Microchip Technology

AT90CAN128-16AJ 16MHz 128KB CAN AVR MCU | Microchip

MPN: AT90CAN128-16AJ ✓ Aktif
64-pin TQFP, 14 mm x 14 mm Package 16 MHz Speed 128 KB Memory
MOQ: 1 |

AT90CAN128-16AJ Ringkasan

The Microchip Technology AT90CAN128-16AJ is a low-power 8-bit AVR RISC microcontroller with a 16 MHz clock, 128 KB of ISP flash memory, 4 KB of EEPROM, 4 KB of SRAM, and 53 general-purpose I/O lines. It integrates a CAN 2.0A/V2.0B-compatible controller and is packaged in a 64-pin TQFP measuring 14 mm by 14 mm.

An 8-bit microcontroller is a programmable semiconductor that combines a processor core, program memory, data memory, and peripheral interfaces on one integrated circuit. The AT90CAN128 belongs to the Microchip AVR 90CAN family, combining the AVR enhanced RISC core with dedicated CAN communications hardware. Its architecture supports single-clock-cycle instruction execution and is intended for embedded control systems that require deterministic peripheral handling and networked data exchange.

Three headline resources define this device: 128 KB of flash for application code, 4 KB each of SRAM and EEPROM, and a maximum stated clock speed of 16 MHz. The 53 general-purpose I/O lines support digital inputs, outputs, and interrupt-driven interfaces. Its integrated peripherals also include 32 general-purpose working registers, a real-time counter, four timer/counter blocks with compare and PWM modes, two USARTs, and a byte-oriented two-wire serial interface.

The integrated CAN controller is the primary technical feature for industrial networking. CAN 2.0A/V2.0B compatibility allows the MCU to participate in standardized controller-area-network communication systems while retaining the simplicity of an 8-bit architecture. The ISP flash memory supports in-system programming, and the combination of timers, serial interfaces, and CAN makes it possible to consolidate communications, timing, and control functions into one device.

Typical applications include CAN-connected industrial controllers, automotive electronics modules, building-automation nodes, sensor hubs, motor-control equipment, and CAN-compatible instrumentation. In these systems, the MCU can process local input signals, operate timers or PWM outputs, exchange diagnostic information over CAN, and provide serial service or configuration interfaces without requiring a separate communications controller.

PCB design should preserve the 64-TQFP footprint and route the CAN RX and TX pins to the transceiver interface rather than directly to a bus. Decoupling, programming access, reset behavior, clock stability, and exposed ground-return paths require close attention to the manufacturer's pin and layout guidance. When the clock or memory requirements differ, AT90CAN128 family options can provide a simpler replacement path, although firmware and timing should be revalidated.

This page combines the manufacturer device specifications with package, programming, replacement, application, and design guidance. It also identifies the distinctions that matter when comparing speed grades, temperature grades, memory capacities, and package-compatible family members for an embedded CAN design.

Alternatif penggantian untuk AT90CAN128-16AJ — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian AT90CAN128-16AJ (sama faktor bentuk dan footprint) — berbeda di dalam Package, CAN Controller, General-Purpose I/O Lines, General-Purpose Working Registers, Flash Memory.

Microchip Technology
Package: 64-pin TQFP
CAN Controller: CAN V2.0A and V2.0B compliant
Bandingkan dengan AT90CAN128-16AJ →
Microchip Technology
Package: 64-TQFP, 14 mm x 14 mm
CAN Controller: CAN V2.0A and CAN V2.0B compliant
General-Purpose I/O Lines: 53
Bandingkan dengan AT90CAN128-16AJ →
Microchip Technology
CAN Controller: CAN 2.0A and CAN 2.0B compliant
Flash Memory: 128 KB (128K x 8)
Bandingkan dengan AT90CAN128-16AJ →

AT90CAN128-16AU

✅ Drop-In
Microchip Technology
📦 64-pin TQFP, 14 mm x 14 mm
8-bit AVR RISC microcontroller with CAN controller · 16 MHz · 128 KB (128K x 8) · 4 KB · 4 KB · 53 lines · 32 registers · CAN 2.0A and CAN 2.0B compliant

Kontak untuk harga

Lihat Datasheet →

AT90CAN128-15AZ

✅ Drop-In
Microchip Technology
📦 64-pin TQFP, 14 mm x 14 mm
8-bit AVR RISC microcontroller · 16 MHz · 128 KB · 4 KB · 4 KB · 53 lines · 32 registers · CAN V2.0A and V2.0B compliant

