Microchip Technology

ATSAML10D14A-YF - 32MHz Cortex-M23 MCU | Microchip

Teilenummer: ATSAML10D14A-YF ✓ Aktiv
1.62 V to 3.63 V Vdss Less than 25 uA/MHz Id 24-SSOP, 208 mil Package 32 MHz Speed 16 KB (16K x 8) Memory
MOQ: 1 |

ATSAML10D14A-YF Übersicht

The Microchip Technology ATSAML10D14A-YF is a 32-bit ARM Cortex-M23 microcontroller operating at 32 MHz, with 16 KB of Flash memory, 4 KB of SRAM, and 2 KB of EEPROM in a 24-SSOP package. It belongs to the SAM L10 family and combines low-power operation with capacitive-touch sensing and advanced analog peripherals.

A microcontroller is a programmable system-on-chip that integrates a processor core, memory, and peripherals into one device. The ARM Cortex-M23 core provides a compact 32-bit architecture with hardware integer arithmetic and efficient event handling. In the power hierarchy, the ATSAML10D14A-YF is a microcontroller within the broader category of embedded processors and mixed-signal semiconductors.

Key features include operation below 25 uA/MHz in active mode and below 100 nA in sleep mode, as stated by Microchip. The device also provides an enhanced peripheral touch controller, ADC, DAC, op amp, comparators, serial communications, and an ISO7816 smart-card interface. Its 16 KB Flash supports embedded firmware, while 4 KB of SRAM provides working memory for control loops, communication stacks, and user-interface logic.

The device uses the Microchip SAM L10 architecture and event system to coordinate asynchronous peripheral activity with low-power operation. Its 32 MHz processing rate gives designers enough performance for capacitive-touch interfaces, compact sensor nodes, low-cost security accessories, and industrial control modules without requiring a larger application processor. Multiple programmable peripheral functions also reduce the need for external analog and communication components.

Typical uses include capacitive-touch control panels, compact keypads, smart-card readers, security accessories, building controls, and small sensor nodes. The 24-SSOP package also supports assembly processes that can accommodate leaded rather than fine-pitch components, although board area remains greater than that of an equivalent VQFN package.

Designers should verify the exact peripheral pin mapping and power configuration in the manufacturer pin-description table before assigning PCB tracks. Place decoupling capacitors beside the supply pins, route sensitive analog inputs away from switching nodes, and use the sleep-mode characteristics as a starting point for battery-life calculations rather than a complete system power budget.

Drop-in-Alternativen für ATSAML10D14A-YF – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit ATSAML10D14A-YF (gleiche Bauform und Footprint) – abweichend in Active Mode Current, Package, RoHS Status, Sleep Mode Current.

Microchip Technology
Active Mode Current: < 25 uA/MHz
Package: 24-SSOP (YF)
RoHS Status: Compliant
Vergleichen mit ATSAML10D14A-YF →

ATSAML10D16A-YF

✅ Drop-In ⚠️ Spezifikationen ungeprüft
Microchip Technology
📦 24-SSOP
ARM Cortex-M23 · 32-bit · 32 MHz · 64 KB (64K x 8) · 16 KB · 1.62 V to 3.63 V · < 25 uA/MHz · < 100 nA

Preis auf Anfrage

Datenblatt ansehen →

ATSAML10D18A-YF

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 24-SSOP
Flash memory increases from 16 KB to 18 KB (+12.5%); SRAM and peripheral assignments require final datasheet verification

📋 Referenzalternative (nicht im Katalog)

