ATSAMD51P20A-AU - 120MHz Cortex-M4F MCU | Microchip
Teilenummer: ATSAMD51P20A-AU ✓ AktivATSAMD51P20A-AU Übersicht
A microcontroller is a programmable system-on-chip that integrates a processor core, memory, and peripherals into one device. The ARM Cortex-M4F core provides a 32-bit instruction set and single-precision floating-point hardware, while the SAM D51 family extends that architecture with embedded flash, SRAM, communication interfaces, analog peripherals, and dedicated external-control hardware. This places the device in the hierarchy of embedded processor, microcontroller, and general-purpose control IC.
Principal features include a 120 MHz maximum clock speed, 1 MB of flash memory, up to 256 KB of SRAM with ECC, and a 128-lead TQFP package. The SAM D51 series is positioned for general-purpose applications that require more processing capability and I/O than small 8- or 16-bit controllers. USB, serial communications, and analog conversion capabilities make the device applicable to connected control systems, data acquisition, and industrial equipment.
The Cortex-M4F architecture supports efficient digital signal processing and real-time control while retaining a conventional microcontroller development model. Dual-panel flash with ECC improves the integrity of program storage, while ECC-protected SRAM supports reliable operation in systems where data integrity matters. The large peripheral mix reduces the need for external devices when implementing motor, communications, and measurement functions.
Typical uses include industrial automation, building and energy control, connected embedded products, medical and diagnostic equipment, and instrumentation. The 128-pin package provides a high peripheral count for designs that need numerous I/O, communication ports, timer channels, and analog inputs while remaining on a conventional surface-mount PCB.
When laying out a board, treat the 14 x 14 mm TQFP as a fine-pitch package and route power, ground, decoupling, and programming signals according to the Microchip pin-description and layout guidance. Verify the exact package pin mapping in the manufacturer datasheet before assigning signals, since alternate functions can be multiplexed across many of the 128 leads.
This page consolidates the verified device description, package and memory characteristics, drop-in order-code alternatives, and application-focused engineering guidance. It also distinguishes electrically equivalent ordering options from packages or device families that would require a different PCB footprint, helping designers assess replacement options before committing to a layout.
Drop-in-Alternativen für ATSAMD51P20A-AU – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit ATSAMD51P20A-AU (gleiche Bauform und Footprint) – abweichend in Flash Memory, Package.
ATSAMD51P20A-AF
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATSAMD51P20A-AZ
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATSAMD51P20A-AFT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATSAMD51P20A-AU-EFP
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ATSAMD51P20A-AU Grenzwerte & elektrische Eigenschaften
| Product Type | 32-bit ARM Cortex-M4F microcontroller |
| Manufacturer | Microchip Technology |
| Series | SAM D51 |
| CPU Core | ARM Cortex-M4 with FPU |
| Maximum CPU Frequency | 120 MHz |
| Flash Memory | 1 MB (1M x 8) |
| Flash Architecture | Dual-panel flash with ECC |
| Maximum SRAM | 256 KB with ECC |
| Betriebsversorgungsspannung | 3.3 V |
| Gehäuse | 128-lead TQFP (14 x 14 mm) |
| Montageart | Surface mount |
| Maximum Temperature | 85 °C |
| Interface Feature | USB |
| Bit Width | 32 bit |
| Processor Core | ARM Cortex-M4F |
ATSAMD51P20A-AU 128-lead tqfp (14 x 14 mm) Pinbelegungsleitfaden
Pinbelegung für ATSAMD51P20A-AU (128-lead tqfp (14 x 14 mm)-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für ATSAMD51P20A-AU.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
ATSAMD51P20A-AU ist geeignet für 6 Anwendungs: Industrial Automation Controller, Connected Sensor Gateway, Real-Time Signal Conditioning, Building and HVAC Control, Medical and Diagnostic Instrumentation, Motor and Power System Control.
Industrial Automation Controller
The ATSAMD51P20A-AU fits industrial automation controllers that combine real-time control with network-facing communications. Its ARM Cortex-M4F core operates up to 120 MHz, providing headroom for control loops, communications stacks, and supervisory logic, while 1 MB of flash supports a bootloader and substantial application firmware. ECC-protected dual-panel flash and up to 256 KB of SRAM improve reliability where control state must be preserved. The 128-lead TQFP also exposes a broad set of I/O for sensors, actuators, and field-bus transceivers. Firmware should use hardware timestamp counters and timers for deterministic sampling, while the board must provide clean decoupling, local analog ground partitioning, and robust ESD protection on externally accessible lines.
Empfohlen
Connected Sensor Gateway
The ATSAMD51P20A-AU is appropriate for a connected sensor gateway that aggregates readings from multiple peripherals and forwards them over USB or another serial interface. The 120 MHz Cortex-M4F core can process protocol framing and filtering while leaving resources for local data acquisition. With 1 MB of dual-panel flash with ECC, the device provides ample room for firmware, configuration, and diagnostic data, and the SRAM supports packet buffering. Its 128-lead package makes numerous I/O available for SPI and I2C sensor buses without requiring large external interface expanders. A practical design should isolate analog inputs from switching regulators, route communications away from high-current outputs, and validate the USB or communications power path against the system load.
