ADC1410S065HN-C1 - 14-bit 65 MSPS Single-Channel ADC | Renesas
Teilenummer: ADC1410S065HN-C1 ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.2 | $162,00 |
| 100 | $13.85 | $1.385,00 |
| 500 | $12.1 | $6.050,00 |
| 1.000 | $10.75 | $10.750,00 |
ADC1410S065HN-C1 Übersicht
An Analog-to-Digital Converter (ADC) is a data-acquisition component that converts real-world analog voltage or current signals into discrete digital codes for processing by microcontrollers, DSPs, FPGAs, or SoCs. Pipelined ADCs are the dominant architecture for sample rates between 1 MSPS and 250 MSPS because they balance high throughput against modest silicon area and reasonable power consumption. The ADC1410S series sits in the hierarchy: ADC -> data converter -> data acquisition IC -> signal chain -> mixed-signal semiconductor. This pipelined architecture makes the part suited to communications, instrumentation, and imaging front-ends.
Key features of the ADC1410S065HN-C1 include selectable CMOS or LVDS DDR digital interface, an SPI control port for mode configuration, an input bandwidth typically suitable for IF-sampling applications, and a single 3.0 V or 5 V analog supply domain. The pipelined core is preceded by a sample-and-hold front-end and followed by on-chip digital error correction. The HVQFN-40 package exposes a thermal pad that must be soldered to a sufficient copper pour for specified performance.
From a system-design perspective, the device includes an internal bandgap reference and supports both internal and external reference operation through pin strapping. The LVDS DDR option enables double-data-rate clocking so that one LVDS pair transmits two samples per clock edge, easing board routing at 65 MSPS. A power-down (PD) pin and a flexible clock duty-cycle stabilizer are integrated. Typical dynamic performance figures reported in the manufacturer datasheet include ENOB and SFDR figures appropriate for communications receivers.
Typical applications include software-defined radio (SDR) and IF-sampling receivers, medical imaging front-ends such as ultrasound beamformers, industrial process control data acquisition, baseband digitization in wireless infrastructure, and high-speed instrumentation. The 65 MSPS ceiling gives headroom for moderate-bandwidth signals while keeping power well below 100 mW. The LVDS DDR mode is preferred in multi-channel systems where skew must be tightly controlled.
When laying out the PCB, treat the analog and digital grounds as a single low-impedance plane with careful partition around the ADC1410S065HN-C1, and bypass each supply pin with 100 nF and 10 uF capacitors placed within 2-3 mm of the package. A symmetric differential analog input trace is required to preserve SFDR. This page synthesizes distributor pricing, parametric comparison, drop-in alternatives, and PCB design notes not collected in a single place on the manufacturer product page.
Drop-in-Alternativen für ADC1410S065HN-C1 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ADC1410S065HN-C1 (gleiche Bauform und Footprint) – abweichend in Package, Input Type, Resolution, Operating Temperature Range, Data Interface.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
ADC1410S080HN-C1
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$18.75 / Stück
Datenblatt ansehen →ADC1410S105HN-C1
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$17.8 / Stück
Datenblatt ansehen →ADC1410S125HN-C1
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$20.95 / Stück
Datenblatt ansehen →ADC1210S065HN/C1
✅ Drop-In✓ Auf Lager
$8.4 / Stück
Datenblatt ansehen →ADC1213S125HN-C1
✅ Drop-In✓ Auf Lager
$18.45 / Stück
Datenblatt ansehen →ADC1112D125HN-C18
✅ Drop-In✓ Auf Lager
$9.48 / Stück
Datenblatt ansehen →ADC1410S065HN-C1 Grenzwerte & elektrische Eigenschaften
| Auflösung | 14 bit |
| Sample Rate | 65 MSPS (65 Msps nominal) |
| Number of Channels | 1 |
| Architecture | Pipelined |
| Gehäuse | HVQFN-40 (SOT618-6), 6 x 6 mm, 0.85 mm height |
| Package Code (JEDEC) | MO-220, SOT618-6 |
| Montageart | Surface Mount |
| Digital Output Interface | CMOS or LVDS DDR (selectable) |
| Data Interface / Control | Serial, SPI |
| Betriebstemperaturbereich | -40 C to +85 C |
| Screening Level | Industrial |
| Power Supply | 3.0 V / 5 V analog supply |
| Reference | Internal bandgap or external reference (selectable) |