ATSAML10D14A-YF Grenzwerte & elektrische Eigenschaften

Manufacturer Microchip Technology
Product Type ARM Cortex-M23 Microcontroller
CPU Core ARM Cortex-M23
Architecture SAM L10
Bit Width 32-bit
Maximum CPU Frequency 32 MHz
Flash Memory 16 KB (16K x 8)
SRAM 4 KB
EEPROM 2 KB
Active Mode Current Less than 25 uA/MHz
Sleep Mode Current Less than 100 nA
Supply Voltage Range 1.62 V to 3.63 V
Gehäuse 24-SSOP, 208 mil
Peripheral Interface SERCOM
Analog Peripherals ADC, DAC, OPAMP
Touch Controller Enhanced peripheral touch controller
Security Peripheral ISO7816 smart-card interface
RoHS-Status RoHS

ATSAML10D14A-YF 24-ssop, 208 mil Pinbelegungsleitfaden

Pinbelegung für ATSAML10D14A-YF (24-ssop, 208 mil-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.

Pinbelegungsdiagramm für ATSAML10D14A-YF im 24-ssop, 208 mil-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für ATSAML10D14A-YF.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

ATSAML10D14A-YF ist geeignet für 6 Anwendungs: Capacitive-Touch Control Panels, Smart-Card Readers and Access Controls, Battery-Powered Sensor Nodes, Industrial Control Modules, Connected Building Controls, Compact Security and Keypad Accessories.

🧩

Capacitive-Touch Control Panels

The ATSAML10D14A-YF fits compact keypad and control-panel designs because its enhanced peripheral touch controller is paired with a 32 MHz ARM Cortex-M23 core and a 16 KB Flash footprint. The controller can evaluate touch events while the application code manages lighting, feedback, and communication. Its 4 KB SRAM provides room for event buffering and interface state, while the 2 KB EEPROM supports nonvolatile configuration such as calibration offsets or device settings. A key engineering consideration is that the touch peripheral alone does not determine sensitivity; electrode geometry, guard-ring construction, PCB cleanliness, and grounding often have a greater effect than software filtering.

🔒

Smart-Card Readers and Access Controls

The ATSAML10D14A-YF is appropriate for compact smart-card readers because Microchip highlights its ISO7816 interface alongside the low-power Cortex-M23 core. It can coordinate card communication, request authentication, drive indicator feedback, and expose a host interface without requiring a separate security controller. The 16 KB Flash is suitable for a focused embedded application, and operation below 25 uA/MHz in active mode supports energy-conscious access hardware. The final design still requires careful treatment of the ISO7816 clock and data lines, plus the protection components specified by Microchip for exposed card-contact circuitry.

📱

Battery-Powered Sensor Nodes

The ATSAML10D14A-YF suits compact battery-operated sensor nodes because its sleep-mode current is specified below 100 nA and its active-mode consumption is below 25 uA/MHz. A design can wake on a timer or external interrupt, sample an analog channel, process the result, and return to sleep without continuously powering the CPU. The 1.62 V to 3.63 V operating range permits direct integration with low-energy rails, although the regulator's own quiescent current and sensor leakage must be included in the system budget. Firmware should disable unused peripherals and GPIO states aggressively to approach the manufacturer low-power figures in real hardware.

🏭

Industrial Control Modules

The ATSAML10D14A-YF can serve as the control processor in small industrial modules that require deterministic peripheral handling without the memory overhead of a larger MCU. SERCOM interfaces support flexible serial connectivity, while the ADC, DAC, op amp, and comparators provide local analog conditioning. Its 32 MHz Cortex-M23 core has ample capacity for event handling, state machines, and communication protocols within the available 16 KB Flash and 4 KB SRAM. Industrial equipment designers should still plan for transient protection, isolation requirements, and grounding discipline, because the MCU's internal analog block does not replace external protection at field-facing connectors.

🌐

Connected Building Controls

The ATSAML10D14A-YF is useful in connected thermostats, room controllers, and small building-automation nodes where a touch interface, analog sensing, and low-power operation must coexist. The enhanced touch controller can support local user interaction, while ADC and comparator resources handle simple sensing functions. SERCOM peripherals can bridge the controller to external transceivers or standardized building networks. Because the device offers only 16 KB of Flash and 4 KB of SRAM, designers should select a lightweight protocol stack and avoid moving protocol processing to a separate platform. The 24-SSOP package also makes the part suitable for higher-volume leaded-package assembly when fine-pitch leadless assembly is unnecessary.