Kontak untuk harga

Lihat Datasheet →

AT90CAN128-15AJ

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 64-pin TQFP, 14 mm x 14 mm
Clock speed is 15 MHz instead of 16 MHz, a 6.7% reduction; temperature ordering code differs

📋 Alternatif referensi (tidak dalam katalog)

AT90CAN128-16AZ

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 64-pin TQFP, 14 mm x 14 mm
Same 16 MHz speed and 128 KB flash; ordering-code qualification differs

📋 Alternatif referensi (tidak dalam katalog)

AT90CAN64-16AJ

✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 64-pin TQFP, 14 mm x 14 mm
Program memory is reduced from 128 KB to 64 KB, a 50% reduction; clock speed remains 16 MHz

📋 Alternatif referensi (tidak dalam katalog)

AT90CAN128-16AJ Rating Maksimal & Karakteristik Listrik

Product Type 8-bit AVR RISC microcontroller with CAN controller
Frekuensi Bawah Maximum 16 MHz
Flash Memory 128 KB
EEPROM 4 KB
SRAM 4 KB
General-Purpose I/O Lines 53 lines
General-Purpose Working Registers 32 registers
CAN Controller Compliance CAN V2.0A and V2.0B
Architecture AVR enhanced RISC
Program Memory Type ISP flash
Timer/Counters 4 timers with compare modes and PWM
UART Count 2 USARTs
Serial Interface Byte-oriented two-wire serial interface
Paket 64-pin TQFP, 14 mm x 14 mm
Tipe Mounting Surface mount

AT90CAN128-16AJ 64-pin tqfp, 14 mm x 14 mm Diamant Konfigurasi Panduan

Konfigurasi pin untuk AT90CAN128-16AJ (64-pin tqfp, 14 mm x 14 mm pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.

Diamant diagram pakai pakai 64-pin tqfp, 14 mm x 14 mm untuk AT90CAN128-16AJ

Tidak ada data diatribut pin yang tersedia untuk AT90CAN128-16AJ.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

AT90CAN128-16AJ cocok untuk 6 aplikasis: CAN-Based Industrial Control Node, Automotive CAN Interface Module, Building Automation Sensor Hub, Motor Control and PWM System, CAN-Compatible Test and Measurement Instrument, Programmable CAN Gateway.

🏭

CAN-Based Industrial Control Node

The AT90CAN128-16AJ fits an industrial control node that must combine network communication with deterministic local control. Its 16 MHz AVR core provides processing capacity for state-machine logic, while the integrated CAN V2.0A/V2.0B controller handles bus communication without requiring a separate CAN controller. The 53 general-purpose I/O lines can support discrete inputs, outputs, status indicators, and actuator interfaces, while four timer/counter blocks handle timing or PWM tasks. Two USARTs add service and diagnostic channels. Firmware must be checked for execution-time margin, and the CAN transceiver, termination, isolation, and protection network should be designed separately around the MCU pins.

🚗

Automotive CAN Interface Module

The AT90CAN128-16AJ is suitable for an automotive interface module that translates vehicle-network signals into a local control or diagnostic interface. Its CAN controller, 53 I/O lines, two USARTs, and four timers allow the module to handle communication, sensors, and discrete outputs in a compact 64-pin TQFP. The 16 MHz clock supports responsive protocol processing, while 128 KB of flash provides room for layered CAN stacks and application code. The exact ordering code must be checked against the vehicle's environmental requirements, and the PCB should include a protected transceiver interface rather than connecting MCU CAN pins directly to a physical bus.

🧩

Building Automation Sensor Hub

The AT90CAN128-16AJ can serve as a building-automation hub for collecting sensor data and distributing control commands over a CAN network. Its 4 KB SRAM supports message buffering and protocol state, while the 128 KB ISP flash accommodates application firmware and configuration logic. General-purpose I/O can monitor occupancy, temperature, door, or equipment-status inputs, and the timer/counter resources can support periodic sampling and output timing. A real-time counter is useful for event timestamping, while the two-wire serial interface can simplify configuration during installation. Firmware should account for the processing difference between the 16 MHz target and any 15 MHz replacement before timing-sensitive control is qualified.

🔧

Motor Control and PWM System

The AT90CAN128-16AJ is appropriate for a CAN-commanded motor or actuator controller where local timing must remain responsive. Four timer/counter blocks with compare modes and PWM support generate deterministic control signals, while the CAN controller receives motion commands and reports operating status. At 16 MHz, the AVR core can execute control loops, fault handling, and communication tasks, subject to the chosen PWM frequency and computation load. The 53 I/O lines provide flexibility for gate-control signals, position inputs, and fault flags. Validate timer prescaler calculations, interrupt latency, and update rates for the target firmware, especially if the design is considered for a 15 MHz family alternative.