| RoHS-Status | Compliant |
ADC1410S065HN-C1 Pin-Konfiguration
| Pin 1 | VINA — Analog supply voltage |
| Pin 2 | IN+ — Differential analog input positive |
| Pin 3 | IN- — Differential analog input negative |
| Pin 4 | CM — Common-mode voltage output |
| Pin 5 | REFIO — Reference voltage I/O |
| Pin 6 | REFSEL — Internal/external reference select |
| Pin 7 | GND — Analog ground |
| Pin 8 | VIND — Digital supply voltage |
| Pin 9 | GND — Digital ground |
| Pin 10 | CLK+ — Differential clock input positive |
| Pin 11 | CLK- — Differential clock input negative |
| Pin 12 | PD — Power-down control input |
| Pin 13 | OUTMODE — Output mode select (CMOS/LVDS) |
| Pin 14 | CS — SPI chip-select (active low) |
| Pin 15 | SCLK — SPI serial clock |
| Pin 16 | SDIO — SPI serial data I/O |
| Pin 17 | D0_DDR — Data output bit 0 / DDR pair |
| Pin 18 | D1 — Data output bit 1 |
| Pin 19 | D2 — Data output bit 2 |
| Pin 20 | D3 — Data output bit 3 |
| Pin 21 | D4 — Data output bit 4 |
| Pin 22 | D5 — Data output bit 5 |
| Pin 23 | D6 — Data output bit 6 |
| Pin 24 | D7 — Data output bit 7 |
| Pin 25 | D8 — Data output bit 8 |
| Pin 26 | D9 — Data output bit 9 |
| Pin 27 | D10 — Data output bit 10 |
| Pin 28 | D11 — Data output bit 11 |
| Pin 29 | D12 — Data output bit 12 |
| Pin 30 | D13 — Data output bit 13 (MSB) |
| Pin 31 | DRDY — Data ready / clock output |
| Pin 32 | NC — Not connected |
| Pin 33 | GND — Digital ground |
| Pin 34 | DCLK+ — DDR clock output positive |
| Pin 35 | DCLK- — DDR clock output negative |
| Pin 36 | FS — Frame sync output |
| Pin 37 | OGND — Output driver ground |
| Pin 38 | OVDD — Output driver supply |
| Pin 39 | NC — Not connected |
| Pin 40 | NC — Not connected |
Typische Anwendungen
ADC1410S065HN-C1 ist geeignet für 6 Anwendungs: Software-Defined Radio IF Sampling, Medical Ultrasound Beamformer, Industrial Process Data Acquisition, Wireless Baseband Digitization, High-Speed Test and Measurement Instrumentation, Automotive Radar Signal Digitization.
Software-Defined Radio IF Sampling
The ADC1410S065HN-C1 fits software-defined radio IF-sampling receivers because its 65 MSPS rate and 14-bit ENOB can digitize IF bands up to roughly 200 MHz with strong SFDR. The pipelined core preserves the small-signal dynamic range required by QAM and OFDM demodulation algorithms. LVDS DDR output eases routing into an FPGA baseband processor with deterministic clock-to-data skew. Place a wideband differential driver such as an LMH6503 in front of the analog inputs to maintain spurious performance across temperature.
Empfohlen
Medical Ultrasound Beamformer
In medical ultrasound, the ADC1410S065HN-C1 digitizes pre-beamformed RF channels at 65 MSPS with 14-bit resolution, delivering the dynamic range needed for harmonic imaging and Doppler modes. The LVDS DDR output reduces board traces per channel, easing dense probe-front-end layouts. Low power keeps channel-IC thermal budgets manageable in multi-element probes. Combined with a low-noise LNA and time-gain amplifier, the ADC1410S065HN-C1 provides the noise floor and SFDR required for diagnostic ultrasound front-ends.
Empfohlen
Industrial Process Data Acquisition
Factory automation systems use the ADC1410S065HN-C1 to digitize high-speed sensor outputs from vibration, position, and weight-measurement transducers. The 65 MSPS rate oversamples mechanical signals well above the Nyquist minimum, improving SNR through averaging. Industrial -40 C to +85 C screening supports deployment near motor drives and harsh environments. CMOS output mode simplifies direct connection to industrial microcontrollers without an FPGA. The pipelined architecture guarantees monotonic codes required by closed-loop control systems.
Empfohlen
Wireless Baseband Digitization
Wireless infrastructure receivers digitize baseband or low-IF signals with the ADC1410S065HN-C1 to leverage its 14-bit dynamic range and low spurious content. The 65 MSPS ceiling comfortably handles 20 MHz LTE and similar waveforms with margin for digital filtering. LVDS DDR output drives baseband ASICs over short board traces with minimum skew. The internal bandgap reference reduces external component count in space-constrained remote-radio-head designs. Selectable CMOS mode also enables low-cost FPGA-based test platforms.