🖥️

Compact Security and Keypad Accessories

The ATSAML10D14A-YF suits small keypad locks, credential readers, and portable security accessories that combine local input handling with smart-card communication. Its enhanced peripheral touch controller can support capacitive keys, and the ISO7816 interface provides a path to smart-card transactions. The Cortex-M23 core can run the device protocol and local user logic while its low-power modes help manage standby consumption. Designers should treat security-sensitive code, key storage, and authentication policy as separate architecture requirements rather than relying on the presence of an ISO7816 interface alone, and should verify the intended package pin mapping against the manufacturer datasheet before layout release.

What is the ATSAML10D14A-YF microcontroller?
The ATSAML10D14A-YF is a 32-bit SAM L10 microcontroller built around an ARM Cortex-M23 core and operating at 32 MHz. It provides 16 KB of Flash memory, 4 KB of SRAM, and 2 KB of EEPROM in a 24-SSOP package. Microchip identifies the device as combining low-power operation, capacitive-touch capability, advanced analog functions, and serial connectivity on a single embedded controller.
What are the key specifications of ATSAML10D14A-YF?
The principal specifications are a 32 MHz ARM Cortex-M23 core, 16 KB of Flash, 4 KB of SRAM, 2 KB of EEPROM, and a 1.62 V to 3.63 V operating range. The 24-SSOP package also exposes ADC, DAC, op-amp, SERCOM, capacitive-touch, and ISO7816 smart-card functions. These ratings make the part suitable for compact low-power control, touch, security, and sensor-node designs.
What is the active current consumption of ATSAML10D14A-YF?
The Microchip product page states that the ATSAML10D14A consumes less than 25 uA/MHz in active mode. At a 32 MHz operating point, that headline figure corresponds to less than 800 uA before peripheral and external-circuit loads are added. Actual consumption depends on clock gating, enabled peripherals, GPIO state, flash activity, and the voltage selected by the power-control configuration.
How much current does ATSAML10D14A-YF use in sleep mode?
The manufacturer specifies less than 100 nA in sleep mode for the ATSAML10 family device. This figure represents the controller's low-power state rather than the complete product's consumption. Board leakage, pull-up resistors, sensor standby current, and regulator quiescent current must be added when calculating battery life for a complete embedded system.
What peripherals are available on ATSAML10D14A-YF?
The ATSAML10D14A-YF includes an enhanced peripheral touch controller, ADC, DAC, op amp, SERCOM interfaces, and an ISO7816 smart-card interface. Microchip also highlights the device's event system and advanced analog capabilities. Exact channel counts, trigger mappings, and alternate-function assignments should be confirmed in the manufacturer pin-description and peripheral tables before PCB routing.
What is the difference between ATSAML10D14A-YF and ATSAML10D14A-MFT?
The principal documented difference is the package: ATSAML10D14A-YF is offered in 24-SSOP, while ATSAML10D14A-MFT is offered in 24-VQFN. Both are associated with the same ARM Cortex-M23 and 16 KB Flash MCU family, but their land patterns are not identical. A VQFN version therefore cannot replace the SSOP part on an unchanged PCB without a footprint and layout redesign.
What is the best drop-in replacement for ATSAML10D14A-YF?
A genuine drop-in replacement must use the 24-SSOP land pattern, match the 1.62 V to 3.63 V supply range, retain compatible core and peripheral assignments, and preserve the 16 KB Flash and 4 KB SRAM configuration. The ATSAML10D14A-MFT is not a drop-in option because it uses VQFN packaging. Use the Microchip product-selection and cross-reference tools to check any proposed alternative against pin count, package, memory, and peripheral requirements.
When should I choose ATSAML10D14A-YF instead of a VQFN MCU?
Choose the ATSAML10D14A-YF when the assembly process or connectorized module benefits from a 0.208-inch-lead SSOP footprint and when the board has sufficient area for the larger package. A VQFN alternative may be preferable where board area is tightly constrained or where the production line already handles fine-pitch leadless packages. Both electrical and PCB compatibility must be verified independently.
