ATMEGA8535-16PU - 8-bit AVR MCU 16MHz 8KB Flash | Microchip
Teilenummer: ATMEGA8535-16PU ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $2.88 | $2,88 |
| 10 | $2.65 | $26,50 |
| 100 | $2.42 | $242,00 |
| 500 | $2.2 | $1.100,00 |
| 1.000 | $2.05 | $2.050,00 |
ATMEGA8535-16PU Übersicht
A microcontroller unit (MCU) is a complete computing system on a single chip, combining a processor core, program memory, data memory, and peripherals. The ATmega8535 belongs to the AVR 8-bit MCU family (MCU -> 8-bit MCU -> AVR ATmega -> Microchip AVR), which uses an advanced RISC architecture with 130 powerful instructions, most of which execute in a single clock cycle, plus 32 general-purpose working registers directly connected to the ALU.
Key features include 8 KB self-programmable Flash with read-while-write support, 512 B EEPROM for non-volatile data storage, 512 B SRAM, and 32 general-purpose I/O lines. Peripheral integration is strong for its class: a serial programmable USART, SPI serial interface, three flexible Timer/Counters with compare and PWM modes, an 8-channel 10-bit ADC, programmable Watchdog Timer with on-chip oscillator, and an internal analog comparator.
Technically, the AVR Harvard architecture separates program and data buses, allowing simultaneous instruction fetch and execution. In-System Programming (ISP) via the SPI port and In-Application self-programming via the boot section eliminate dedicated programming cycles in production and allow firmware field updates. The ATmega8535 is also pin compatible with AT90S8535 and ATmega8515, easing migration on existing PCBs.
Typical applications include industrial automation and control, embedded systems, consumer electronics, motor control using PWM timer outputs, and sensor acquisition systems leveraging the 10-bit ADC.
A key design consideration: the 16 MHz rating applies only at 4.5 V to 5.5 V; at lower voltages the maximum safe frequency drops, so match supply rails and fuses carefully.
This page synthesizes distributor pricing, drop-in alternatives, practical design notes, and pinout data not consolidated in the manufacturer datasheet.
Drop-in-Alternativen für ATMEGA8535-16PU – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ATMEGA8535-16PU (gleiche Bauform und Footprint) – abweichend in Package, Instructions, Operating Temperature, Communication Interfaces, EEPROM.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
ATMEGA8535-16PI
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$1.65 / Stück
Datenblatt ansehen →ATMEGA8515-16PU
✅ Drop-In✓ Auf Lager
$3.71 / Stück
Datenblatt ansehen →ATMEGA16A-PU
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATMEGA32A-PU
✅ Drop-In ⚠️ Spezifikationen ungeprüft✓ Auf Lager
$3.85 / Stück
Datenblatt ansehen →ATMEGA8535-16AJ
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
ATMEGA8535-16PU Grenzwerte & elektrische Eigenschaften
| Core Architecture | AVR 8-bit RISC |
| Max Clock Frequency | 16 MHz |
| Throughput | 16 MIPS at 16 MHz |
| Flash Program Memory | 8 KB (4K x 16) |
| SRAM | 512 B |
| EEPROM | 512 B |
| Versorgungsspannung | 4.5 V to 5.5 V |
| I/O Lines | 32 |
| ADC | 8-channel, 10-bit |
| Timers/Counters | 3 (two 8-bit, one 16-bit) |
| Communication Interfaces | USART, SPI |
| Analog Comparator | Yes, on-chip |
| Watchdog Timer | Programmable, with on-chip oscillator |
| Programming | In-System Programmable (ISP), self-programmable boot |
| Instructions | 130 powerful instructions, most single-cycle |
| Gehäuse | 40-PDIP (0.600 inch, 15.24 mm) |
| Montageart | Through-Hole |
| Betriebstemperatur | 0C to +70C (P suffix, commercial) |
| RoHS-Status | Compliant |
ATMEGA8535-16PU Pin-Konfiguration
| Pin 1 | PB0/XCK/T0 — Port B bit 0 / USART external clock / Timer0 counter input |
| Pin 2 | PB1/T1 — Port B bit 1 / Timer1 counter input |
| Pin 3 | PB2/INT2/AIN0 — Port B bit 2 / External interrupt 2 / Analog comparator positive input |
| Pin 4 | PB3/OC0/AIN1 — Port B bit 3 / Timer0 output compare / Analog comparator negative input |
| Pin 5 | PB4/SS — Port B bit 4 / SPI slave select |
| Pin 6 | PB5/MOSI — Port B bit 5 / SPI master output, slave input |
| Pin 7 | PB6/MISO — Port B bit 6 / SPI master input, slave output |
| Pin 8 | PB7/SCK/UCSK — Port B bit 7 / SPI serial clock |
| Pin 9 | RESET — Reset input, active low |
| Pin 10 | VCC — Digital supply voltage (4.5 V to 5.5 V) |