Empfohlen
High-Speed Test and Measurement Instrumentation
Bench-top instruments such as oscilloscope front-ends, spectrum analyzer IF digitizers, and arbitrary waveform generator feedback loops use the ADC1410S065HN-C1 for its 14-bit resolution and selectable LVDS DDR interface. At 65 MSPS the part delivers adequate time resolution for signals up to 25 MHz bandwidth. SPI-controlled gain and offset trim let designers calibrate each channel against an internal reference. The HVQFN-40 footprint supports dense 4- or 8-channel digitizer cards for modular instruments.
Empfohlen
Automotive Radar Signal Digitization
Although the industrial -C1 screening level is not AEC-Q100 qualified, the ADC1410S065HN-C1 can serve development platforms for 24 GHz and 77 GHz automotive radar digitizing baseband or low-IF outputs. The 14-bit resolution preserves target discrimination in dense clutter, and the LVDS DDR output supports high-channel-count antenna arrays. Designers should evaluate the AEC-Q100 grade of the same family for production deployment. For radar prototypes, the pin-compatible ADC1410S125HN-C1 offers higher sample rate when wider instantaneous bandwidth is needed.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ADC1410S065HN-C1 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ADC1410S080HN-C1 | ADC1410S105HN-C1 | ADC1410S125HN-C1 | ADC1210S065HN/C1 | ADC1213S125HN-C1 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | HVQFN-40 (6x6 mm) | HVQFN-40 (6x6 mm) - same | HVQFN-40 (6x6 mm) - same | HVQFN-40 (6x6 mm) - same | HVQFN-40 (6x6 mm) - same | HVQFN-40 (6x6 mm) - same |
| Resolution | 14 bit | 14 bit | 14 bit | 14 bit | 12 bit | 12 bit |
| Sample Rate | 65 MSPS | 80 MSPS | 105 MSPS | 125 MSPS | 65 MSPS | 125 MSPS |
| Channels | 1 | 1 | 1 | 1 | 1 | 1 |
| Digital Output | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR | CMOS or LVDS DDR |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Control Interface | Serial SPI | Serial SPI | Serial SPI | Serial SPI | Serial SPI | Serial SPI |
Wichtigste Unterscheidungsmerkmale
- Selectable CMOS or LVDS DDR output interface (vs. ADC1210S065HN/C1)
- 14-bit resolution at 65 MSPS in HVQFN-40 (vs. ADC1210S065HN/C1)
- Pin-compatible speed upgrade path to 125 MSPS (vs. ADC1410S080HN-C1)
Designhinweise
Place 100 nF X7R ceramic bypass capacitors within 2-3 mm of every VINA, VIND, and OVDD pin, and add a single 10 uF tantalum or polymer bulk capacitor at the package entry. Split the analog and digital grounds only under the ADC footprint and stitch them together at a single point near the exposed thermal pad. Keep the differential analog input trace pair symmetric and length-matched within 0.5 mm to preserve SFDR.
Drive CLK+ and CLK- with a low-jitter differential clock source such as a dedicated clock generator or a clean FPGA LVDS output. Jitter on the sample clock directly degrades SNR, with the rule-of-thumb SNR_dB loss equal to 20*log10(2*pi*Fin* tjitter). At a 70 MHz IF input and 65 MSPS, target clock jitter below 500 fs RMS. Terminate the LVDS DDR outputs with 100 ohm differential near the FPGA receiver to avoid reflections.
The HVQFN-40 exposed thermal pad must be soldered to a continuous ground copper pour of at least 1 square inch (6 cm^2) on the top layer, with thermal vias to inner ground planes. Without this, junction temperature can exceed the 125 C limit at full sample rate and 5 V analog supply. Estimated: at 5 V analog and 65 MSPS CMOS output the device dissipates approximately 250 mW; with theta_JA around 35 C/W on a 4-layer JEDEC board, junction rises only 9 C above ambient.
Do not leave the REFSEL pin floating - tie it high for internal reference or low for external reference per the datasheet. Always issue a software SPI reset (or toggle PD) after power-up to guarantee a known mode. The OUTMODE pin must be set BEFORE CS is asserted or output contention may occur. Avoid driving the analog input before the PD pin is deasserted, otherwise the input ESD structure can back-feed current into the upstream driver.
Compliance-Informationen
RoHS and REACH compliant per Renesas product page. Industrial screening level -40 C to +85 C; not AEC-Q100 qualified - reference AEC-Q100 grade of the same family for automotive designs.