Is ATSAML10D14A-YF suitable for capacitive-touch applications?
Yes, the ATSAML10D14A-YF is suitable for capacitive-touch applications because Microchip identifies an enhanced peripheral touch controller as a principal feature. Its 32 MHz Cortex-M23 core can process touch-controller events and support a local user interface. Electrode design, channel count, sensitivity, calibration method, and grounding still require validation for the specific mechanical construction.
Can ATSAML10D14A-YF be used in a smart-card reader design?
Yes, the device includes an ISO7816 smart-card interface, making it applicable to compact smart-card readers, access-control accessories, and security modules. The interface should be connected according to the manufacturer application guidance, including the required external clock, signal conditioning, and protection components. Firmware must also implement the card protocol and security requirements appropriate to the product.
Where can I download the ATSAML10D14A-YF datasheet?
The manufacturer product page for ATSAML10D14A provides the authoritative device documentation and datasheet access. The Octopart datasheet page for ATSAML10D14A-YF is an additional discovery route. Use the Microchip page for the latest document revision, package drawings, pin descriptions, electrical characteristics, and errata relevant to the 24-SSOP ordering code.
Where can I find the ATSAML10D14A-YF pinout?
The ATSAML10D14A-YF pinout is published in the pin-description table of the manufacturer datasheet. Assign PCB nets from that table and the package drawing rather than from the physical appearance of the device alone. Pay particular attention to alternate-function multiplexing, the exposed supply requirements, ground pins, programming interface pins, and the analog-capable pins.
Where can I buy ATSAML10D14A-YF online?
Use the Request a Quote form on this page to ask for ATSAML10D14A-YF availability, current pricing, minimum order quantity, and lead time. The form also allows you to specify the required 24-SSOP ordering code and packaging preference. Confirm authorized-channel authenticity and the date on any quotation before placing a production order.
What is the price of ATSAML10D14A-YF?
Current ATSAML10D14A-YF pricing is generated through the Request a Quote form on this page because distributor prices and stock levels change by quantity, date, and channel. Submit the target quantity and required packaging to obtain a current quotation. For design budgeting, treat any historical listing amount only as an approximate reference and reconfirm before ordering.
What is the lead time and stock status of ATSAML10D14A-YF?
Request the current lead time and stock allocation through the Request a Quote form on this page. Lead time can vary with order quantity, scheduled production capacity, packaging, and regional inventory. Microchip's ATSAML10D14A product page is the appropriate place to confirm the device's lifecycle position before committing a long-term production design.
What tools and firmware support ATSAML10D14A-YF?
The ATSAML10D14A-YF is supported by Microchip's SAM device programming and software-development tools. The manufacturer product page provides links to the device documentation and development resources. Choose the debugger and programmer listed for the SAM L10 family, confirm SWD or supported programming-interface routing, and use the current Microchip development package for startup code and peripheral drivers.

Technische Referenzdaten für ATSAML10D14A-YF – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the ATSAML10D14A-YF when a project needs capacitive-touch sensing, local analog processing, ISO7816 connectivity, and low-power Cortex-M23 performance in a leaded 24-SSOP package. It is particularly attractive for smart-card readers, keypads, building-control nodes, and compact sensor modules where board area is less constrained than in a miniature wearable. Select the ATSAML10D16A-YF or ATSAML10D18A-YF family alternatives only after confirming that their pin functions, memory limits, clock settings, and operating characteristics remain acceptable. Do not use the 24-VQFN ATSAML10D14A-MFT as a board-level replacement for this SSOP device. For designs where leadless packaging and minimal PCB area are the priorities, compare a verified QFN family option and treat it as a new layout rather than a drop-in substitution.