| Pin 11 | GND — Ground |
| Pin 12 | XTAL1 — Inverting oscillator amplifier input / internal clock input |
| Pin 13 | XTAL2 — Inverting oscillator amplifier output |
| Pin 14 | PD0/RXD — Port D bit 0 / USART receive input |
| Pin 15 | PD1/TXD — Port D bit 1 / USART transmit output |
| Pin 16 | PD2/INT0 — Port D bit 2 / External interrupt 0 |
| Pin 17 | PD3/INT1 — Port D bit 3 / External interrupt 1 |
| Pin 18 | PD4/OC1B — Port D bit 4 / Timer1 output compare B (PWM) |
| Pin 19 | PD5/OC1A — Port D bit 5 / Timer1 output compare A (PWM) |
| Pin 20 | PD6/ICP1 — Port D bit 6 / Timer1 input capture |
| Pin 21 | PD7/OC2 — Port D bit 7 / Timer2 output compare (PWM) |
| Pin 22 | PC0/SCL — Port C bit 0 / Two-wire serial clock |
| Pin 23 | PC1/SDA — Port C bit 1 / Two-wire serial data |
| Pin 24 | PC2/TCK — Port C bit 2 / JTAG test clock |
| Pin 25 | PC3/TMS — Port C bit 3 / JTAG test mode select |
| Pin 26 | PC4/TDO — Port C bit 4 / JTAG test data output |
| Pin 27 | PC5/TDI — Port C bit 5 / JTAG test data input |
| Pin 28 | PC6/TOSC1 — Port C bit 6 / Timer2 oscillator input (32.768 kHz RTC) |
| Pin 29 | PC7/TOSC2 — Port C bit 7 / Timer2 oscillator output |
| Pin 30 | AVCC — ADC supply voltage; connect to VCC via low-pass filter |
| Pin 31 | GND — Ground |
| Pin 32 | AREF — ADC analog reference voltage |
| Pin 33 | PA7/ADC7 — Port A bit 7 / ADC channel 7 |
| Pin 34 | PA6/ADC6 — Port A bit 6 / ADC channel 6 |
| Pin 35 | PA5/ADC5 — Port A bit 5 / ADC channel 5 |
| Pin 36 | PA4/ADC4 — Port A bit 4 / ADC channel 4 |
| Pin 37 | PA3/ADC3 — Port A bit 3 / ADC channel 3 |
| Pin 38 | PA2/ADC2 — Port A bit 2 / ADC channel 2 |
| Pin 39 | PA1/ADC1 — Port A bit 1 / ADC channel 1 |
| Pin 40 | PA0/ADC0 — Port A bit 0 / ADC channel 0 |
Typische Anwendungen
ATMEGA8535-16PU ist geeignet für 6 Anwendungs: Industrial Automation and Control, Sensor Acquisition and Data Logging, Legacy AT90S8535 PCB Migration, Educational and Hobbyist Embedded Systems, Motor Control and PWM Systems, Consumer Electronics Embedded Control.
Industrial Automation and Control
The ATMEGA8535-16PU fits industrial control nodes that combine digital sequencing with analog monitoring: its 16 MHz AVR core delivers 16 MIPS for deterministic control loops, 32 GPIO lines drive relays, contactors, and indicator banks directly, and the 8-channel 10-bit ADC samples 0-5 V process signals such as pressure, level, and temperature from external transducers. The three timers with compare outputs generate PWM for heater or pump control, while the USART links to SCADA gateways. The 512 B EEPROM stores calibration constants and setpoints across power cycles. Because the 5 V rail matches legacy industrial I/O standards, level shifting is eliminated, and the watchdog timer guarantees recovery from transient faults in unattended equipment.
Empfohlen
Sensor Acquisition and Data Logging
For multi-channel sensor acquisition, the ATmega8535's 8-channel 10-bit ADC with AVCC and AREF reference pins (pins 30 and 32 on PORTA, ADC0-ADC7) digitizes up to eight analog sensors with a resolution of approximately 4.9 mV per LSB on a 5 V reference. The USART streams readings to a host PC or GSM module, and the SPI port interfaces external EEPROM or SD-card media for local logging beyond the on-chip 512 B EEPROM. Timer-driven ADC triggering produces jitter-free sampling intervals. The part suits environmental monitoring, battery-stack probes, and portable instrumentation where the PDIP package allows quick socketed prototyping and field module replacement without reflow equipment.
Empfohlen
Legacy AT90S8535 PCB Migration
The ATmega8535 was designed explicitly as the successor to the AT90S8535: Microchip documents that it is pin compatible and can replace AT90S8535 on existing printed circuit boards, enabling drop-in repair of discontinued-stock systems. The S8535C fuse programs compatibility behavior, though fuse-bit locations and electrical characteristics differ and must be re-verified per the datasheet. Engineers maintaining servo controllers, test fixtures, or consumer products built around AT90S8535 can use ATMEGA8535-16PU in the same 40-PDIP socket, reflash the application with minor timing adjustments, and restore full functionality while gaining ISP programming and self-programming boot capability absent from the original part.