Empfohlen
Real-Time Signal Conditioning
The ATSAMD51P20A-AU suits real-time signal-conditioning and digital-filtering modules because the Cortex-M4F core combines a 32-bit pipeline with hardware single-precision floating-point support at up to 120 MHz. The floating-point unit accelerates filtering, calibration, and control algorithms without requiring a separate DSP. Its 1 MB flash provides room for lookup tables and complex algorithms, while ECC-protected SRAM supports working buffers. The 128-lead TQFP offers sufficient pin count for analog inputs, timer channels, and external memory or communications interfaces. For accurate results, keep the analog front end local to the MCU, use a separate analog supply section, and allow for settling time between acquisition and conversion rather than processing immediately after each edge.
Empfohlen
Building and HVAC Control
The ATSAMD51P20A-AU can serve as the central controller in building and HVAC equipment that must manage sensors, relays, displays, and communications in one compact module. Its 120 MHz Cortex-M4F performance supports multitasking among control loops, user-interface updates, and network handling, and 1 MB of flash accommodates protocol stacks and field-service data. The 128-lead TQFP provides enough I/O for temperature inputs, fan or valve outputs, and serial transceivers. Because environmental and mains-adjacent interfaces are common in this application, the design should maintain separation between logic and power grounds, use transient-voltage protection on exposed wiring, and validate timing under full relay-load transients.
Empfohlen
Medical and Diagnostic Instrumentation
The ATSAMD51P20A-AU fits laboratory and diagnostic instrumentation requiring deterministic embedded control, data logging, and USB connectivity. The 120 MHz Cortex-M4F core can execute measurement algorithms and communicate with a host computer, while the ECC-protected flash and SRAM support dependable handling of calibration and operating data. The 128-lead TQFP provides a substantial pin budget for sensor inputs, status indicators, and isolated communication interfaces. In these systems, maintain analog and digital ground separation, use low-noise local regulation for sensitive measurement circuits, and validate leakage, isolation, and ESD requirements against the intended medical equipment category before production release.
Empfohlen
Motor and Power System Control
The ATSAMD51P20A-AU is suitable for coordinating motors, valves, and power-conversion peripherals in supervisory control systems. The 120 MHz Cortex-M4F core provides enough performance for PWM timing, current or position supervision, and fault handling, while the large peripheral count available in the 128-lead package simplifies mixed-signal connections. The 1 MB flash supports layered control firmware and field diagnostics. Design the PCB so switching nodes and motor traces remain physically separated from analog and communication nets, use dedicated gate-driver interfaces rather than driving loads directly from GPIO pins, and include current sensing and shutdown paths that operate independently of the main firmware loop.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für ATSAMD51P20A-AU – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | ATSAMD51P20A-AF | ATSAMD51P20A-AZ | ATSAMD51P20A-AFT | ATSAMD51P20A-AU-EFP |
|---|---|---|---|---|---|
| Package | 128-lead TQFP (14 x 14 mm) | 128-lead TQFP (14 x 14 mm) | 128-lead TQFP (14 x 14 mm) | 128-lead TQFP (14 x 14 mm) | 128-lead TQFP (14 x 14 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| CPU Core | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F | ARM Cortex-M4F |
| Maximum Frequency | 120 MHz | 120 MHz | 120 MHz | 120 MHz | 120 MHz |
| Flash Memory | 1 MB (1M x 8) | 1 MB | 1 MB | 1 MB | 1 MB |
| Maximum SRAM | 256 KB with ECC | 256 KB with ECC | 256 KB with ECC | 256 KB with ECC | 256 KB with ECC |
| USB Connectivity | USB | USB | USB | USB | USB |
| Ordering Configuration | -AU suffix | -AF suffix | -AZ suffix | -AFT suffix | -AU-EFP suffix with extended flash performance |
Wichtigste Unterscheidungsmerkmale
- High-performance Cortex-M4F control with substantial on-chip memory (vs. ATSAMD51P20A-AF)
- Same-footprint choice with extended flash performance (vs. ATSAMD51P20A-AU-EFP)
- Broad I/O and mixed-signal integration in one package (vs. ATSAMD51P20A-AZ)
Designhinweise
Place the MCU close to the supporting circuitry assigned by the pin-multiplexing plan, but keep analog, communications, and high-current interfaces in their own physical regions. Follow the manufacturer package drawings for the 14 x 14 mm TQFP land pattern, fanout, and exposed routing rules. The 128-lead footprint has a fine lead pitch, so use consistent pad geometry, check annular rings after fabrication, and verify that the assembly house can place the selected package without bridging.
Estimated: if the 3.3 V rail supplies a 20 mA load and the device's own current is not added, the rail dissipates about 66 mW in the MCU supply path. Actual total rail demand can be higher once peripherals and external I/O are included, so size the regulator and copper area for the complete board rather than the core alone. Keep high-current loads on separate branches and use local bulk and high-frequency decoupling at the device supply pins.
Route externally accessible serial, USB, and debug signals away from switching or motor nodes, and provide series damping where edge rates require it. Use a continuous ground plane where possible and avoid splitting return paths beneath high-speed nets. Because the TQFP leads are densely spaced, watch for accidental shorts during rework and use a microscope when inspecting fine-pitch soldering. Validate USB, clock, and programming interfaces with appropriate termination and test equipment.
Do not assume that every similarly suffixed SAM D51 order code is a purchasing substitute. The EFP option changes flash-performance characteristics, while AF, AZ, AFT, and AU can denote different grade or ordering configurations. Before replacement, compare the package drawing, temperature range, flash timing, qualification status, and programming documentation. Software should also be rebuilt and tested against the exact device revision selected for production.
Compliance-Informationen
The ATSAMD51P20A-AU is presented by Microchip as a current general-purpose microcontroller, but the verified device information does not state the individual RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Review the manufacturer product page and the applicable material-declaration documents before making a compliance claim.