ATSAML10D14A-YF - 32MHz Cortex-M23 MCU | Microchip
MPN: ATSAML10D14A-YF ✓ Hoạt độngATSAML10D14A-YF Tóm tắt
A microcontroller is a programmable system-on-chip that integrates a processor core, memory, and peripherals into one device. The ARM Cortex-M23 core provides a compact 32-bit architecture with hardware integer arithmetic and efficient event handling. In the power hierarchy, the ATSAML10D14A-YF is a microcontroller within the broader category of embedded processors and mixed-signal semiconductors.
Key features include operation below 25 uA/MHz in active mode and below 100 nA in sleep mode, as stated by Microchip. The device also provides an enhanced peripheral touch controller, ADC, DAC, op amp, comparators, serial communications, and an ISO7816 smart-card interface. Its 16 KB Flash supports embedded firmware, while 4 KB of SRAM provides working memory for control loops, communication stacks, and user-interface logic.
The device uses the Microchip SAM L10 architecture and event system to coordinate asynchronous peripheral activity with low-power operation. Its 32 MHz processing rate gives designers enough performance for capacitive-touch interfaces, compact sensor nodes, low-cost security accessories, and industrial control modules without requiring a larger application processor. Multiple programmable peripheral functions also reduce the need for external analog and communication components.
Typical uses include capacitive-touch control panels, compact keypads, smart-card readers, security accessories, building controls, and small sensor nodes. The 24-SSOP package also supports assembly processes that can accommodate leaded rather than fine-pitch components, although board area remains greater than that of an equivalent VQFN package.
Designers should verify the exact peripheral pin mapping and power configuration in the manufacturer pin-description table before assigning PCB tracks. Place decoupling capacitors beside the supply pins, route sensitive analog inputs away from switching nodes, and use the sleep-mode characteristics as a starting point for battery-life calculations rather than a complete system power budget.
Bộ thay thế dễ dàng lắp đặt cho ATSAML10D14A-YF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATSAML10D14A-YF (cùng hình factor và footprint) — khác nhau ở Active Mode Current, Package, RoHS Status, Sleep Mode Current.
ATSAML10D16A-YF
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATSAML10D18A-YF
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ATSAML10D14A-YF Tỷ lệ tối đa & tính chất điện
| Manufacturer | Microchip Technology |
| Product Type | ARM Cortex-M23 Microcontroller |
| CPU Core | ARM Cortex-M23 |
| Architecture | SAM L10 |
| Bit Width | 32-bit |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 16 KB (16K x 8) |
| SRAM | 4 KB |
| EEPROM | 2 KB |
| Active Mode Current | Less than 25 uA/MHz |
| Sleep Mode Current | Less than 100 nA |
| Supply Voltage Range | 1.62 V to 3.63 V |
| Hộp | 24-SSOP, 208 mil |
| Peripheral Interface | SERCOM |
| Analog Peripherals | ADC, DAC, OPAMP |
| Touch Controller | Enhanced peripheral touch controller |
| Security Peripheral | ISO7816 smart-card interface |
| Trạng thái RoHS | RoHS |
Hướng dẫn cấu hình chân ATSAML10D14A-YF 24-ssop, 208 mil
Cấu hình chân cho ATSAML10D14A-YF (24-ssop, 208 mil gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho ATSAML10D14A-YF.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ATSAML10D14A-YF phù hợp cho 6 Áp dụngs: Capacitive-Touch Control Panels, Smart-Card Readers and Access Controls, Battery-Powered Sensor Nodes, Industrial Control Modules, Connected Building Controls, Compact Security and Keypad Accessories.
Capacitive-Touch Control Panels
The ATSAML10D14A-YF fits compact keypad and control-panel designs because its enhanced peripheral touch controller is paired with a 32 MHz ARM Cortex-M23 core and a 16 KB Flash footprint. The controller can evaluate touch events while the application code manages lighting, feedback, and communication. Its 4 KB SRAM provides room for event buffering and interface state, while the 2 KB EEPROM supports nonvolatile configuration such as calibration offsets or device settings. A key engineering consideration is that the touch peripheral alone does not determine sensitivity; electrode geometry, guard-ring construction, PCB cleanliness, and grounding often have a greater effect than software filtering.
Được đề xuất
Smart-Card Readers and Access Controls
The ATSAML10D14A-YF is appropriate for compact smart-card readers because Microchip highlights its ISO7816 interface alongside the low-power Cortex-M23 core. It can coordinate card communication, request authentication, drive indicator feedback, and expose a host interface without requiring a separate security controller. The 16 KB Flash is suitable for a focused embedded application, and operation below 25 uA/MHz in active mode supports energy-conscious access hardware. The final design still requires careful treatment of the ISO7816 clock and data lines, plus the protection components specified by Microchip for exposed card-contact circuitry.
Được đề xuất
Battery-Powered Sensor Nodes
The ATSAML10D14A-YF suits compact battery-operated sensor nodes because its sleep-mode current is specified below 100 nA and its active-mode consumption is below 25 uA/MHz. A design can wake on a timer or external interrupt, sample an analog channel, process the result, and return to sleep without continuously powering the CPU. The 1.62 V to 3.63 V operating range permits direct integration with low-energy rails, although the regulator's own quiescent current and sensor leakage must be included in the system budget. Firmware should disable unused peripherals and GPIO states aggressively to approach the manufacturer low-power figures in real hardware.
Được đề xuất
Industrial Control Modules
The ATSAML10D14A-YF can serve as the control processor in small industrial modules that require deterministic peripheral handling without the memory overhead of a larger MCU. SERCOM interfaces support flexible serial connectivity, while the ADC, DAC, op amp, and comparators provide local analog conditioning. Its 32 MHz Cortex-M23 core has ample capacity for event handling, state machines, and communication protocols within the available 16 KB Flash and 4 KB SRAM. Industrial equipment designers should still plan for transient protection, isolation requirements, and grounding discipline, because the MCU's internal analog block does not replace external protection at field-facing connectors.
Được đề xuất
Connected Building Controls
The ATSAML10D14A-YF is useful in connected thermostats, room controllers, and small building-automation nodes where a touch interface, analog sensing, and low-power operation must coexist. The enhanced touch controller can support local user interaction, while ADC and comparator resources handle simple sensing functions. SERCOM peripherals can bridge the controller to external transceivers or standardized building networks. Because the device offers only 16 KB of Flash and 4 KB of SRAM, designers should select a lightweight protocol stack and avoid moving protocol processing to a separate platform. The 24-SSOP package also makes the part suitable for higher-volume leaded-package assembly when fine-pitch leadless assembly is unnecessary.
Được đề xuất
Compact Security and Keypad Accessories
The ATSAML10D14A-YF suits small keypad locks, credential readers, and portable security accessories that combine local input handling with smart-card communication. Its enhanced peripheral touch controller can support capacitive keys, and the ISO7816 interface provides a path to smart-card transactions. The Cortex-M23 core can run the device protocol and local user logic while its low-power modes help manage standby consumption. Designers should treat security-sensitive code, key storage, and authentication policy as separate architecture requirements rather than relying on the presence of an ISO7816 interface alone, and should verify the intended package pin mapping against the manufacturer datasheet before layout release.
Được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATSAML10D14A-YF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATSAML10D16A-YF | ATSAML10D18A-YF |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 24-SSOP | 24-SSOP | 24-SSOP |
| Pin Compatibility | 24-SSOP reference footprint | Same family and package; verify pin table before substitution | Same family and package; verify pin table before substitution |
Bảo phân biệt quan trọng
- Combines capacitive-touch sensing with advanced analog functions (vsATSAML10D14A-MFT)
- Lower-power architecture for compact embedded products (vsATSAML10D14A-MFT)
- Package suited to leaded-package assembly (vsATSAML10D14A-MFT)
Ghi chú thiết kế
Use the less-than-25-uA/MHz active figure and less-than-100-nA sleep figure as component-level targets. Estimated active current at 32 MHz is below 800 uA before external loads are added, calculated from 32 MHz multiplied by 25 uA/MHz. Actual firmware should clock-gate unused blocks, disable unused GPIO pull resistors, and place the MCU into the deepest permitted sleep state during idle intervals. Include regulator quiescent current and sensor leakage in the complete battery budget.
Assign every net from the manufacturer pin-description table rather than relying on package position alone. Place the required bypass capacitors adjacent to the device's supply pins, provide a clean return path for analog and touch channels, and keep high-current or switching traces away from sensitive inputs. The 24-SSOP footprint has 0.208-inch lead spacing, so confirm board outline, drill placement, solderability, and assembly clearances against the current package drawing.
Do not substitute ATSAML10D14A-MFT for this part on an existing board: its VQFN land pattern is not compatible with the 24-SSOP footprint. Also avoid assuming that all family variants share the same exposed-pin functions, alternate-function routing, or maximum clock settings. Before releasing a substitution, compare the ordering code, package drawing, pin table, memory configuration, operating-voltage range, and application-specific peripheral assignments.
The ADC, DAC, op amp, and capacitive-touch functions demand careful reference and grounding discipline. Route analog inputs with short, quiet paths; use a continuous ground reference beneath sensitive circuitry where the package drawing permits; and isolate touch electrodes from high-voltage or high-current switching regions. Validate touch performance and analog accuracy on the actual enclosure and PCB because mechanical construction and parasitic coupling can dominate nominal peripheral performance.
Thông tin tuân thủ
The LCSC product listing identifies the device as RoHS. No additional environmental or automotive qualification information is stated for this ordering code.