AT90CAN128-16AJ 16MHz 128KB CAN AVR MCU | Microchip
Teilenummer: AT90CAN128-16AJ ✓ AktivAT90CAN128-16AJ Übersicht
An 8-bit microcontroller is a programmable semiconductor that combines a processor core, program memory, data memory, and peripheral interfaces on one integrated circuit. The AT90CAN128 belongs to the Microchip AVR 90CAN family, combining the AVR enhanced RISC core with dedicated CAN communications hardware. Its architecture supports single-clock-cycle instruction execution and is intended for embedded control systems that require deterministic peripheral handling and networked data exchange.
Three headline resources define this device: 128 KB of flash for application code, 4 KB each of SRAM and EEPROM, and a maximum stated clock speed of 16 MHz. The 53 general-purpose I/O lines support digital inputs, outputs, and interrupt-driven interfaces. Its integrated peripherals also include 32 general-purpose working registers, a real-time counter, four timer/counter blocks with compare and PWM modes, two USARTs, and a byte-oriented two-wire serial interface.
The integrated CAN controller is the primary technical feature for industrial networking. CAN 2.0A/V2.0B compatibility allows the MCU to participate in standardized controller-area-network communication systems while retaining the simplicity of an 8-bit architecture. The ISP flash memory supports in-system programming, and the combination of timers, serial interfaces, and CAN makes it possible to consolidate communications, timing, and control functions into one device.
Typical applications include CAN-connected industrial controllers, automotive electronics modules, building-automation nodes, sensor hubs, motor-control equipment, and CAN-compatible instrumentation. In these systems, the MCU can process local input signals, operate timers or PWM outputs, exchange diagnostic information over CAN, and provide serial service or configuration interfaces without requiring a separate communications controller.
PCB design should preserve the 64-TQFP footprint and route the CAN RX and TX pins to the transceiver interface rather than directly to a bus. Decoupling, programming access, reset behavior, clock stability, and exposed ground-return paths require close attention to the manufacturer's pin and layout guidance. When the clock or memory requirements differ, AT90CAN128 family options can provide a simpler replacement path, although firmware and timing should be revalidated.
This page combines the manufacturer device specifications with package, programming, replacement, application, and design guidance. It also identifies the distinctions that matter when comparing speed grades, temperature grades, memory capacities, and package-compatible family members for an embedded CAN design.
Drop-in-Alternativen für AT90CAN128-16AJ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit AT90CAN128-16AJ (gleiche Bauform und Footprint) – abweichend in Package, CAN Controller, General-Purpose I/O Lines, General-Purpose Working Registers, Flash Memory.
AT90CAN128-16AU
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →AT90CAN128-15AZ
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →AT90CAN128-15AJ
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
AT90CAN128-16AZ
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
AT90CAN64-16AJ
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
AT90CAN128-16AJ Grenzwerte & elektrische Eigenschaften
| Product Type | 8-bit AVR RISC microcontroller with CAN controller |
| Maximale Taktfrequenz | 16 MHz |
| Flash Memory | 128 KB |
| EEPROM | 4 KB |
| SRAM | 4 KB |
| General-Purpose I/O Lines | 53 lines |
| General-Purpose Working Registers | 32 registers |
| CAN Controller Compliance | CAN V2.0A and V2.0B |
| Architecture | AVR enhanced RISC |
| Program Memory Type | ISP flash |
| Timer/Counters | 4 timers with compare modes and PWM |
| UART Count | 2 USARTs |
| Serial Interface | Byte-oriented two-wire serial interface |
| Gehäuse | 64-pin TQFP, 14 mm x 14 mm |
| Montageart | Surface mount |
AT90CAN128-16AJ 64-pin tqfp, 14 mm x 14 mm Pinbelegungsleitfaden
Pinbelegung für AT90CAN128-16AJ (64-pin tqfp, 14 mm x 14 mm-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für AT90CAN128-16AJ.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
AT90CAN128-16AJ ist geeignet für 6 Anwendungs: CAN-Based Industrial Control Node, Automotive CAN Interface Module, Building Automation Sensor Hub, Motor Control and PWM System, CAN-Compatible Test and Measurement Instrument, Programmable CAN Gateway.
CAN-Based Industrial Control Node
The AT90CAN128-16AJ fits an industrial control node that must combine network communication with deterministic local control. Its 16 MHz AVR core provides processing capacity for state-machine logic, while the integrated CAN V2.0A/V2.0B controller handles bus communication without requiring a separate CAN controller. The 53 general-purpose I/O lines can support discrete inputs, outputs, status indicators, and actuator interfaces, while four timer/counter blocks handle timing or PWM tasks. Two USARTs add service and diagnostic channels. Firmware must be checked for execution-time margin, and the CAN transceiver, termination, isolation, and protection network should be designed separately around the MCU pins.
Empfohlen
Automotive CAN Interface Module
The AT90CAN128-16AJ is suitable for an automotive interface module that translates vehicle-network signals into a local control or diagnostic interface. Its CAN controller, 53 I/O lines, two USARTs, and four timers allow the module to handle communication, sensors, and discrete outputs in a compact 64-pin TQFP. The 16 MHz clock supports responsive protocol processing, while 128 KB of flash provides room for layered CAN stacks and application code. The exact ordering code must be checked against the vehicle's environmental requirements, and the PCB should include a protected transceiver interface rather than connecting MCU CAN pins directly to a physical bus.