🔧

CAN-Compatible Test and Measurement Instrument

The AT90CAN128-16AJ can support a compact test or measurement instrument that combines stimulus control with CAN-based reporting. Its 128 KB flash, 4 KB EEPROM, and 4 KB SRAM allow local configuration storage, acquisition buffering, and firmware updates, while the two USARTs provide independent communication paths for a host and peripheral equipment. Four timers support trigger, delay, and sampling functions, and the real-time counter can improve event timing. The CAN interface is useful for integrating the instrument with automated test systems. Engineers should budget interrupt and serial bandwidth, preserve deterministic timing under maximum peripheral activity, and validate analog measurement accuracy separately from the digital control subsystem.

🌐

Programmable CAN Gateway

The AT90CAN128-16AJ is well suited to a programmable gateway that receives CAN messages, applies routing or transformation rules, and exposes status through serial links. Its 16 MHz AVR processor, 53 I/O lines, two USARTs, and byte-oriented two-wire interface allow the gateway to bridge CAN with service ports or local configuration networks. The 128 KB program memory is useful for protocol tables and routing logic, while EEPROM can retain configuration settings when the application requires it. Message latency should be measured with realistic bus loading, and the design should include watchdog recovery, bus-error handling, and a controlled update path through the ISP interface.

Ringkasan Produk Direkomendasikan

AT90CAN64-16AJ AT90CAN family controller with lower program-memory capacity Digunakan di dalam: CAN-Based Industrial Control Node, Building Automation Sensor Hub, CAN-Compatible Test and Measurement Instrument, Programmable CAN Gateway AT90CAN128-16AU Microchip Technology Digunakan di dalam: CAN-Based Industrial Control Node, Automotive CAN Interface Module, CAN-Compatible Test and Measurement Instrument AT90CAN128-15AZ Microchip Technology Digunakan di dalam: Automotive CAN Interface Module, Motor Control and PWM System AT90CAN128-16AZ Same-speed family option with alternative ordering qualification Digunakan di dalam: Building Automation Sensor Hub, Programmable CAN Gateway AT90CAN128-15AJ Same-package 15 MHz option for lower-speed control tasks Digunakan di dalam: Motor Control and PWM System
What is the operating voltage of AT90CAN128-16AJ?
The AT90CAN128-16AJ operates from the voltage range specified for the AT90CAN128 family, with the exact minimum and maximum limits listed in the manufacturer datasheet. Its 16 MHz operating speed, 128 KB flash, and 4 KB SRAM identify it as the 16 MHz grade of the 90CAN device. Confirm the supply limits against the selected AT90CAN128 ordering code before finalizing a power supply or pin-level interface.
What are the key specifications of AT90CAN128-16AJ that engineers should know?
The AT90CAN128-16AJ is a 16 MHz 8-bit AVR RISC microcontroller with 128 KB of ISP flash, 4 KB of EEPROM, 4 KB of SRAM, 53 general-purpose I/O lines, and 32 working registers. It includes a CAN V2.0A/V2.0B controller, four timer/counter blocks, two USARTs, a real-time counter, and a byte-oriented two-wire serial interface. These resources are summarized on the Microchip AT90CAN128 product page.
Where can I download the AT90CAN128 datasheet PDF?
The AT90CAN128-16AJ documentation is available through the linked manufacturer product page and the AT90CAN128 datasheet PDF. The manufacturer page identifies the device as an AVR RISC-based microcontroller with 128 KB ISP flash, 4 KB EEPROM, 4 KB SRAM, 53 I/O lines, and a CAN 2.0A/V2.0B controller. Use the pin table and electrical characteristics from the manufacturer datasheet when assigning PCB tracks or selecting supply components.
Where can I find the AT90CAN128 pinout?
The AT90CAN128 pinout is shown in the pin-description table of the manufacturer AT90CAN128 datasheet, which covers the 64-pin TQFP device used by AT90CAN128-16AJ. Start with the numbered package drawing, then trace power, ground, reset, clock, programming, general-purpose I/O, and CAN interface assignments from that table. The package drawing is also useful for confirming the 14 mm by 14 mm footprint before fabrication.
Is AT90CAN128-16AJ suitable for CAN-based industrial equipment?
The AT90CAN128-16AJ is suitable for CAN-based industrial equipment because it combines a 16 MHz AVR core with a CAN V2.0A/V2.0B controller, 53 I/O lines, four timers, two USARTs, and serial programming. It can manage local control functions and network messaging in one package. For industrial use, verify the exact temperature grade and voltage limits against the manufacturer ordering information.
