ATF22V10CQ-15JU - 500-Gate 5V SPLD | Microchip Technology
Teilenummer: ATF22V10CQ-15JU ✓ AktivATF22V10CQ-15JU Übersicht
A simple programmable logic device, or SPLD, is a user-programmable semiconductor that implements fixed Boolean functions through an AND-OR architecture. In the broader electronics hierarchy, an SPLD sits below a field-programmable gate array and above discrete gate arrays. It is programmed to implement address decoding, control sequencing, interface translation, and other fixed logic functions, then stores that configuration in electrically erasable Flash memory.
The ATF22V10CQ-15JU provides 10 macrocells, approximately 500 gates, a 15 ns speed designation, and operation from a 5V supply. The device family supports speeds down to 5 ns and typical standby power dissipation as low as 10 µA. Its nonvolatile Flash configuration allows the programmed logic to remain available without repeatedly loading a program after power is removed.
The electrically erasable CMOS implementation combines configurable logic density with low-power operation and 5V compatibility. The Q family designation identifies the qualified product family covered by the manufacturer datasheet, while the 15 speed grade and JU ordering code identify the specific performance and package configuration. These devices are useful when the logic requirement is stable, the design benefits from simple in-system programmability, and a full FPGA would add unnecessary cost or complexity.
Typical uses include peripheral address decoding, bus-interface arbitration, industrial control sequencing, legacy data-acquisition interfaces, and glue logic around older processors. In each case, the device replaces multiple gates and state-holding elements with one programmable component while retaining deterministic propagation timing. The 10 user I/O pins also make the device appropriate for compact control and status interfaces.
A critical implementation consideration is that the existing design must use the manufacturer pin-assignment and programming conventions for the ATF22V10C family. Confirm the PLCC footprint, supply decoupling, programming access, and unused I/O states in the manufacturer datasheet before releasing a new PCB. Any replacement must preserve the 28-pin PLCC footprint and the required 15 ns timing behavior.
This product page combines the manufacturer device description, catalog package details, drop-in alternatives, comparison parameters, and practical validation guidance. It is designed to help engineers evaluate ATF22V10CQ-15JU for legacy PLD upgrades, board repairs, and new designs that benefit from compact nonvolatile programmable logic.
Drop-in-Alternativen für ATF22V10CQ-15JU – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
ATF22V10C-15JU
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATF22V10CQ-15JI
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATF22V10CQ-15JC
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATF22V10CQ-15SI
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATF22V10CQ-15JU Grenzwerte & elektrische Eigenschaften
| Device Type | Electrically Erasable CMOS Programmable Logic Device (SPLD) |
| Architecture | Simple PLD with AND-OR logic architecture |
| Configuration Memory | Electrically erasable Flash memory |
| Logic Density | 500 gates |
| Macrocells | 10 macrocells |
| User I/O Pins | 10 I/O pins |
| Maximum Operating Frequency | 83.3 MHz |
| Speed Grade | 15 ns |
| Versorgungsspannung | 5 V nominal |
| Industrial Supply Range | 5 V ±10% |
| Minimum Standby Current | 10 µA typical at family level |
| Gehäuse | 28-pin PLCC, 11.51 mm × 11.51 mm |
| Lead Pitch | 1.27 mm |
| Lead Geometry | J-bend leads |
| Package Code | S-PQCC-J28 |
| Montageart | Surface mount through PLCC socket or board layout |
| Delivery Format | Tube |
ATF22V10CQ-15JU s-pqcc-j28 Pinbelegungsleitfaden
Pinbelegung für ATF22V10CQ-15JU (s-pqcc-j28-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für ATF22V10CQ-15JU.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ATF22V10CQ-15JU ist geeignet für 6 Anwendungs: Legacy Processor Address Decoding, Industrial Control Sequencing, Data-Acquisition Interface Control, Bus Arbitration and Handshake Logic, Instrument Panel Control Logic, Legacy Interface Repair and Replacement.
Legacy Processor Address Decoding
The ATF22V10CQ-15JU fits processor address decoding because its 10 macrocells and approximately 500 gates can implement multiple chip-select or peripheral-enable equations at a 15 ns speed grade. Place the device between the processor address bus and peripheral control signals, then program the required Boolean terms for each decode region. The electrically erasable Flash configuration preserves the decoding map across power cycles, while the 5V supply and 28-pin PLCC package support established legacy control boards. Validate address setup and output timing against the processor interface before production, especially when the original design uses edge-sensitive latches or unusual active levels.
Empfohlen
Industrial Control Sequencing
ATF22V10CQ-15JU is suitable for fixed industrial control sequences where several interlocks, state transitions, and actuator commands must operate deterministically. Its 10 macrocells provide logic capacity for state-holding and combinational decoding, and the 15 ns grade supports precise propagation control in equipment-control paths. The 5V operating point fits systems designed around legacy TTL or CMOS control logic, while nonvolatile Flash programming simplifies field updates to the logic equations. Use the manufacturer programming and pin-assignment information, and verify input levels, reset behavior, and output states during power-up testing.
