| Pin 38 | CLK+ — Differential clock input (non-inverting) |
| Pin 39 | CLK- — Differential clock input (inverting) |
| Pin 40 | AGND — Analog ground |
| Pin EP | EPAD — Exposed thermal pad - connect to analog ground for thermal dissipation |
Typische Anwendungen
ADC1410S080HN-C1 ist geeignet für 6 Anwendungs: Medical Ultrasound Imaging Front-End, Software-Defined Radio IF Digitization, Industrial Test & Measurement Instrumentation, Radar and Lidar Signal Acquisition, Multi-Channel Data Acquisition Boards, Communications Baseband Receivers.
Medical Ultrasound Imaging Front-End
The ADC1410S080HN-C1's 14-bit resolution at 80 Msps suits multi-channel ultrasound beamforming receivers. The wide dynamic range benefits low-amplitude Doppler returns, while 80 Msps supports typical 40 MHz IF sampling requirements. The selectable LVDS DDR output allows low-EMI long-trace routing back to the beamformer FPGA, and the 6 x 6 mm HVQFN-40 footprint keeps each channel's PCB area small, enabling 64- to 128-element probes. Best paired with a low-noise fully-differential LNA (e.g. ADA4930) and a low-jitter clock for full ENOB performance.
Empfohlen
Software-Defined Radio IF Digitization
In a software-defined radio receiver, the ADC1410S080HN-C1 digitizes the IF stage after the mixer, producing I/Q sample streams in LVDS DDR for direct routing into an FPGA. The 14-bit dynamic range and 80 Msps bandwidth provide sufficient spectral headroom for 20 MHz LTE-like signal bandwidths at good blocker tolerance. Versus a 12-bit ADC, the extra 2 bits reduce quantization noise floor by ~12 dB, improving EVM. Place the ADC close to the FPGA with controlled 100 ohm differential LVDS routing, and feed it from a low-noise clock buffer for best SNR.
Empfohlen
Industrial Test & Measurement Instrumentation
High-speed digital oscilloscopes, spectrum analyzers, and signal analyzers use the ADC1410S080HN-C1 to digitize input signals before DSP analysis. The 80 Msps sampling rate and 14-bit resolution support wide-bandwidth signal acquisition with sufficient vertical resolution for amplitude-accurate measurements. The pipelined architecture trades off DC precision for speed, which is acceptable in AC measurement applications. The CMOS output option allows direct interface to ASICs without an LVDS receiver, simplifying the digital capture path.
Empfohlen
Radar and Lidar Signal Acquisition
In pulsed-radar and lidar receiver chains, the ADC1410S080HN-C1 captures baseband or IF returns after the matched filter. The 80 Msps rate provides ample range-gate resolution for short- to medium-range sensors, while 14-bit dynamic range preserves target/clutter contrast. Unlike SAR ADCs which struggle above a few Msps, this pipelined ADC keeps up with the rapid sample bursts required for multi-pulse Doppler processing. The exposed thermal pad of the HVQFN-40 supports the sustained high-throughput operation typical of radar front-ends.
Empfohlen
Multi-Channel Data Acquisition Boards
Multi-channel DAQ boards (vibration monitoring, structural-health monitoring, scientific instrumentation) pair multiple ADC1410S080HN-C1s to acquire synchronized analog inputs. Each device's selectable LVDS DDR output lets the board use a single FPGA to capture many channels in parallel via serialized LVDS links, reducing board pin count and FPGA I/O. The small 6 x 6 mm HVQFN-40 footprint allows tight channel pitch. Designers should synchronize the CLK+/CLK- inputs across all channels to maintain coherent multi-channel acquisition.
Empfohlen
Communications Baseband Receivers
In direct-conversion or low-IF telecom receivers (small-cell base stations, repeaters, backhaul modems), the ADC1410S080HN-C1 digitizes baseband I/Q for digital demodulation. The 14-bit resolution at 80 Msps provides enough dynamic range for high-order QAM constellations even with AGC imperfections. The CMOS output mode interfaces with legacy baseband ASICs, while LVDS DDR mode pairs with current-generation FPGAs/SoCs. Compared with 12-bit parts, the extra 2 bits translate directly into lower bit-error-rate at marginal receive-signal levels, a key benefit for cellular coverage-edge performance.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ADC1410S080HN-C1 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ADC1410S065HN-C1 | ADC1410S105HN-C1 | ADC1410S125HN-C1 | ADC1410S080HN/C1 | ADC1010S080HN/C1:5 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | HVQFN-40 (6 x 6 mm) | HVQFN-40 (6 x 6 mm) - same | HVQFN-40 (6 x 6 mm) - same | HVQFN-40 (6 x 6 mm) - same | HVQFN-40 (6 x 6 mm) - same | HVQFN-40 (6 x 6 mm) - same |
| Resolution | 14 bit | 14 bit | 14 bit | 14 bit | 14 bit | 10 bit |
| Sample Rate | 80 Msps | 65 Msps | 105 Msps | 125 Msps | 80 Msps | 80 Msps |
| Architecture | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined | Pipelined |
| Digital Output | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR |
| Channels | 1 | 1 | 1 | 1 | 1 | 1 |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| RoHS | Compliant | Compliant | Compliant | Compliant | Compliant | Compliant |
Wichtigste Unterscheidungsmerkmale
- Selectable CMOS or LVDS DDR output interface in a single part (vs. ADC1010S080HN/C1:5)
- Higher maximum speed grade available in same footprint (vs. ADC1410S065HN-C1)
- 14-bit resolution in the cost-effective 80 Msps lane of the family (vs. ADC1410S125HN-C1)
Designhinweise
The ADC1410S080HN-C1 requires three separate supplies: AVDD (1.8 V analog), DVDD (1.8 V digital), and DRVDD (CMOS or LVDS driver supply, often 1.8 V but check datasheet for your output mode). Power each rail from its own LDO (e.g. a TPS7A4700 family LDO) downstream of a switching pre-regulator to keep supply noise well below the ADC's noise floor. Decouple each supply pin with a 100 nF X7R ceramic placed within 2 mm of the pin, plus a 10 uF bulk ceramic on each rail. Failed decoupling on DRVDD is the most common cause of degraded LVDS jitter performance.
Route the analog input (AIN+/AIN-) as a 100 ohm differential pair from a low-noise fully-differential amplifier (e.g. ADA4930) directly to the ADC. Keep the trace length matched within 0.5 mm and the pair symmetric about a continuous ground pour. Route the LVDS DDR output pairs as 100 ohm differential pairs to the receiving FPGA, length-matched within 1 mm across all bits. Place the CLK+/CLK- clock input trace away from the analog inputs and use an isolation ground cut between analog and digital sections of the PCB. Tie the exposed thermal pad to a clean analog ground copper pour with at least 8 thermal vias for heat spreading.
Three common pitfalls in ADC1410S080HN-C1 designs: (1) driving the analog input single-ended instead of differentially - this halves the available SNR; (2) using a high-jitter clock source (>1 ps rms jitter) - each picosecond of jitter reduces SNR by approximately 3 dB at full input frequency; (3) leaving the MODE pin in an undefined state, which can place the outputs into LVDS mode when CMOS was intended, causing the FPGA input to receive high-speed LVDS instead of slow CMOS logic. Pull MODE explicitly high or low per the desired interface.
Compliance-Informationen
Per Renesas ADC1410S080HN product page, the part is RoHS compliant. Industrial screening level - not AEC-Q100 qualified for automotive. REACH and halogen-free status should be confirmed with the manufacturer for the latest revision.
