ATTINY10-TSHR - 12MHz 8-Bit AVR MCU | Microchip Technology
MPN: ATTINY10-TSHR ✓ 啟用中ATTINY10-TSHR 概覽
An 8-bit RISC microcontroller is a compact embedded-processing device that executes instructions from on-chip Flash memory and uses SRAM for working data. The AVR architecture belongs to the microcontroller hierarchy, where reduced instruction complexity enables deterministic control, low power consumption, and compact embedded-system designs. The ATTINY10-TSHR is particularly suited to applications requiring a small controller with limited memory and a minimal board footprint.
The device combines 1 KB of ISP Flash memory with 32 B of SRAM and four general-purpose I/O lines. Its 16 general-purpose working registers support efficient instruction execution, while a 16-bit timer/counter provides two PWM channels for timing, dimming, or basic waveform-generation tasks. Operation from 1.8 V to 5.5 V allows use across low-voltage and conventional supply systems, with the 12 MHz maximum operating speed specified at 4.5 V to 5.5 V.
The ATTINY10-TSHR also includes a four-channel, 8-bit ADC and QTouch capacitive-sensing support. These resources expand the device beyond simple digital I/O control, enabling compact sensing nodes, simple analog measurement systems, and capacitive user interfaces. Its AVR enhanced RISC architecture is designed to approach one MIPS of throughput per megahertz, although actual application performance depends on instruction mix and peripheral activity.
Typical uses include battery-powered sensor nodes, capacitive-control panels, compact consumer accessories, industrial controls, lighting modules, and compact power-management products. The SOT-23-6 package supports automated assembly and reduces PCB area, while the small memory footprint favors simple control tasks rather than protocol stacks, graphical interfaces, or data-intensive applications.
Designers should verify the complete pin assignment and programming interface against the manufacturer datasheet before layout. The 12 MHz operating limit applies at a 4.5 V to 5.5 V supply, and operation from 1.8 V to 5.5 V does not imply that every peripheral runs at the maximum clock rate across the entire voltage range.
This page combines device specifications, practical application guidance, programming references, and carefully qualified same-package alternatives to support component selection and compact embedded-system design.
直接替換替代品,適用於 ATTINY10-TSHR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ATTINY10-TSHR (相同外形與佔位) — 差異在於 Timer/Counter, Package, Program Memory Size, General-Purpose Working Registers, Maximum Clock Speed.
ATTINY10-TS8R
✅ 直接替換📋 參考替代品(不在目錄中)
ATTINY9-TSHR
✅ 直接替換聯絡詢價
查看資料表 →ATTINY9-TS8R
✅ 直接替換聯絡詢價
查看資料表 →ATTINY10-TSHR 最大額定值與電氣特性
| Architecture | 8-bit AVR enhanced RISC |
| Maximum CPU Frequency | 12 MHz |
| Program Memory | 1 KB Flash (512 x 16) |
| Program Memory Type | ISP Flash |
| SRAM | 32 B |
| General-Purpose I/O Lines | 4 |
| General-Purpose Working Registers | 16 |
| Timer/Counter | 16-bit with 2 PWM channels |
| ADC Resolution | 8-bit |
| ADC Channels | 4 channels |
| Operating Voltage Range | 1.8 V to 5.5 V |
| 12 MHz Operating Supply | 4.5 V to 5.5 V |
| Architecture Throughput | Approximately 1 MIPS per MHz |
| Capacitive Sensing | QTouch supported |
| 封裝 | SOT-23-6 |
| 安裝類型 | Surface mount |
| Temperature Grade | Industrial |
| RoHS 狀態 | Compliant |
| Programmable Configuration | Factory programmable |
ATTINY10-TSHR sot-23-6 腳位配置指南
ATTINY10-TSHR(sot-23-6 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: ATTINY10-TSHR.
請參閱 資料表 以查看完整腳位配置。
典型應用
ATTINY10-TSHR 適用於 6 應用s: Capacitive User Interface, Battery-Powered Sensor Node, LED Dimming Controller, Compact Industrial Control Module, Consumer Accessory Controller, Low-Voltage Measurement Module.
Capacitive User Interface
The ATTINY10-TSHR is suitable for a compact capacitive user interface because QTouch support combines with an 8-bit AVR core operating up to 12 MHz. Its four general-purpose I/O lines can support sensing and response functions while the 1 KB Flash memory limits the interface firmware to focused tasks such as button scanning, debouncing, status lighting, and wake behavior. The SOT-23-6 package reduces board area in wearable controls, appliance panels, and personal accessories. Firmware should include calibration, environmental compensation, and debounce logic, while the PCB should keep sensitive sensor traces short and route them away from switching nodes and high-current paths.
推薦
Battery-Powered Sensor Node
The ATTINY10-TSHR fits a small battery-powered sensor node because it operates from 1.8 V to 5.5 V and combines a four-channel, 8-bit ADC with low-power CMOS processing. The controller can sample external analog sensors, apply thresholds or simple scaling, and control an indicator or duty-cycled communication function. Its 12 MHz maximum speed provides responsive task execution when higher clock rates are needed, although the full-speed supply range is 4.5 V to 5.5 V. Use sleep modes and scheduled wake-ups to control energy use, and account for sensor standby current, pull networks, regulator efficiency, and leakage across the complete battery operating profile.
推薦
LED Dimming Controller
The ATTINY10-TSHR can control a compact LED or indicator system using its 16-bit timer/counter and two PWM channels. The timer provides a useful timing base for brightness updates, fade sequences, periodic flashing, or simple power-control functions, while the 12 MHz CPU handles button input and state management. Two PWM outputs are sufficient for a dual-color indicator, a two-channel dimmer, or one channel paired with a discrete driver. Component selection must account for LED current, switching frequency, flicker behavior, and thermal dissipation in the external driver rather than treating the microcontroller pin as a direct high-power LED output.
推薦
Compact Industrial Control Module
The ATTINY10-TSHR is appropriate for a compact industrial control module that monitors a few analog or digital inputs and performs a defined local action. Its industrial-temperature ordering designation, four I/O lines, four ADC channels, and 16-bit timer support simple machine-interface tasks such as threshold monitoring, actuator timing, fault flags, and periodic status sampling. The six-pin package allows placement close to the controlled circuit, which can reduce trace length and board area. The design should provide suitable input conditioning, surge protection, grounding, and actuator-driver isolation because the MCU does not replace industrial protection components or provide isolation.
推薦
Consumer Accessory Controller
The ATTINY10-TSHR works well as a dedicated controller in a small consumer accessory where the required behavior is narrow, such as button interpretation, status indication, motor timing, or simple sensor interaction. Its 1 KB Flash and 32 B SRAM encourage a tightly scoped firmware design, while the SOT-23-6 footprint supports high-density assembly. The device can manage a simple product state machine and use its timer for repeatable timing operations. For production designs, confirm that the required firmware, bootloader strategy, and programming fixture fit the memory and programming constraints, and ensure that an external driver handles loads beyond the microcontroller's I/O capability.
推薦
Low-Voltage Measurement Module
The ATTINY10-TSHR can serve as the controller in a low-voltage measurement module built around its four-channel, 8-bit ADC. A 12 MHz AVR core can sample configured channels, calculate simple ratios or thresholds, and present a local result through LEDs, a simple display interface, or another compact output method. Operating from 1.8 V to 5.5 V supports battery and energy-harvesting designs, although maximum speed depends on the selected supply voltage. The analog front end should establish the measurable input range, source impedance, filtering, and grounding, while calibration should account for ADC reference accuracy, temperature, and the tolerances of external resistive networks.
推薦
工程參考資料,適用於 ATTINY10-TSHR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ATTINY10-TS8R | ATTINY9-TSHR | ATTINY9-TS8R |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SOT-23-6 | SOT-23-6 | SOT-23-6 | SOT-23-6 |
| CPU Architecture | 8-bit AVR enhanced RISC | 8-bit AVR | 8-bit AVR | 8-bit AVR |
| Maximum Clock Frequency | 12 MHz | 12 MHz | 12 MHz | 12 MHz |
| Flash Memory | 1 KB | 1 KB | 1 KB | 1 KB |
主要差異化特點
- Combines a compact six-pin package with four-channel ADC support (對比ATTINY10-TS8R)
- Maintains the same headline memory and clock ratings as the closest ordering variant (對比ATTINY10-TS8R)
- Uses a six-pin SOT-23-6 footprint with four application I/O lines (對比ATTINY9-TSHR)
設計說明
Place the decoupling capacitor immediately across the ATTINY10-TSHR supply and ground pins, with the shortest possible connection between the capacitor and the device. The 1.8 V to 5.5 V operating range supports low-power designs, but the 12 MHz maximum frequency applies only over the 4.5 V to 5.5 V supply range. Route the TPI programming signals so the programming fixture can reach them reliably, and keep sensitive analog or capacitive-sensing traces away from fast-switching and high-current paths.
Treat the ATTINY10-TSHR as a low-duty-cycle control component rather than a general-purpose processor. Its 1 KB Flash and 32 B SRAM encourage compact firmware, while the four-channel, 8-bit ADC supports simple measurements without requiring a larger controller. For battery systems, calculate the average current from active processing, ADC sampling, peripheral operation, and sleep leakage instead of relying only on the active operating current. Confirm the regulator's quiescent current and dropout behavior over the complete 1.8 V to 5.5 V input range.
Do not assume that every ATtiny10-TSHR substitution is automatically firmware- and pin-compatible. Check the exact pin-description table, TPI interface, fuse configuration, ADC behavior, timer channels, startup timing, and factory-programming method for the proposed device. The SOT-23-6 package is shared by several compact AVR devices, but package equality alone does not guarantee equivalent peripheral behavior. Perform a hardware and firmware regression test before approving ATTINY10-TS8R, ATTINY9-TSHR, or ATTINY9-TS8R as a replacement.
For QTouch capacitive sensing, follow the manufacturer's recommended electrode layout and keep the sensor electrode geometry stable between prototypes. Avoid placing ground pours or high-current return paths directly beneath sensitive electrodes unless the application circuit supports that arrangement. Provide controlled reference capacitance and clean sensor traces, and validate touch performance in the final enclosure because panel materials, humidity, grounding, and nearby conductors can materially affect coupling and sensitivity.
合規資訊
RoHS compliance is identified for the ATTINY10-TSHR. REACH, lead-free status, halogen-free status, conflict-minerals status, and automotive qualification are not established.