How do I program the AT90CAN128?
The AT90CAN128 supports programming through its in-system programming interface because its 128 KB program memory is specified as ISP flash. The procedure, interface signals, clocking requirements, and fuse settings should be taken from the AVR programming documentation and the device datasheet. Preserve access to the programming pins in the PCB layout if field updates or manufacturing firmware loading are required.
What is the difference between AT90CAN128-16AJ and AT90CAN128-16AU?
The AT90CAN128-16AJ and AT90CAN128-16AU are both identified as 16 MHz versions with 128 KB flash in 64-pin TQFP packages. Their practical distinction is the ordering-code temperature qualification and associated ordering conditions, which should be checked in the manufacturer product table. AT90CAN128-16AU can be considered for a pin-compatible design review, but the temperature range and lifecycle status must match the deployment requirement.
When should I choose AT90CAN128-16AJ over AT90CAN128-15AZ?
Choose AT90CAN128-16AJ when the design benefits from a 16 MHz clock, compared with the 15 MHz AT90CAN128-15AZ ordering option. The 6.7% clock increase can shorten execution time for polling, control loops, and CAN service routines, although timing must be recalculated. Both devices remain within the same AT90CAN128 family, making the change attractive when the faster grade meets environmental and supply requirements.
What can replace AT90CAN128-16AJ on an existing PCB?
AT90CAN128-16AU is the closest listed candidate for a pin-compatible replacement because it retains the 16 MHz speed and 64-pin TQFP arrangement. AT90CAN128-15AZ is another same-package option, but its 15 MHz clock is approximately 6.7% slower. Before replacing the device, compare temperature grade, supply voltage, pin functions, memory organization, programming procedure, and any errata applicable to the chosen ordering code.
Is AT90CAN128-16AJ the same as ATMEGA128-16AU?
No. The AT90CAN128-16AJ includes a CAN V2.0A/V2.0B controller and belongs to the AVR 90CAN family, while the ATMEGA128-16AU belongs to the related ATmega family without the same integrated CAN function. Although both use AVR architecture and 128 KB flash, their peripheral resources and pin functions differ. They should not be treated as equivalent without a complete pin and peripheral-function review.
Can AT90CAN64-16AJ replace AT90CAN128-16AJ?
The AT90CAN64-16AJ can be evaluated as a same-package AT90CAN-family alternative, but its lower program-memory capacity changes the amount of application code it can hold. The target AT90CAN128-16AJ provides 128 KB of flash, 4 KB of EEPROM, and 4 KB of SRAM. Replacement therefore requires checking code size, data usage, CAN peripheral behavior, and whether all required pin functions remain available.
What is the best Microchip equivalent for AT90CAN128-16AJ?
The closest same-manufacturer ordering candidate identified for a drop-in design review is AT90CAN128-16AU, which uses the 64-pin TQFP package and retains a 16 MHz clock and 128 KB flash. The AT90CAN128-15AZ is another same-package choice when a 15 MHz clock is acceptable. No verified cross-manufacturer equivalent was established, so a cross-brand replacement should not be assumed.
Where to buy AT90CAN128-16AJ online?
Use the Request a Quote form on this page to request AT90CAN128-16AJ pricing, current inventory, packaging, and delivery information. The form allows procurement teams to specify quantity and traceable sourcing requirements without relying on a static listing. For production quantities, request date codes, lot traceability, and confirmation that the exact AT90CAN128-16AJ ordering code will be supplied.
What is the price of AT90CAN128-16AJ?
Current AT90CAN128-16AJ pricing depends on quantity, package, date code, and market conditions, so it should be obtained through the Request a Quote form on this page. Enter the required quantity and packaging preference to receive a current quotation for the exact 64-pin TQFP ordering code. A production request should also state whether factory traceability or an unbroken manufacturing lot is required.
What is the lead time and stock status for AT90CAN128-16AJ?
Current stock and lead time for AT90CAN128-16AJ should be confirmed through the Request a Quote form on this page. Include your required quantity, approved date-code policy, target delivery date, and packaging needs in the request. If the exact ordering code is unavailable, ask whether the manufacturer can quote an alternate grade and document the required qualification review.

Data referensi engineering untuk AT90CAN128-16AJ — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose AT90CAN128-16AJ when a design requires a 16 MHz AVR controller, 128 KB of flash, 4 KB of SRAM, 4 KB of EEPROM, and an integrated CAN V2.0A/V2.0B controller in a 64-pin TQFP. AT90CAN128-16AU is the closest same-speed ordering option and should be selected only after its temperature qualification and lifecycle requirements are confirmed. Use AT90CAN128-15AZ or AT90CAN128-15AJ when a 15 MHz clock is sufficient and can absorb the approximately 6.7% reduction in processing rate; recalculate control, communication, and timeout timing. AT90CAN64-16AJ can reduce memory requirements, but its lower flash capacity requires an application-size review. No verified cross-manufacturer drop-in replacement was established. For every candidate, confirm pin assignments, operating voltage, temperature range, CAN electrical behavior, programming compatibility, and errata before approving a substitution.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini AT90CAN128-16AU AT90CAN128-15AZ AT90CAN128-15AJ AT90CAN128-16AZ AT90CAN64-16AJ
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 64-pin TQFP, 14 mm x 14 mm 64-pin TQFP, 14 mm x 14 mm 64-pin TQFP, 14 mm x 14 mm 64-pin TQFP, 14 mm x 14 mm 64-pin TQFP, 14 mm x 14 mm 64-pin TQFP, 14 mm x 14 mm
Maximum Clock Frequency 16 MHz 16 MHz 15 MHz 15 MHz 16 MHz 16 MHz
Flash Memory 128 KB 128 KB 128 KB 128 KB 128 KB 64 KB
CAN Controller CAN V2.0A and V2.0B compatible CAN V2.0A and V2.0B compatible CAN V2.0A and V2.0B compatible CAN V2.0A and V2.0B compatible CAN V2.0A and V2.0B compatible CAN V2.0A and V2.0B compatible
General-Purpose I/O Lines 53 lines 53 lines 53 lines 53 lines 53 lines 53 lines

Diferensiator Kunci

  • Higher clock speed within the same package (vsAT90CAN128-15AZ)
  • Full 128 KB program-memory capacity (vsAT90CAN64-16AJ)
  • Single-device CAN and serial integration (vsATMEGA128-16AU)

Catatan Desain

Route the CAN RX and TX signals from the AT90CAN128-16AJ to the pins of a suitable CAN transceiver; the MCU pins are logic-level interface signals and must not connect directly to the physical CAN bus. Place the transceiver close enough to the connector or bus interface to minimize exposed high-speed differential routing. Keep transceiver supply filtering and protection close to their associated pins, and observe the manufacturer's recommended grounding and isolation arrangement.

Use the 64-pin TQFP pin table and footprint drawing as the authoritative source for every connection. Place decoupling capacitors at the supply pins with very short return paths to the ground plane, and keep clock and reset traces away from CAN RX/TX and other switching nodes. The package has fine-pitch leads, so verify pad dimensions, solder mask clearance, paste stencil apertures, and the board's assembly orientation against the manufacturer drawing before releasing production files.

Do not treat AT90CAN128-16AU, AT90CAN128-15AZ, or another AT90CAN member as an unconditional substitute. Although the candidates use the same 64-pin TQFP arrangement, clock speed, ordering-code qualification, memory capacity, and family-specific behavior can affect production suitability. Re-run timing analysis when changing from 16 MHz to 15 MHz, check code size when moving to the 64 KB AT90CAN64 option, and verify all pin functions against the exact replacement datasheet.

The AT90CAN128-16AJ combines a 16 MHz core, CAN controller, timers, and serial peripherals, so supply design must account for both active processing and peripheral current. Follow the manufacturer datasheet for recommended capacitors, clock components, reset behavior, and supply sequencing. Confirm that the regulator has adequate transient response for digital switching while avoiding excessive routing impedance between the supply source and the device.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The manufacturer product page and ordering documentation should be checked for the definitive RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status of AT90CAN128-16AJ.

Pencarian Terkait

at90can128 datasheet at90can128 pinout at90can128 16au datasheet at90can128 programming at90can128 development board at90can128 pdf AT90CAN128-16AJ datasheet AT90CAN128-16AJ pinout AT90CAN128-16AJ programming AT90CAN128-16AJ equivalent AT90CAN128-16AJ replacement AT90CAN128-16AJ vs AT90CAN128-16AU Microchip AT90CAN128-16AJ AT90CAN128-16AJ price

Komponen dan Istilah Terkait

Microchip Technology AT90CAN128-16AJ AT90CAN128 AT90CAN128-16AU AT90CAN128-15AZ AT90CAN128-15AJ AT90CAN128-16AZ AT90CAN64-16AJ ATMEGA128-16AU AVR enhanced RISC core 8-bit microcontroller microcontroller embedded controller semiconductor CAN controller CAN V2.0A CAN V2.0B controller area network ISP flash memory EEPROM SRAM general-purpose I/O USART two-wire serial interface timer/counter real-time counter PWM 64-pin TQFP TQFP package family surface mount SMD
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