Empfohlen
Building Automation Sensor Hub
The AT90CAN128-16AJ can serve as a building-automation hub for collecting sensor data and distributing control commands over a CAN network. Its 4 KB SRAM supports message buffering and protocol state, while the 128 KB ISP flash accommodates application firmware and configuration logic. General-purpose I/O can monitor occupancy, temperature, door, or equipment-status inputs, and the timer/counter resources can support periodic sampling and output timing. A real-time counter is useful for event timestamping, while the two-wire serial interface can simplify configuration during installation. Firmware should account for the processing difference between the 16 MHz target and any 15 MHz replacement before timing-sensitive control is qualified.
Empfohlen
Motor Control and PWM System
The AT90CAN128-16AJ is appropriate for a CAN-commanded motor or actuator controller where local timing must remain responsive. Four timer/counter blocks with compare modes and PWM support generate deterministic control signals, while the CAN controller receives motion commands and reports operating status. At 16 MHz, the AVR core can execute control loops, fault handling, and communication tasks, subject to the chosen PWM frequency and computation load. The 53 I/O lines provide flexibility for gate-control signals, position inputs, and fault flags. Validate timer prescaler calculations, interrupt latency, and update rates for the target firmware, especially if the design is considered for a 15 MHz family alternative.
Empfohlen
CAN-Compatible Test and Measurement Instrument
The AT90CAN128-16AJ can support a compact test or measurement instrument that combines stimulus control with CAN-based reporting. Its 128 KB flash, 4 KB EEPROM, and 4 KB SRAM allow local configuration storage, acquisition buffering, and firmware updates, while the two USARTs provide independent communication paths for a host and peripheral equipment. Four timers support trigger, delay, and sampling functions, and the real-time counter can improve event timing. The CAN interface is useful for integrating the instrument with automated test systems. Engineers should budget interrupt and serial bandwidth, preserve deterministic timing under maximum peripheral activity, and validate analog measurement accuracy separately from the digital control subsystem.
Empfohlen
Programmable CAN Gateway
The AT90CAN128-16AJ is well suited to a programmable gateway that receives CAN messages, applies routing or transformation rules, and exposes status through serial links. Its 16 MHz AVR processor, 53 I/O lines, two USARTs, and byte-oriented two-wire interface allow the gateway to bridge CAN with service ports or local configuration networks. The 128 KB program memory is useful for protocol tables and routing logic, while EEPROM can retain configuration settings when the application requires it. Message latency should be measured with realistic bus loading, and the design should include watchdog recovery, bus-error handling, and a controlled update path through the ISP interface.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für AT90CAN128-16AJ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | AT90CAN128-16AU | AT90CAN128-15AZ | AT90CAN128-15AJ | AT90CAN128-16AZ | AT90CAN64-16AJ |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP, 14 mm x 14 mm | 64-pin TQFP, 14 mm x 14 mm | 64-pin TQFP, 14 mm x 14 mm | 64-pin TQFP, 14 mm x 14 mm | 64-pin TQFP, 14 mm x 14 mm | 64-pin TQFP, 14 mm x 14 mm |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 15 MHz | 15 MHz | 16 MHz | 16 MHz |
| Flash Memory | 128 KB | 128 KB | 128 KB | 128 KB | 128 KB | 64 KB |
| CAN Controller | CAN V2.0A and V2.0B compatible | CAN V2.0A and V2.0B compatible | CAN V2.0A and V2.0B compatible | CAN V2.0A and V2.0B compatible | CAN V2.0A and V2.0B compatible | CAN V2.0A and V2.0B compatible |
| General-Purpose I/O Lines | 53 lines | 53 lines | 53 lines | 53 lines | 53 lines | 53 lines |
Wichtigste Unterscheidungsmerkmale
- Higher clock speed within the same package (vs. AT90CAN128-15AZ)
- Full 128 KB program-memory capacity (vs. AT90CAN64-16AJ)
- Single-device CAN and serial integration (vs. ATMEGA128-16AU)
Designhinweise
Route the CAN RX and TX signals from the AT90CAN128-16AJ to the pins of a suitable CAN transceiver; the MCU pins are logic-level interface signals and must not connect directly to the physical CAN bus. Place the transceiver close enough to the connector or bus interface to minimize exposed high-speed differential routing. Keep transceiver supply filtering and protection close to their associated pins, and observe the manufacturer's recommended grounding and isolation arrangement.
Use the 64-pin TQFP pin table and footprint drawing as the authoritative source for every connection. Place decoupling capacitors at the supply pins with very short return paths to the ground plane, and keep clock and reset traces away from CAN RX/TX and other switching nodes. The package has fine-pitch leads, so verify pad dimensions, solder mask clearance, paste stencil apertures, and the board's assembly orientation against the manufacturer drawing before releasing production files.
Do not treat AT90CAN128-16AU, AT90CAN128-15AZ, or another AT90CAN member as an unconditional substitute. Although the candidates use the same 64-pin TQFP arrangement, clock speed, ordering-code qualification, memory capacity, and family-specific behavior can affect production suitability. Re-run timing analysis when changing from 16 MHz to 15 MHz, check code size when moving to the 64 KB AT90CAN64 option, and verify all pin functions against the exact replacement datasheet.
The AT90CAN128-16AJ combines a 16 MHz core, CAN controller, timers, and serial peripherals, so supply design must account for both active processing and peripheral current. Follow the manufacturer datasheet for recommended capacitors, clock components, reset behavior, and supply sequencing. Confirm that the regulator has adequate transient response for digital switching while avoiding excessive routing impedance between the supply source and the device.
Compliance-Informationen
The manufacturer product page and ordering documentation should be checked for the definitive RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status of AT90CAN128-16AJ.