Empfohlen
Data-Acquisition Interface Control
The ATF22V10CQ-15JU can control fixed data-acquisition front ends by generating converter enables, channel-selection signals, timing gates, and status multiplexing. Ten user I/O pins allow the device to bridge several slow control lines without occupying a full microcontroller or FPGA. Its approximately 500-gate capacity is appropriate for stable acquisition sequences that do not require adaptive software control, and the 15 ns speed grade provides useful timing margin relative to many legacy peripheral interfaces. During board bring-up, verify signal polarity, interlock timing, and the behavior of every output when the acquisition system is reset or unpowered.
Empfohlen
Bus Arbitration and Handshake Logic
ATF22V10CQ-15JU fits deterministic bus-arbitration tasks that combine request, grant, busy, and ready signals into defined logic equations. The 10 macrocells provide enough parallel I/O for compact handshake networks, while the electrically erasable Flash configuration makes the arbitration map reproducible and easy to update. A 15 ns device grade is suitable for many older processor and peripheral buses when the design is checked against the slowest participating device. Use the exact ATF22V10C programming convention, keep contention paths short, and test simultaneous request conditions to prevent an invalid grant state.
Empfohlen
Instrument Panel Control Logic
The ATF22V10CQ-15JU can implement indicator sequencing, switch decoding, lamp blanking, and panel interlocks in legacy test and measurement equipment. Its 10 user I/O pins support several panel inputs and outputs, and the approximately 500-gate architecture is sufficient for fixed front-panel behavior without a processor. Nonvolatile configuration avoids repeating panel logic programming after every service visit. Because the PLCC package is intended for socketed or carefully handled surface-mount assembly, protect the leads during replacement and confirm that output states remain safe during reset, programming, and supply ramp conditions.
Empfohlen
Legacy Interface Repair and Replacement
ATF22V10CQ-15JU is particularly useful for repairing older control boards whose original programmable logic has become difficult to source. The 28-pin PLCC footprint, 10-macrocell architecture, 15 ns speed grade, and 5V supply allow an existing board to retain its established logic and timing. ATF22V10C-15JU offers the closest base-family drop-in, while other verified suffix variants can be evaluated when their qualification and temperature limits meet the equipment specification. After replacement, confirm the programmed configuration, verify every I/O under reset conditions, and run the original board-level functional test before returning the equipment to service.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ATF22V10CQ-15JU – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ATF22V10C-15JU | ATF22V10CQ-15JI | ATF22V10CQ-15JC | ATF22V10CQ-15SI |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-PLCC (11.51 mm × 11.51 mm) | 28-PLCC, same footprint | 28-PLCC, same footprint | 28-PLCC, same footprint | 28-PLCC, same footprint |
| Logic Density | 500 gates | 500 gates | 500 gates | 500 gates | 500 gates |
| Macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells | 10 macrocells |
| User I/O | 10 I/O pins | 10 I/O pins | 10 I/O pins | 10 I/O pins | 10 I/O pins |
| Speed Grade | 15 ns | 15 ns | 15 ns | 15 ns | 15 ns |
| Maximum Operating Frequency | 83.3 MHz | 83.3 MHz | 83.3 MHz | 83.3 MHz | 83.3 MHz |
| Supply Voltage | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal | 5 V nominal |
| Configuration Memory | Electrically erasable Flash memory | Electrically erasable Flash memory | Electrically erasable Flash memory | Electrically erasable Flash memory | Electrically erasable Flash memory |
| Qualification Code | Q-family ordering code | Base ATF22V10C ordering code | Q-family ordering code with I suffix | Q-family ordering code with C suffix | Q-family ordering code with S suffix |
Wichtigste Unterscheidungsmerkmale
- Combines a 500-gate architecture with 10 user I/O pins in a 28-pin PLCC (vs. ATF22V10C-15JU)
- Provides the same verified core logic parameters as the base-family drop-in (vs. ATF22V10C-15JU)
- Uses nonvolatile electrically erasable Flash configuration (vs. ATF22V10CQ-15JI)
Designhinweise
Use the manufacturer’s 28-pin PLCC footprint and 1.27 mm lead pitch rather than a generic DIP-28 land pattern. The PLCC body measures 11.51 mm × 11.51 mm and uses J-bend leads, so its pad geometry, lead length, and body clearance differ from a through-hole DIP. Confirm every power, ground, programming, and I/O net against the ATF22V10C(Q) pin-description table before PCB release.
Decouple the 5V supply close to the PLCC power pins, and route ground returns directly to the device ground pins rather than through peripheral-current paths. The ATF22V10C family is specified around a 5V nominal supply, with the industrial range stated as 5V ±10%. Check power-sequencing behavior and signal states during ramp because the programmed outputs may not remain valid until the supply and configuration conditions meet the manufacturer requirements.
Do not treat same-package suffix variants as automatically interchangeable for every program. The ATF22V10C-15JU, ATF22V10CQ-15JI, ATF22V10CQ-15JC, and ATF22V10CQ-15SI retain the same core logic density and 15 ns grade, but qualification and temperature requirements can differ. Confirm the ordering-code limits, load the correct programming file, and verify output states at power-up and reset before approving a substitution.
Compliance-Informationen
The manufacturer documentation identifies the ATF22V10C(Q) family, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was established for this ordering code.