Empfohlen
Educational and Hobbyist Embedded Systems
The 40-PDIP through-hole package makes ATMEGA8535-16PU ideal for education: it solders to single- or double-sided prototype boards, inserts into ZIF sockets for repeated reuse, and tolerates hand rework by beginners. The AVR architecture - 130 mostly single-cycle instructions and 32 working registers - is widely taught in university microcontroller courses, and the open-source AVR-GCC toolchain plus the MightyCore Arduino hardware package support ATmega8535 directly, enabling Arduino-IDE development. The 8-channel ADC, PWM timers, USART, and SPI expose all classic embedded concepts (analog input, motor control, serial communication) on one 5 V-tolerant chip, and its roughly $3 unit price keeps course kit budgets low.
Empfohlen
Motor Control and PWM Systems
The ATmega8535 provides four PWM-capable compare outputs: OC0 on pin PB3, OC1A on PD5, OC1B on PD4, and OC2 on PD7, driven by three timers with phase-correct and fast PWM modes. This enables dual-motor H-bridge control with independent speed channels at up to 16 MHz timer resolution for fine duty-cycle control. The external interrupt pins INT0/INT1/INT2 (PD2, PD3, PB2) capture quadrature encoder feedback, while the analog comparator supports zero-cross detection for brushless commutation. The 10-bit ADC samples motor current shunts for overload protection. Designs should route MOSFET gate drivers close to the PWM pins and validate the 5 V logic thresholds against the chosen driver ICs.
Empfohlen
Consumer Electronics Embedded Control
Cost-sensitive consumer products such as small appliances, toys, remote controls, and lighting controllers benefit from the ATmega8535's integration: one chip replaces discrete logic, timers, and an external ADC, reducing BOM count and assembly cost. The internal RC oscillator option eliminates the external crystal in timing-tolerant products, and the power-down sleep mode with watchdog wake-up keeps standby current low for battery-powered devices. The 5 V operation aligns with USB and legacy wall-adapter supplies. The PDIP package suits low-volume or hand-assembled production runs, while the TQFP ATMEGA8535-16AU variant scales the same firmware to automated SMT assembly when volumes grow.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ATMEGA8535-16PU – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ATMEGA8535-16PI | ATMEGA8515-16PU | ATMEGA16A-PU | ATMEGA32A-PU |
|---|---|---|---|---|---|
| Package | 40-PDIP (0.600 inch) | 40-PDIP (0.600 inch) - same | 40-PDIP (0.600 inch) - same | 40-PDIP (0.600 inch) - same | 40-PDIP (0.600 inch) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 8 KB | 8 KB | 8 KB | 16 KB | 32 KB |
| SRAM | 512 B | 512 B | 512 B | 1 KB | 2 KB |
| ADC | 8-channel, 10-bit | 8-channel, 10-bit | None | 8-channel, 10-bit | 8-channel, 10-bit |
| Max Clock Frequency | 16 MHz (at 4.5-5.5 V) | 16 MHz (at 4.5-5.5 V) | 16 MHz (at 4.5-5.5 V) | 16 MHz (at 4.5-5.5 V) | 16 MHz (at 4.5-5.5 V) |
| Operating Temperature | 0C to +70C (commercial) | -40C to +85C (industrial) | 0C to +70C (commercial) | -40C to +85C | -40C to +85C |
| GPIO Lines | 32 | 32 | 32 | 32 | 32 |
Wichtigste Unterscheidungsmerkmale
- Integrated 8-channel 10-bit ADC (vs. ATMEGA8515-16PU)
- Identical die and pinout in industrial temperature grade (vs. ATMEGA8535-16PI)
- Lower Flash may increase firmware pressure (vs. ATMEGA16A-PU)
Designhinweise
Supply the ADC separately through AVCC (pin 30): connect AVCC to VCC through a low-pass filter such as a 10 uH inductor or 100-ohm resistor with 100 nF to GND, and decouple AREF (pin 32) with a 100 nF capacitor when using the internal reference. Noisy digital ground currents flowing into the analog section are the most common cause of ADC noise floor degradation on this device. Per the Microchip ATmega8535 datasheet, ADC accuracy is only guaranteed when AVCC stays within 0.3 V of VCC.
Fuse settings, not code, cause most ATmega8535 bring-up failures. The clock source fuses (CKSEL bits) must match your hardware: an external 16 MHz crystal requires CKSEL programmed for the correct crystal range plus appropriate SUT start-up fuses. Programmers that flash code but leave CKSEL defaults will run the part on the wrong oscillator and appear dead. Additionally, when migrating from AT90S8535, remember fuse-bit locations differ between the two devices even though the PCB footprint is identical.
For the PDIP package, place a 100 nF ceramic decoupling capacitor within a few millimeters of pin 10 (VCC) to pin 11 (GND), and add a 10 uF bulk capacitor per board section. Keep the SPI programming header (MOSI, MISO, SCK, RESET on PB5-PB7 and pin 9) short and routed away from PWM traces on PD4/PD5/PD7, since in-circuit programming occurs while those outputs toggle. The 2.54 mm PDIP lead pitch makes hand prototyping straightforward, but insert a socket rather than soldering the MCU directly for firmware iterations.
Compliance-Informationen
RoHS compliance per distributor listings (DigiKey/Mouser). REACH, lead-free, halogen-free, and conflict-minerals status not explicitly stated in provided web data.