Vergleich mit Alternativen

Parameter Dieses Produkt ATSAML10D16A-YF ATSAML10D18A-YF
Brand Microchip Technology Microchip Technology Microchip Technology
Package 24-SSOP 24-SSOP 24-SSOP
Pin Compatibility 24-SSOP reference footprint Same family and package; verify pin table before substitution Same family and package; verify pin table before substitution

Wichtigste Unterscheidungsmerkmale

  • Combines capacitive-touch sensing with advanced analog functions (vs. ATSAML10D14A-MFT)
  • Lower-power architecture for compact embedded products (vs. ATSAML10D14A-MFT)
  • Package suited to leaded-package assembly (vs. ATSAML10D14A-MFT)

Designhinweise

Use the less-than-25-uA/MHz active figure and less-than-100-nA sleep figure as component-level targets. Estimated active current at 32 MHz is below 800 uA before external loads are added, calculated from 32 MHz multiplied by 25 uA/MHz. Actual firmware should clock-gate unused blocks, disable unused GPIO pull resistors, and place the MCU into the deepest permitted sleep state during idle intervals. Include regulator quiescent current and sensor leakage in the complete battery budget.

Assign every net from the manufacturer pin-description table rather than relying on package position alone. Place the required bypass capacitors adjacent to the device's supply pins, provide a clean return path for analog and touch channels, and keep high-current or switching traces away from sensitive inputs. The 24-SSOP footprint has 0.208-inch lead spacing, so confirm board outline, drill placement, solderability, and assembly clearances against the current package drawing.

Do not substitute ATSAML10D14A-MFT for this part on an existing board: its VQFN land pattern is not compatible with the 24-SSOP footprint. Also avoid assuming that all family variants share the same exposed-pin functions, alternate-function routing, or maximum clock settings. Before releasing a substitution, compare the ordering code, package drawing, pin table, memory configuration, operating-voltage range, and application-specific peripheral assignments.

The ADC, DAC, op amp, and capacitive-touch functions demand careful reference and grounding discipline. Route analog inputs with short, quiet paths; use a continuous ground reference beneath sensitive circuitry where the package drawing permits; and isolate touch electrodes from high-voltage or high-current switching regions. Validate touch performance and analog accuracy on the actual enclosure and PCB because mechanical construction and parasitic coupling can dominate nominal peripheral performance.

Compliance-Informationen

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The LCSC product listing identifies the device as RoHS. No additional environmental or automotive qualification information is stated for this ordering code.

Daten verifiziert am: 2026-11-20 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

ATSAML10D14A-YF datasheet ATSAML10D14A-YF pinout ATSAML10D14A-YF 24-SSOP ATSAML10D14A-YF specifications Microchip ATSAML10D14A-YF ATSAML10D14A-YF price ATSAML10D14A-YF stock ATSAML10D14A-YF lead time ATSAML10D14A-YF equivalent ATSAML10D14A-YF replacement ATSAML10D14A-YF vs ATSAML10D14A-MFT ATSAML10D14A capacitive touch controller ATSAML10D14A Cortex-M23 microcontroller 24-SSOP ARM Cortex-M23 16KB Flash

Verwandte Bauteile & Begriffe

Microchip Technology ATSAML10D14A-YF ATSAML10D16A-YF ATSAML10D18A-YF ATSAML10D14A-MFT ARM Cortex-M23 SAM L10 32-bit microcontroller embedded processor mixed-signal semiconductor 16 KB Flash memory 4 KB SRAM 2 KB EEPROM 24-SSOP SSOP package family surface-mount package capacitive-touch controller ADC DAC operational amplifier SERCOM ISO7816 smart-card interface active mode sleep mode RoHS
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen