Microchip Technology

ATTINY10-TSHR - 12MHz 8-Bit AVR MCU | Microchip Technology

Teilenummer: ATTINY10-TSHR ✓ Aktiv
1.8 V to 5.5 V Vdss SOT-23-6 Package 12 MHz Speed 1 KB Flash (512 x 16) Memory
MOQ: 1 |

ATTINY10-TSHR Übersicht

The Microchip Technology ATTINY10-TSHR is a low-power 8-bit AVR RISC microcontroller operating up to 12 MHz, with 1 KB of Flash program memory, 32 B of SRAM, four general-purpose I/O lines, and a SOT-23-6 package. The -TSHR ordering suffix identifies the factory-programmable, industrial-temperature configuration.

An 8-bit RISC microcontroller is a compact embedded-processing device that executes instructions from on-chip Flash memory and uses SRAM for working data. The AVR architecture belongs to the microcontroller hierarchy, where reduced instruction complexity enables deterministic control, low power consumption, and compact embedded-system designs. The ATTINY10-TSHR is particularly suited to applications requiring a small controller with limited memory and a minimal board footprint.

The device combines 1 KB of ISP Flash memory with 32 B of SRAM and four general-purpose I/O lines. Its 16 general-purpose working registers support efficient instruction execution, while a 16-bit timer/counter provides two PWM channels for timing, dimming, or basic waveform-generation tasks. Operation from 1.8 V to 5.5 V allows use across low-voltage and conventional supply systems, with the 12 MHz maximum operating speed specified at 4.5 V to 5.5 V.

The ATTINY10-TSHR also includes a four-channel, 8-bit ADC and QTouch capacitive-sensing support. These resources expand the device beyond simple digital I/O control, enabling compact sensing nodes, simple analog measurement systems, and capacitive user interfaces. Its AVR enhanced RISC architecture is designed to approach one MIPS of throughput per megahertz, although actual application performance depends on instruction mix and peripheral activity.

Typical uses include battery-powered sensor nodes, capacitive-control panels, compact consumer accessories, industrial controls, lighting modules, and compact power-management products. The SOT-23-6 package supports automated assembly and reduces PCB area, while the small memory footprint favors simple control tasks rather than protocol stacks, graphical interfaces, or data-intensive applications.

Designers should verify the complete pin assignment and programming interface against the manufacturer datasheet before layout. The 12 MHz operating limit applies at a 4.5 V to 5.5 V supply, and operation from 1.8 V to 5.5 V does not imply that every peripheral runs at the maximum clock rate across the entire voltage range.

This page combines device specifications, practical application guidance, programming references, and carefully qualified same-package alternatives to support component selection and compact embedded-system design.

Drop-in-Alternativen für ATTINY10-TSHR – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit ATTINY10-TSHR (gleiche Bauform und Footprint) – abweichend in Timer/Counter, Package, Program Memory Size, General-Purpose Working Registers, Maximum Clock Speed.

Microchip Technology
Timer/Counter: 8-bit timer/counter with two PWM channels on the ATtiny4 family device
Package: 6-pin SOT-23-6
Vergleichen mit ATTINY10-TSHR →
Microchip Technology
Timer/Counter: 16-bit timer/counter with 2 PWM channels
Package: 6-pin SOT-23
Program Memory Size: 512 bytes (256 x 16)
Vergleichen mit ATTINY10-TSHR →
Microchip Technology
Timer/Counter: 16-bit timer/counter
Program Memory Size: 1 KB (512 x 16 bits)
Maximum Clock Speed: 10 MHz
Vergleichen mit ATTINY10-TSHR →
Microchip Technology
Timer/Counter: 16-bit with two PWM channels
Program Memory Size: 1 KB (512 x 16)
Maximum Clock Speed: 12 MHz
Vergleichen mit ATTINY10-TSHR →

ATTINY10-TS8R

✅ Drop-In
📦 SOT-23-6
Same SOT-23-6 footprint and same 12 MHz, 1 KB Flash, and 32 B SRAM ratings; ordering suffix differs by 0 MHz and 0 KB, with factory-programming and temperature conditions requiring review

📋 Referenzalternative (nicht im Katalog)

ATTINY9-TSHR

✅ Drop-In
Microchip Technology
📦 SOT-23-6
8-bit AVR RISC-based microcontroller · 1 KB (512 x 16) · ISP Flash · 32 x 8 bytes · 4 · 16 · 12 MHz · 16-bit with two PWM channels

Preis auf Anfrage

Datenblatt ansehen →

ATTINY9-TS8R

✅ Drop-In
Microchip Technology
📦 SOT-23-6
8-bit AVR RISC microcontroller · 1 KB (512 x 16 bits) · 32 bytes · 4 · 16 · 10 MHz · 16-bit timer/counter · 2

Preis auf Anfrage

Datenblatt ansehen →

ATTINY10-TSHR Grenzwerte & elektrische Eigenschaften

Architecture 8-bit AVR enhanced RISC
Maximum CPU Frequency 12 MHz
Program Memory 1 KB Flash (512 x 16)
Program Memory Type ISP Flash
SRAM 32 B
General-Purpose I/O Lines 4
General-Purpose Working Registers 16
Timer/Counter 16-bit with 2 PWM channels
ADC Resolution 8-bit
ADC Channels 4 channels
Operating Voltage Range 1.8 V to 5.5 V
12 MHz Operating Supply 4.5 V to 5.5 V
Architecture Throughput Approximately 1 MIPS per MHz
Capacitive Sensing QTouch supported
Gehäuse SOT-23-6
Montageart Surface mount
Temperature Grade Industrial
RoHS-Status Compliant
Programmable Configuration Factory programmable

ATTINY10-TSHR sot-23-6 Pinbelegungsleitfaden

Pinbelegung für ATTINY10-TSHR (sot-23-6-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.

Pinbelegungsdiagramm für ATTINY10-TSHR im sot-23-6-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für ATTINY10-TSHR.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

ATTINY10-TSHR ist geeignet für 6 Anwendungs: Capacitive User Interface, Battery-Powered Sensor Node, LED Dimming Controller, Compact Industrial Control Module, Consumer Accessory Controller, Low-Voltage Measurement Module.

📱

Capacitive User Interface

The ATTINY10-TSHR is suitable for a compact capacitive user interface because QTouch support combines with an 8-bit AVR core operating up to 12 MHz. Its four general-purpose I/O lines can support sensing and response functions while the 1 KB Flash memory limits the interface firmware to focused tasks such as button scanning, debouncing, status lighting, and wake behavior. The SOT-23-6 package reduces board area in wearable controls, appliance panels, and personal accessories. Firmware should include calibration, environmental compensation, and debounce logic, while the PCB should keep sensitive sensor traces short and route them away from switching nodes and high-current paths.

🧩

Battery-Powered Sensor Node

The ATTINY10-TSHR fits a small battery-powered sensor node because it operates from 1.8 V to 5.5 V and combines a four-channel, 8-bit ADC with low-power CMOS processing. The controller can sample external analog sensors, apply thresholds or simple scaling, and control an indicator or duty-cycled communication function. Its 12 MHz maximum speed provides responsive task execution when higher clock rates are needed, although the full-speed supply range is 4.5 V to 5.5 V. Use sleep modes and scheduled wake-ups to control energy use, and account for sensor standby current, pull networks, regulator efficiency, and leakage across the complete battery operating profile.

💡

LED Dimming Controller

The ATTINY10-TSHR can control a compact LED or indicator system using its 16-bit timer/counter and two PWM channels. The timer provides a useful timing base for brightness updates, fade sequences, periodic flashing, or simple power-control functions, while the 12 MHz CPU handles button input and state management. Two PWM outputs are sufficient for a dual-color indicator, a two-channel dimmer, or one channel paired with a discrete driver. Component selection must account for LED current, switching frequency, flicker behavior, and thermal dissipation in the external driver rather than treating the microcontroller pin as a direct high-power LED output.

🏭

Compact Industrial Control Module

The ATTINY10-TSHR is appropriate for a compact industrial control module that monitors a few analog or digital inputs and performs a defined local action. Its industrial-temperature ordering designation, four I/O lines, four ADC channels, and 16-bit timer support simple machine-interface tasks such as threshold monitoring, actuator timing, fault flags, and periodic status sampling. The six-pin package allows placement close to the controlled circuit, which can reduce trace length and board area. The design should provide suitable input conditioning, surge protection, grounding, and actuator-driver isolation because the MCU does not replace industrial protection components or provide isolation.

🔧

Consumer Accessory Controller

The ATTINY10-TSHR works well as a dedicated controller in a small consumer accessory where the required behavior is narrow, such as button interpretation, status indication, motor timing, or simple sensor interaction. Its 1 KB Flash and 32 B SRAM encourage a tightly scoped firmware design, while the SOT-23-6 footprint supports high-density assembly. The device can manage a simple product state machine and use its timer for repeatable timing operations. For production designs, confirm that the required firmware, bootloader strategy, and programming fixture fit the memory and programming constraints, and ensure that an external driver handles loads beyond the microcontroller's I/O capability.

📟

Low-Voltage Measurement Module

The ATTINY10-TSHR can serve as the controller in a low-voltage measurement module built around its four-channel, 8-bit ADC. A 12 MHz AVR core can sample configured channels, calculate simple ratios or thresholds, and present a local result through LEDs, a simple display interface, or another compact output method. Operating from 1.8 V to 5.5 V supports battery and energy-harvesting designs, although maximum speed depends on the selected supply voltage. The analog front end should establish the measurable input range, source impedance, filtering, and grounding, while calibration should account for ADC reference accuracy, temperature, and the tolerances of external resistive networks.

What are the key specifications of ATTINY10-TSHR?
The ATTINY10-TSHR is an 8-bit AVR microcontroller with a maximum clock frequency of 12 MHz, 1 KB of ISP Flash memory, 32 B of SRAM, four I/O lines, and a SOT-23-6 package. According to the Microchip ATtiny10 product page, it also provides 16 working registers, a 16-bit timer/counter with two PWM channels, and a four-channel, 8-bit ADC. These characteristics position it for compact embedded controls rather than connectivity-heavy or data-intensive designs.
What is the operating voltage of ATTINY10-TSHR?
The ATTINY10-TSHR operates from 1.8 V to 5.5 V, while its maximum 12 MHz operating frequency applies over a 4.5 V to 5.5 V supply range. According to the manufacturer datasheet, the lower voltage range supports low-power and battery-operated systems, but designers must not assume that the full clock specification is available at 1.8 V. Peripheral operating limits and clock behavior should be checked for the selected supply voltage.
Where can I download the ATTINY10-TSHR datasheet PDF?
The ATTINY10-TSHR datasheet is available from the Microchip ATtiny10 product page and the linked manufacturer documentation. The datasheet contains the authoritative pin descriptions, memory map, electrical characteristics, clock requirements, programming connections, and package drawings. Use the manufacturer documentation when defining PCB tracks because the abbreviated SOT-23-6 outline alone does not identify each signal function or its electrical constraints.
Where can I find the ATTINY10-TSHR pinout?
The ATTINY10-TSHR pinout is documented in the manufacturer pin-description table and package drawing for the SOT-23-6 device. The part includes power, ground, programming, reset, and I/O-related connections, so a complete board schematic must use the exact pin numbers rather than relying on a generic six-pin layout. The programming-interface connections should also be checked against the supported programmer instructions.
How do I program an ATTINY10-TSHR?
The ATTINY10-TSHR can be programmed through its TPI programming interface using compatible tools such as the STK600 or AVRISPmkII. According to Microchip's ATtiny10 programming guidance, the debugger, target voltage, and TPI connections must be configured correctly. In-circuit programming also requires a design that exposes the required programming signals without placing the interface permanently in a state that prevents firmware updates.
What programmer is compatible with ATTINY10-TSHR?
Compatible programming solutions include the STK600 and AVRISPmkII configured for the ATTINY10 TPI interface. The manufacturer programming guide specifically identifies those tools for ATtiny10 devices. Tool compatibility alone does not guarantee correct operation: the programmer must also support the device family, use the correct TPI connection arrangement, provide an acceptable target voltage, and avoid programming settings that conflict with fuse configuration.
ATTINY10-TSHR vs ATTINY85 - which microcontroller is better?
The ATTINY10-TSHR is better for a compact control requiring only 1 KB Flash, 32 B SRAM, four I/O lines, and a six-pin package, whereas the ATTINY85 offers a larger resource set that makes it suitable for more demanding control functions. According to the manufacturer family information, the ATTINY10 is a 12 MHz AVR device with a four-channel ADC and QTouch support. The better choice depends on memory, I/O, timing, and package requirements rather than clock speed alone.
When should I choose ATTINY10-TSHR over a larger AVR microcontroller?
Choose the ATTINY10-TSHR when the final design requires only four general-purpose I/O lines, 1 KB of program memory, and 32 B of SRAM. It is particularly attractive in SOT-23-6 boards where footprint, low supply voltage, and simple control functions matter. Select a larger AVR controller when firmware growth, additional I/O, more timers, communication peripherals, or higher RAM requirements make the ATTINY10's resources inadequate.
Is ATTINY10-TSHR suitable for battery-powered projects?
The ATTINY10-TSHR is suitable for battery-powered projects because it is a low-power CMOS AVR device with a 1.8 V to 5.5 V operating range. The SOT-23-6 package also minimizes board area, and the four-channel, 8-bit ADC supports compact sensing designs. Battery life still depends on the selected operating mode, sensor load, pull-up networks, regulator efficiency, and how frequently the microcontroller wakes to process measurements.
Can ATTINY10-TSHR replace ATTINY10-TS8R?
The ATTINY10-TS8R is the closest qualified same-package alternative for the ATTINY10-TSHR because both use the SOT-23-6 format and retain the same 12 MHz, 1 KB Flash, and 32 B SRAM headline ratings. The ordering suffixes must still be checked for factory-programming and temperature requirements before substitution. Firmware, fuse configuration, pin function, and qualification requirements should be reviewed as part of any replacement approval.
What can replace ATTINY10-TSHR on the same PCB?
The ATTINY10-TS8R is a same-package replacement candidate for the ATTINY10-TSHR because it shares the SOT-23-6 footprint and the same headline 12 MHz, 1 KB Flash, and 32 B SRAM ratings. ATtiny9-TSHR and ATtiny9-TS8R are additional same-package comparison candidates, but peripheral differences may affect firmware and pin-function compatibility. No cross-brand drop-in replacement is established, so an engineering review is required before substitution.
Is there an ATTINY10-TSHR equivalent from another manufacturer?
No verified cross-brand, pin-compatible SOT-23-6 equivalent was identified for the ATTINY10-TSHR. The ATTINY10-TS8R and ATtiny9 variants are Microchip devices in the same package family, but MCU replacement requires matching pin functions, clock behavior, memory, timers, ADC behavior, programming interface, fuses, and software assumptions. Use the Request a Quote form on this page to discuss sourcing support for an approved substitution.
Can ATTINY10-TSHR be used for Arduino projects?
The ATTINY10-TSHR can be used in small Arduino-inspired or custom embedded projects, but software support is more limited than for widely supported ATmega boards. Its 1 KB Flash memory and four I/O lines constrain library size and application complexity. Microchip's ATtiny10 programming guidance identifies supported programming tools, and developers should confirm that their build system and libraries support the ATtiny10's peripheral and memory organization.
What projects suit the ATTINY10-TSHR?
The ATTINY10-TSHR suits compact projects such as capacitive-control panels, low-voltage sensor nodes, simple lighting controllers, and dedicated accessory controls. Its four-channel, 8-bit ADC supports basic analog measurements, while two PWM channels can drive dimming, indicators, or low-power actuators. Projects requiring extensive serial communication, large libraries, graphical interfaces, or extensive data storage should use a higher-capacity microcontroller instead.
Where can I buy ATTINY10-TSHR and check availability?
Use the Request a Quote form on this page to request current ATTINY10-TSHR availability, quantity, and lead-time confirmation for your required packaging configuration. The manufacturer product listing identifies the device as factory programmable, while its exact stock status can change by shipment date and order quantity. For production planning, specify the reel configuration, programming requirement, annual usage, and target delivery date with the request.
How much does ATTINY10-TSHR cost and what is its lead time?
Current commercial terms for the ATTINY10-TSHR should be requested through the Request a Quote form on this page. The form allows quantity, packaging, programming, and delivery requirements to be stated without relying on a potentially stale list price. Lead time can vary with order quantity and whether the shipment is standard stock or a factory-programmed configuration, so confirm the production schedule before committing the device to a build.

Technische Referenzdaten für ATTINY10-TSHR – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the ATTINY10-TSHR for a compact, low-voltage control requiring an 8-bit AVR core, 12 MHz operation, 1 KB Flash, four I/O lines, four ADC channels, and SOT-23-6 packaging. It is well suited to capacitive interfaces, simple measurement modules, LED dimming, and dedicated accessory controllers. Consider ATTINY10-TS8R first when the PCB and memory configuration match but the ordering, temperature, or factory-programming requirements differ. Evaluate ATTINY9-TSHR or ATTINY9-TS8R only after checking pin functions, timer behavior, ADC characteristics, fuses, and firmware dependencies. Move to a larger AVR or another MCU family when the application needs more RAM, more program storage, additional communication peripherals, or broader software support. Because no cross-brand, pin-compatible alternative is established, changing manufacturers generally requires a full hardware and firmware redesign rather than a drop-in substitution.

Vergleich mit Alternativen

Parameter Dieses Produkt ATTINY10-TS8R ATTINY9-TSHR ATTINY9-TS8R
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package SOT-23-6 SOT-23-6 SOT-23-6 SOT-23-6
CPU Architecture 8-bit AVR enhanced RISC 8-bit AVR 8-bit AVR 8-bit AVR
Maximum Clock Frequency 12 MHz 12 MHz 12 MHz 12 MHz
Flash Memory 1 KB 1 KB 1 KB 1 KB

Wichtigste Unterscheidungsmerkmale

  • Combines a compact six-pin package with four-channel ADC support (vs. ATTINY10-TS8R)
  • Maintains the same headline memory and clock ratings as the closest ordering variant (vs. ATTINY10-TS8R)
  • Uses a six-pin SOT-23-6 footprint with four application I/O lines (vs. ATTINY9-TSHR)

Designhinweise

Place the decoupling capacitor immediately across the ATTINY10-TSHR supply and ground pins, with the shortest possible connection between the capacitor and the device. The 1.8 V to 5.5 V operating range supports low-power designs, but the 12 MHz maximum frequency applies only over the 4.5 V to 5.5 V supply range. Route the TPI programming signals so the programming fixture can reach them reliably, and keep sensitive analog or capacitive-sensing traces away from fast-switching and high-current paths.

Treat the ATTINY10-TSHR as a low-duty-cycle control component rather than a general-purpose processor. Its 1 KB Flash and 32 B SRAM encourage compact firmware, while the four-channel, 8-bit ADC supports simple measurements without requiring a larger controller. For battery systems, calculate the average current from active processing, ADC sampling, peripheral operation, and sleep leakage instead of relying only on the active operating current. Confirm the regulator's quiescent current and dropout behavior over the complete 1.8 V to 5.5 V input range.

Do not assume that every ATtiny10-TSHR substitution is automatically firmware- and pin-compatible. Check the exact pin-description table, TPI interface, fuse configuration, ADC behavior, timer channels, startup timing, and factory-programming method for the proposed device. The SOT-23-6 package is shared by several compact AVR devices, but package equality alone does not guarantee equivalent peripheral behavior. Perform a hardware and firmware regression test before approving ATTINY10-TS8R, ATTINY9-TSHR, or ATTINY9-TS8R as a replacement.

For QTouch capacitive sensing, follow the manufacturer's recommended electrode layout and keep the sensor electrode geometry stable between prototypes. Avoid placing ground pours or high-current return paths directly beneath sensitive electrodes unless the application circuit supports that arrangement. Provide controlled reference capacitance and clean sensor traces, and validate touch performance in the final enclosure because panel materials, humidity, grounding, and nearby conductors can materially affect coupling and sensitivity.

Compliance-Informationen

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

RoHS compliance is identified for the ATTINY10-TSHR. REACH, lead-free status, halogen-free status, conflict-minerals status, and automotive qualification are not established.

Ähnliche Suchanfragen

attiny10 tshr attiny10 tshr datasheet attiny10 tshr programming attiny10 datasheet attiny10 pinout attiny10 programming attiny10 price attiny10 programmer attiny10 vs attiny85 attiny10 arduino attiny10 projects ATTINY10-TSHR equivalent ATTINY10-TSHR replacement ATTINY10-TSHR SOT-23-6 pinout

Verwandte Bauteile & Begriffe

Microchip Technology ATTINY10-TSHR ATTINY10-TS8R ATTINY9-TSHR ATTINY9-TS8R ATtiny10 AVR 8-bit RISC microcontroller embedded microcontroller semiconductor ISP Flash memory SRAM QTouch capacitive sensing SOT-23-6 surface-mount package 12 MHz clock 1.8 V to 5.5 V operation 16-bit timer/counter PWM 4-channel 8-bit ADC TPI programming interface industrial temperature grade factory-programmable microcontroller
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen